For targets with i2c not built-in this fixes following error:
Package kmod-drm is missing dependencies for the following libraries:
i2c-core.ko
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If ehci platform driver is loaded before the chipidea controller driver,
both are competing for the same IO resources and the generic driver gets
used for the hardware. This results in USB device mode being
unavailable.
Split generic EHCI support code out of kmod-usb2, so that the chipidea
driver can be included without also pulling in the generic one. Also
rework the load order, so that the chipidea driver gets loaded first, in
case both are installed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The following will enable the TPM kernel module, as well as support for
the atmel i2c TPM driver. Tested and confirmed working on an Aerohive
AP-121
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
HTB and TBF are the basic traffic shapers used by sqm-scripts. Moving
these into kmod-sched-core enables sqm-scripts to downgrade its
dependency from kmod-sched to kmod-sched-core, potentially making it
useful on devices with smaller flash sizes.
This adds around 30k to the size of kmod-sched-core (20k for sch_htb.ko
and 10k for sch_tbf.ko).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Changes the platform to use the Chipidea driver instead of the
generic USB host driver which has support for both host and
device modes (selected on boot).
The changes in 930-chipidea-pullup.patch are already in mainline.
I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I
can test the changes with a newer kernel.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
Fixes build failure for kmod-can-c-can-platform which depends on
kmod-regmap for kernel 4.1 and 4.4.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
bnx2 driver support for the x86 architecture. Includes module and
firmware for Broadcom BCM5706/5708/5709/5716 ethernet adapters.
Signed-off-by: George Amanakis <g_amanakis@yahoo.com>
Allow to load .cis firmware updates from userspace. Some of PCMCIA cards
need to update Card Information Structure (CIS) to work properly.
Signen-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Currently, installing kmod-sdhci fails with "sdhci is already loaded" since
"sdhci.ko" is inserted explicitely first, the implicitely loaded again when
"sdhci-pltfm.ko" is inserted as the latter depends on the former.
Remove the explicit autoprobe of "sdhci.ko" to fix the postinstall script.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This will avoid loading it in the default configuration, which reduces
image size a bit, and (more importantly) improves performance by
avoiding some unnecessary netfilter hooks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this kernel module currently does not set submenu.
Fix this by adding it to the "Others" submenu
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This just adds the kmods for these kernel modules.
This is found on some Lantiq / Intel reference boards.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ESP algorithms in CBC mode require echainiv, so have kmod-ipsec
depend on kmod-crypto-echainiv.
See upstream commit 32b6170ca59ccf07d0e394561e54b2cd9726038c.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Package the driver for the DS1374 chip present on the T4240RDB.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix missing symbol]
FS#256
Fix audio not working due to unset SND_PCM_TIMER. CONFIG_SND_PCM_TIMER
is required for ALSA to work (at least for some audio devices),
otherwise applications using sound may fail. Can be reproduced by
installing "alsa-utils-tests" and running "speaker-test":
...
ALSA lib pcm_direct.c:1159:(snd1_pcm_direct_initialize_poll_fd) unable to open timer 'hw:CLASS=3,SCLASS=0,CARD=0,DEV=0,SUBDEV=0'
ALSA lib pcm_dmix.c:1106:(snd_pcm_dmix_open) unable to initialize poll_fd
Playback open error: -19,No such device
The kernel size does not increase, only the size of the kernel module
increases.
Signed-off-by: Dmitry Sutyagin <f3flight@gmail.com>
This is upstream alternative for LEDE's ledtrig-usbdev. It's main
advantages are:
1) Support for assigning more than 1 USB port to the LED
2) Setting proper state when activating with device already connected
3) FWIW it's an upstream driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes the following error when mounting a ext4 filesystem
----
[ 166.240000] EXT4-fs (sda1): Cannot load crc32c driver.
----
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
nf_tproxy_core was removed during 3.12 development with kernel commit
fd158d79d33d3c8b693e3e2d8c0e3068d529c2dc. The code was moved
to xt_TPROXY.c.
Fixes FS#212
Signed-off-by: Mathias Kresin <dev@kresin.me>
The kmod-sound-hda-core module attempts to package snd-hda-core.ko which
does not exist in Linux 3.18, therfore only use it for kernels >= 4.1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Prior to kernel 4.4, the hda-intel module depends on the hda-controller
utility submodule so bundle it for the older kernel versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
vfat filesystem fails to mount due to missing codepages with
factory-formatted flash drives. Depend on cp437 iso8559-1 and
utf8 nls modules as this covers most factory-formatted vfat
filesystems.
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
This patch set adds support for PCI Intel HD Audio
sound devices. This is useful for multimedia packages
in the packages feed that one may use to create audio
servers.
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
The nf_reject_* and nf_nat_masquerade_* modules are moved into the
corresponding kmod-nf- packages. Appropriate dependencies are added to the
kmod-nft- packages.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There is a separate package kmod-crypto-echainiv for echainiv.ko. Selecting
both packages led to a conflict, so remove the file from kmod-crypto-iv.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
br_netfilter.ko and the corresponding Kconfig symbol are already provided
by kmod-br-netfilter, which is a dependency of kmod-ebtables.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway)
need to be able to initialize the PCIe wifi device. Normally, this is done
during the early stages of booting linux, because the necessary init code
is read from the memory mapped SPI and passed to pci_enable_ath9k_fixup.
However,this isn't possible for devices which have the init code for the
Atheros chip stored on NAND in an UBI volume. Hence, this module can be
used to initialze the chip when the user-space is ready to extract the
init code.
Martin Blumenstingl made a few fixes and added support for lantiq:
kernel: owl-loader: add support for OWL emulation PCI devices
kernel: owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
kernel: owl-loader: use dev_* instead of pr_* logging functions
kernel: owl-loader: auto-generate the eeprom filename as fallback
kernel: owl-loader: add a debug message when swapping the eeprom data
kernel: owl-loader: add missing newlines in log messages
kernel: owl-loader: add support for the lantiq platform
These patches have been integrated. Thanks!
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
clean up usb gadget support:
- rename gadget modules so that they appear together and are easier to
identify as gadget modules
- make usb-lib-composite and usb-gadget hidden as there is no point in
selecting those without gadget drivers that require them as deps
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a patch to backport 5185c91385d73cdf79836eb8548e4726e43ae831
from Linux 4.8 adding USB2380 support to the NET2280 driver and
create an OpenWrt menu option to select it as a module.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Without any in-tree users enabled the Kernel's build process doesn't
actually build those modules. Enable some potential in-tree users
during Kernel build, so out-of-tree modules can depend on them.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9pfs is used by kvm to share files between host and guest,
add proper config option to enable it.
Signed-off-by: Matteo Croce <matteo.croce@canonical.com>
Targets that need switch drivers should select them in their kernel
config. This prevents some bloat from creeping into targets that don't
need switchdev/dsa
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch gets rid of the booke watchdog kmod package.
Instead the affected boards will enable it in their
kernel configs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The pps-ldisc kernel module supports Pulse-Per-Second connected with the CD (Carrier Detect) pin.
Signed-off-by: Stephen Walker <stephendwalker+github@gmail.com>
OpenWrt enables XATTR support pretty much universally, therefore
for filesystems that a loaded as modules also enable XATTR support
so that there are no unexpected missing capabilities.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
Instead of downloading the firmware for prism54 devices in the
wireless.mk do it in an extra package Makefile. To ship the complete
source code Intel ships our modified OpenWrt/LEDE + the content of the
dl directory. We do not want to have any files in the dl/ directory
which are not needed to build our images. The prism54 gets downloaded
every time independently of building kmod-net-prism54 or not. When it
is in a own package it only gets downloaded when the firmware package
is selected.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
93d5629a introduced a build failure on older platforms (<4.4)
because bmp085 is a boolean and not a tristate.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
add BMP085 and BMP180 pressure sensors
this driver supports the SPI and I2C and
older chips (BMP280 is supported by iio subsystem)
issue found when cleaning up omap/config
found while writing this patch that a
similar patch was submitted in June/July 2014 but not integrated
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Instead of downloading the firmware from some website take it from
linux-firmware package and do not download it separately any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kernel module for the OMAP Random Number Generator
found on OMAP16xx, OMAP2/3/4/5 and AM33xx/AM43xx
multimedia processors.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The igb kmods selects kmod-i2c-algo-bit which in turn is invisible until
kmod-i2c-core gets selected, causing kmod-igb to be hidden from menuconfig
as well.
Let kmod-igb select kmod-i2c-core as well in order to make it visible
in menuconfig right away.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Storage of such zones is provided by a nf_ct_ext struct, hence conntrack
memory foot print will not be increased if zones are not used.
Signed-off-by: Alin Năstac <alin.nastac@gmail.com>
Add packaging of it87 hardware monitor kernel module. It is
a common thermal and voltage monitor that is in many x86
(at least) devices, and is just another i2c hwmon module.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
Instead of converting the firmware files ourselves, use the files
generated during the normal kernel build process. This fixes packaging
kmod-e100 in the SDK environment.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
- depends on CFG80211 (upstream: 9da4aa48d04bbdbae3c959809e14da2bf0c53f61)
in os_dep/mon.c
This removes rtl8188eu completely from OpenWrt
since mac80211/compat-wireless/backports does not
provide staging wireless drivers
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 49049
IPVS (IP Virtual Server) implements transport-layer load balancing inside the Linux kernel
so called Layer-4 switching.
IPVS running on a host acts as a load balancer at the front of a cluster of real servers, it
can direct requests for TCP/UDP based services to the real servers, and makes services of
the real servers to appear as a virtual service on a single IP address.
Signed-off-by: Mauro Mozzarelli <mauro@ezplanet.net>
SVN-Revision: 48982
Fix buildbot error for mpc85xx.
ehci-fsl.ko should be packaged inside the usb2 package, because it
depends on the ehci kernel module. The fsl-mph-dr-of.ko module can stay
in an own package because the ehci driver depends on it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48932
