Commit Graph

21484 Commits

Author SHA1 Message Date
Piotr Dymacz
e68539aca4 ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.

Specification:

- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)

Other:

- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
  has additional logic circuit for M.2 SIM switching. The 'sim-select'
  will work only if both SIM slots are occupied. Otherwise, always slot
  with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
  loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
  has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
  miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
  slots but setting GPIO22 to high allows PERSTn control per slot, using
  GPIO23-25 (value is inverted)

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 01:37:54 +01:00
Piotr Dymacz
44d7a14a83 ramips: mt7621: refresh kernel config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 00:11:09 +01:00
Piotr Dymacz
fc0d0f5dfd ramips: provide label MAC for ALFA Network Tube-E4G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 00:10:52 +01:00
Piotr Dymacz
dfecf94c20 ramips: add support for ALFA Network R36M-E4G
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)

Other:

- there is a dedicated, 4-pin connector for optional RTC module (Holtek
  HT138x) with 'enable' input, not available at the time of preparing
  support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
  jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
  work only if both slots are occupied, otherwise U-Boot will always
  select slot with SIM card inside (user can override it later, in
  user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-13 21:45:31 +01:00
Piotr Dymacz
bc173ddd83 ramips: support dual image feature on ALFA Network boards
New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).

When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.

U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').

There are 3 additional env variables used to control 'dual image' mode:
- bootlimit   - maximum number of unsuccessful boot tries (default: '3')
- bootcount   - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
                it is set and 'bootcount' reaches 'bootlimit' value,
                U-Boot will start web-based recovery which then updates
                both partitions with provided image

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-13 21:45:31 +01:00
Sungbo Eo
261c746631 ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 16:21:59 +01:00
Sungbo Eo
fe6a04a8fe ramips: change status LED of Samsung CY-SWR1100
Use power LED for status indication and free WPS LED for other uses.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 16:05:19 +01:00
Sungbo Eo
aabdf6991c ramips: improve Samsung CY-SWR1100 support
This patch does the following:

- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address

Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-00040000: "devdata"
00040000-00050000: "devconf"

Power LED can be controlled by SoC GPIO. Add it in the dts leds node.

RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 16:03:42 +01:00
Sungbo Eo
7231c1edd9 ramips: fix MAC address setup for Samsung CY-SWR1100
Ethernet MAC address setup has been broken since c3e420f28c. Restore
original setting.

Fixes: c3e420f28c ("ramips: Add support for D-Link DCH-M225")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 15:57:53 +01:00
Adrian Schmutzler
a021268032 ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...

Fixes: FS#408

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 15:12:32 +01:00
Adrian Schmutzler
d421a8b944 ath79: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.

For future reference:

The MAC addresses of the FRITZ!WLAN Repeater 300E can be extracted
from the urlader key value store:

maca        *:6B
macb        *:6C
macwlan     *:6D
macdsl      *:6E

and be set by e.g.
addr=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 12:55:25 +01:00
Adrian Schmutzler
f4c3cfc620 ramips: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 12:51:38 +01:00
Koen Vandeputte
6589de9af7 kernel: bump 4.19 to 4.19.82
Refreshed all patches.

Remove upstreamed:
- 950-0295-sc16is7xx-Fix-for-Unexpected-interrupt-8.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-12 10:15:01 +01:00
Koen Vandeputte
ecfe552f99 kernel: bump 4.14 to 4.14.152
Refreshed all patches.

Altered patches:
- 301-arch-support-layerscape.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-12 10:15:01 +01:00
Koen Vandeputte
015fefa8e7 kernel: bump 4.9 to 4.9.199
Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-12 10:15:01 +01:00
Adrian Schmutzler
b5791118cc ath79: fix SUPPORTED_DEVICES for TP-Link TL-WR1043ND v3
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2

Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 19:03:20 +01:00
Manuel Kock
509894cffb lantiq: remove redundant WiFi LED on FRITZ!Box 7320
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.

Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-11 18:17:29 +01:00
Paul Spooren
e97113d5e1 x86,tegra,mvebu: image: use common reproducible IMG_PART_SIGNATURE
These targets are currently using more or less same SIGNATURE variable
which provides unique partition ID/signature, so it makes sense to
refactor it out into common IMG_PART_SIGNATURE variable which could be
reused by all targets.

This is another step in the direction of reproducible OpenWrt images.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[split into separate commit, renamed to IMG_PART_SIGNATURE]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-11 16:37:13 +01:00
Adrian Schmutzler
1c321237c2 ramips: split further base-files across subtargets
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:

- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 14:53:06 +01:00
Adrian Schmutzler
5dc535419f ath79: fix identifier for Nanostation M in ath9k caldata extraction
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit f1396ac753 ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 00:33:34 +01:00
David Bauer
b16d76bf40 ramips: correct Netgear WNDR3700v5 button flag
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.

Fixes commit 3459013257 ("ramips: correct R6220 button flag")

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-10 20:57:16 +01:00
David Bauer
3459013257 ramips: correct R6220 button flag
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.

The GPIO status reads the following for no buttons pressed:

root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7   (                    |wps                 ) in  hi
gpio-8   (                    |wifi                ) in  hi
gpio-14  (                    |reset               ) in  hi

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-09 19:15:40 +01:00
Álvaro Fernández Rojas
f586dd67ac brcm63xx: add linux 4.19 support
Boot tested on Comtrend AR-5387un:
https://gist.github.com/Noltari/57e5030455da8dc38e61f8c3a5922254

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jonas.gorski: make 4.19 an optional testing version; add gcc 8.3 fix]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2019-11-09 13:16:01 +01:00
Michael Heimpold
9673d5c7ab mxs: start a console on USB gadget serial ports
The I2SE Duckbill devices are pen-drive like and thus the usage
of the USB gadget subsystem is highly indicated.

Spawning a console if a serial gadget is configured saves
us from connecting a physical debug uart.

On Olimex OLinuXino Maxi/Mini boards, this does not hurt.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-11-09 12:56:34 +01:00
Michael Heimpold
9a5fd2fa85 mxs: switch to askconsole
Remove the dedicated tty name and use askconsole to spawn the console
on serial debug uart.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-11-09 12:56:32 +01:00
Michael Heimpold
002e312538 mxs: add support and switch to kernel 4.19
Also remove kernel 4.14 support and the meanwhile obsolete patch.

This was run-tested on I2SE Duckbill device and
Olimex OLinuXino Maxi board.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Tested-by: Zoltan HERPAI <wigyori@uid0.hu>
2019-11-09 12:56:28 +01:00
Adrian Schmutzler
f098c612b6 ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3
This moves shared code of the named devices into a common DTSI.

Remove setting status="okay" for &gpio0 as it's not disabled in
mt7620a.dtsi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:31 +01:00
Frederik Noe-Sdun
4a904b8b76 ramips: increase max SPI frequency to 50 MHz for EX3700/EX6130
Based on Macronix MX25L3205DM2I datasheet this is maximum
supported speed.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, improved commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:25 +01:00
Frederik Noe-Sdun
0cbd2c74d0 ramips: add support for Netgear EX6130
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the
device's web interface or via nmrpflash.

The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.

MAC adresses:
5.0 GHz  0x8004  *:9a
2.4 GHz  0x4     *:9b
lan      0x28    *:9b
wan      0x2e    *:9c

Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:16:14 +01:00
南浦月
0ff2385a92 ar71xx: fix tl-wdr3320-v2 upgrade
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.

Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 16:29:01 +01:00
Kristian Evensen
6ab84579c6 ipq40xx: u4019: use reset-gpios instead of phy-reset-gpio
Use reset-gpio instead of the custom phy-reset-gpio property to do phy
reset on the U4019. phy-reset-gpio was incorrectly introduced when we
added support for the U4019, and will be deprecated.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-11-07 22:51:37 +01:00
Daniel Danzberger
8db4496443 ipq40xx: wpj419: use reset-gpios property for phy reset
The old GPIO based phy reset (phy-reset-gpio) will be removed form
the ipq40xx mdio driver in the future.

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-07 22:51:37 +01:00
DENG Qingfang
6abce4d5e4 ipq40xx: mdio: remove support for phy-reset-gpio
Commit 6f6c00cfc9 ("ipq40xx: Add support for Unielec U4019") has
introduced support for `phy-reset-gpio` DT property, which isn't needed
as the MDIO already supports `reset-gpios`[1] which could be used instead.

1. https://elixir.bootlin.com/linux/v4.19.81/source/Documentation/devicetree/bindings/net/mdio.txt

Ref: PR#2511
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[commit title and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-07 22:51:37 +01:00
Adrian Schmutzler
a921945773 ramips: rename keys node formerly named button
For some devices, the keys node is named "button". Change name to
match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Adrian Schmutzler
4176100b06 ath79: replace generic button node names
In several DTS files, button nodes are just named buttonX or
xxx_button. This replaces the names with more specific names matching
the majority of key definitions.

While at it, fix name of keys node in one case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Martin Schiller
edbadec843 kernel: fix LED netdev trigger on interface rename
This fixes the netdev LED trigger for interfaces, which are renamed
during initialization (e.g. ppp interfaces).

Fixes: FS#2193
Fixes: FS#2239
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-11-07 00:10:18 +01:00
Paul Spooren
9fa061a7d3 ramips, mt7620: reproducible elecom-header uid/gid
The elecom-header renames the firmware image to v_0.0.0.bin, stores its
MD5 sum as v_0.0.0.md5 and tars both files again.

Both v_0.0.0 files are created as the build user making it harder to
reproduce.

This commit sets the owner/group of both files to root by adding extra
options to the final tar command.

Before:
0 buildbot   (101) buildbot   (102)  3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin
0 buildbot   (101) buildbot   (102)       33 2019-11-05 14:43:22.000000 v_0.0.0.md5

After:
0 root         (0) root         (0)  3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin
0 root         (0) root         (0)       33 2019-11-05 23:43:08.000000 v_0.0.0.md5

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-11-06 23:23:52 +01:00
Adrian Schmutzler
c8c4f7216e ath79: specify N and ND subversions of TL-WR941 with ALT0_MODEL
TP-Link's TL-WR941 is sold with detachable antennas
internationally (ND version), but with fixed antennas in China
(N version). While hardware and images are similar for both
variants of v2 and v4, they are different for v6.

Having both explicitly will make it easier for user to identify
the correct image, and most importantly will raise awareness
that N and ND are not necessarily always the same as for
TL-WR841 series.

With an image selection webpage, using ALT0_MODEL as in this
patch will provide the option to list versions for N and ND
separately.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 15:04:05 +01:00
Adrian Schmutzler
c7842ceaaa ramips: reorganize DTSI files for Netgear R devices
This reorganizes DTSI files for the Netgear R devices in mt7621
(and the WNDR3700 v5). It creates a common DTSI for all R (sercomm)
devices and distributes the remaining code in r6220.dtsi to R6220
and WNDR3700 v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:43:04 +01:00
Sungbo Eo
62b1559b56 ramips: improve support for WeVO 11AC NAS and W2914NS v2
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups

The factory partition scheme for MAC addresses (verified on both devices):
0x4   : WiFi 2.4GHz (label_mac-9)
0x28  : unused
0x2e  : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused

By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:31:32 +01:00
Adrian Schmutzler
15dc60e727 ath79: move eth0 to parent DTSI for ar9344 TP-Link CPE devices
The &eth0 node is the same for all TP-Link CPE devices in ar9344,
so move it to parent DTSI. While at it, do some minor DTS
harmonizations.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:51:20 +01:00
Andrew Cameron
bae0d47f2e ath79: add support for the TP-LINK CPE220 V3
This adds support for a popular low-cost 2.4GHz N based AP

Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
  common DTSI
- move &eth0 to parent DTSI
- fix several leading spaces, added/removed newlines

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:37:40 +01:00
Adrian Schmutzler
d2b9333ea9 ramips: remove default case for MAC address assignment
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.

This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).

Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.

In exchange, the current "do nothing" case can be removed, as it
will be the new default case.

The devices being put in the newly created explicit case were
determined as follows:

1. Create a list of all devices based on the DTS files.

2. Remove all devices already having an explicit entry setting
   their address.

3. Remove all devices that only have lan set up in the first part
   of 02_network:

mt7620:
   - alfa-network,tube-e4g
   - asus,rp-n53
   - buffalo,wmr-300
   - comfast,cf-wr800n
   - edimax,ew-7476rpc
   - edimax,ew-7478ac
   - elecom,wrh-300cr
   - hnet,c108
   - kimax,u25awf-h1
   - kimax,u35wf
   - kingston,mlw221
   - kingston,mlwg2
   - microduino,microwrt
   - netgear,ex2700
   - netgear,ex3700
   - netgear,wn3000rp-v3
   - planex,cs-qr10
   - planex,mzk-ex300np
   - planex,mzk-ex750np
   - ravpower,wd03
   - sercomm,na930
   - yukai,bocco
   - zbtlink,zbt-cpe102
   - zte,q7

mt7621:
   - gnubee,gb-pc1
   - gnubee,gb-pc2
   - linksys,re6500
   - mikrotik,rbm11g
   - netgear,ex6150
   - thunder,timecloud
   - tplink,re350-v1
   - tplink,re650-v1

mt76x8:
   - alfa-network,awusfree1
   - d-team,pbr-d1
   - glinet,vixmini
   - vocore,vocore2-lite
   - tama,w06
   - tplink,tl-mr3020-v3
   - tplink,tl-wa801nd-v5
   - tplink,tl-wr802n-v4
   - tplink,tl-wr902ac-v3
   - vocore,vocore2
   - widora,neo-16m
   - widora,neo-32m

rt288x:
   - buffalo,wli-tx4-ag300n
   - dlink,dap-1522-a1

rt305x:
   - allnet,all0256n-4m
   - allnet,all0256n-8m
   - allnet,all5002
   - allnet,all5003
   - alphanetworks,asl26555-16m
   - alphanetworks,asl26555-8m
   - asus,wl-330n
   - aximcom,mr-102n
   - dlink,dcs-930
   - easyacc,wizard-8800
   - hame,mpr-a2
   - hootoo,ht-tm02
   - huawei,d105
   - intenso,memory2move
   - planex,mzk-dp150n
   - rt305x dlink,dcs-930l-b1
   - sparklan,wcr-150gn
   - tenda,3g150b
   - tenda,3g300m
   - tenda,w150m
   - trendnet,tew-638apb-v2
   - unbranded,a5-v11
   - vocore,vocore-16m
   - vocore,vocore-8m
   - wansview,ncs601w
   - zorlik,zl5900v2

rt3883:
   - loewe,wmdr-143n
   - omnima,hpm

4. Put the remaining devices in the new case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:17:25 +01:00
Adrian Schmutzler
f4026ad24d ath79: DTS file style update and harmonization
This applies several style adjustments that have been requested in
recent reviews to older DTS files. Despite making the code base more
consistent, this will also help to reduce review time when DTSes
are copy/pasted.

Applied changes:
- Rename gpio-keys/gpio-leds to keys/leds
- Remove node labels that are not used
- Use label property for partitions
- Prefix led node labels with "led_"
- Remove redundant includes
- Harmonize new lines after status property
- Several smaller style fixes

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 00:27:55 +01:00
Sungbo Eo
763914ef1b ramips: improve netis WF-2881 support
This patch does the following:

1. remove u-boot-env partition
   Stock bootloader saves env variables at 0x80000 in flash,
   and there is nothing stored at 0x30000.
   By merging the partition "u-boot-env" with "u-boot",
   the partition table becomes the same as used in stock firmware:
   00000000-00080000: "Bootloader"
   00080000-00100000: "Config"
   00100000-00140000: "Factory"
   00140000-07f80000: "Kernel"

2. fix LAN/WAN MAC addresses and provide label MAC address
   Ethernet MAC addresses are stored in factory partition at:
   0xe000: LAN (label_mac)
   0xe006: WAN (label_mac+1)

3. fix LAN port order
   WF-2881 LAN ports are in reverse order of switch ports.

4. fix WiFi LEDs
   mt76 led nodes are added to make WiFi LEDs work.
   On top of this, mt76 node names are changed to more generic ones,
   and compatible strings are also added.

5. fix pinmux groups
   uart3 and uart2 pins are used as button and led, but jtag pins are not.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-06 00:27:55 +01:00
Petr Štetiar
04d6753d03 Revert "ipq806x: fix EA8500 switch control"
There is a problem with the EA8500, the switch will not work after soft
reboot, the only way to get it working again is to power cycle it
manually.

There are probably several issues in the play, it's quite hard to fix it
without having access to the actual device, so I don't see any other
option now, then revert the offending commit.

Ref: PR#2047
Fixes: FS#2168 ("Switch no longer work after restart on Linksys EA8500")
Reported-by: Adam <424778940z@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-06 00:21:15 +01:00
Adrian Schmutzler
443ba75c4e ath79: fix sorting and harmonize indent in tiny board.d files
This seems to have been overlooked when splitting base files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-05 13:14:29 +01:00
David Bauer
70d5989c9c ipq806x: use switch trigger for WAN LED on NETGEAR boards
With this commit, the WAN LED is triggered by the switch port state
instead of the eth0 netdev.
Otherwise, the LED is always illuminated, regardless of the WAN port
link state.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-04 18:50:53 +01:00
Sungbo Eo
6ea5f7d44c ramips: fix MTK_SOC for RT3662 devices
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.

Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-04 15:22:54 +01:00
Chuanhong Guo
09fe0c847d mediatek: add mt7629 subtarget with rfb image
base-files are added into subtarget directory like what's done
recently in ath79. For this subtarget, metadata checks are enforced
and a SUPPORTED_DEVICE is added to generate proper metadata.
Since we only have mt7629 support in 4.19, override KERNEL_PATCHVER
in target.mk for now.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-11-04 20:51:19 +08:00