Update iproute2 to latest stable 5.9; for the changes see https://lwn.net/Articles/834755/
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Hauke Mehrtens <hauke@huake-m.de>
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.
However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.
[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")
Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A lot of patches are outdated versions of upstreamed patches and
drivers.
So lets pull in the upstreamed patches and reorder remaining ones.
This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define wildcard patterns for filtering in target/linux/generic/config-filter
Preparation for supporting newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This replaces the previous (deprecated) method of collecting symvers data
in $(PKG_BUILD_DIR)/Module.symvers, which does not work on newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MikroTik recently changed again the way they store wlan calibration data
on devices. Prior to this change, ERD calibration data for all available
radios was stored within a single identifier node ("tag" in RouterBoot
parlance).
Recent devices have been seen with calibration (and BDF) data stored in
separate identifiers within LZOR packing for each radio: this patch
addresses this by:
1) ensuring that both variants are properly supported,
2) preserving backward compatibility with existing data consumers,
3) allowing for more than 2 calibration blobs to be exposed via sysfs.
Specifically, before this patch, the driver would provide a single sysfs
file named /sys/firmware/mikrotik/hard_config/wlan_data that contained
whatever calibration data found on the device's flash. After this patch,
when executed on a device that uses the old style storage, this behavior
is unchanged, but when executed on a device that uses new style storage
(for either traditional "ERD" packing or "LZOR" packing), the driver
replaces that single file with a folder containing one or more files
each containing the data encoded within individual identifiers.
As far as OpenWRT is concerned, this means that for devices which are
known to exist with both styles of data storage, a suitable hotplug stub
could look like this for e.g. the second radio:
wdata="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wdata" ] && caldata_sysfsload_from_file "$wdata" 0x8000 0x2f20 ) || \
( [ -d "$wdata" ] && caldata_sysfsload_from_file "$wdata/data_2" 0x0 0x2f20 )
This patch has been tested with LZOR old and new style packing on ipq4019,
and with old style on ath79.
Tested-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Шебанов Алексей <admin@ublaze.ru>
Tested-by: Alen Opačić <subixonfire@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Robert Marko <robimarko@gmail.com>
Backport upstream commits that sync the local kernel header
copies in this library, with up to date copies. These updated
headers ensure that libnetfilter-log users can use current
kernel functionality such as requesting that conntrack
information be appended to nflog events sent to userspace via
the NFULNL_CFG_F_CONNTRACK flag. This functionality has been
available since kernel version 4.4
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
Running the updated checkpatch version with spelling.txt show that
spelling mistakes happen to everyone.
> /target/linux$ fd .*.patch | xargs ../../scripts/checkpatch.pl | rg spell
WARNING: 'usefull' may be misspelled - perhaps 'useful'?
WARNING: 'afecting' may be misspelled - perhaps 'affecting'?
WARNING: 'usefull' may be misspelled - perhaps 'useful'?
WARNING: 'afecting' may be misspelled - perhaps 'affecting'?
WARNING: 'begining' may be misspelled - perhaps 'beginning'?
WARNING: 'superflous' may be misspelled - perhaps 'superfluous'?
WARNING: 'multipe' may be misspelled - perhaps 'multiple'?
WARNING: 'recieves' may be misspelled - perhaps 'receives'?
WARNING: 'retreive' may be misspelled - perhaps 'retrieve'?
WARNING: 'tranfer' may be misspelled - perhaps 'transfer'?
WARNING: 'additonal' may be misspelled - perhaps 'additional'?
WARNING: 'accomodate' may be misspelled - perhaps 'accommodate'?
[...]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Remove checks for device tree documentation as the OpenWrt tree comes
withouth the ./Documentation folder.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Checkpatch grown in functionallity and we should make use of that. If
OpenWrt patches should be upstream material they should also be checked
based on upstream checkpatch.pl instead of 2013.
Signed-off-by: Paul Spooren <mail@aparcar.org>
CONFIG_EFI_VARS has been disabled in
64bit x86 target in 2018 by the following commit
b0a51dab8c
the same reasons apply to Generic target, so
now it's disabled here too.
Leaving it enabled is also blocking compile as
a new symbol was added
EFI_CUSTOM_SSDT_OVERLAYS
that depends from CONFIG_EFI_VARS
and the build system stops and waits for
user input on what to do about it.
The Legacy and Geode targets never
had any EFI_xxx configs enabled so they
don't have this issue
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
This adds support for RTL839x SoCs in the ethernet and switch
drivers of the rtl838x architecture.
Reviewed-by: Andreas Oberritter <obi@saftware.de>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This change adds the configuration option to build and include
the nft_queue kernel module, which allows traffic to be queued up
to userspace from an nftables rule
Tested-by: Sébastien Delafond sdelafond@gmail.com
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
this patch fixes/improves follows:
- PATTERN_LEN is defined as a macro but unused
- redundant logic in count-up for "ptn"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The source date epoch is the only reproducible date close to the actual
build date. It can be used for tooling like the firmware wizard to show
the image age.
Signed-off-by: Paul Spooren <mail@aparcar.org>
On some systems I see the issue that crond dies after a few days.
Simply letting procd respawn the process is a simple safety-net.
Signed-off-by: Bruno Randolf <br1@einfach.org>
5c36293f06 resolv: Serialize processing in resolv/tst-resolv-txnid-collision
2dfa659a66 resolv: Handle transaction ID collisions in parallel queries (bug 26600)
05c025abca support: Provide a way to clear the RA bit in DNS server responses
f688bcd83d support: Provide a way to reorder responses within the DNS test server
eba0ce6058 Remove __warndecl
5337b2af4b Remove __warn_memset_zero_len [BZ #25399]
c6e794640c aarch64: Add unwind information to _start (bug 26853)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add support for the following devices:
- Xiaomi Mi Wi-Fi Router 3G v2
- Xiaomi Mi Router 4A Gigabit Edition
Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
[add explicit case for 4A, bump PKG_RELEASE,
improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.
Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
E600G v2 based on Qualcomm/Atheros QCA9531
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 5 x LED , 1 x Button(SW2-Reset Buttun), 1 x power input
- UART(J100) header on PCB(115200 8N1)
E600GAC v2 based on Qualcomm/Atheros QCA9531 + QCA9887
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 1T1R 5 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 6 x LED (one three-color led), 2 x Button(SW2-Reset Buttun),1 x power input
- UART (J100)header on PCB(115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original OpenWrt image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ath79-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to OpenWrt:
run lfw
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original OpenWrt image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ath79-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[rearrange in generic.mk, fix one case in 04_led_migration, update
commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The file lacks executable permissions, which makes it not being applied
during the first boot.
While at it, drop unneeded include.
Signed-off-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
[do not touch board name handling, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* noise: take lock when removing handshake entry from table
This is a defense in depth patch backported from upstream to account for any
future issues with list node lifecycles.
* netns: check that route_me_harder packets use the right sk
A test for an issue that goes back to before Linux's git history began. I've
fixed this upstream, but it doesn't look possible to put it into the compat
layer, as it's a core networking problem. But we still test for it in the
netns test and warn on broken kernels.
* qemu: drop build support for rhel 8.2
We now test 8.3+.
* compat: SYM_FUNC_{START,END} were backported to 5.4
* qemu: bump default testing version
The real motivation for this version bump: 5.4.76 made a change that broke our
compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Remove deferred sampling code which does not work well with rate tables +
probing.
Fix tx status handling if the first invalid rate idx is not set to -1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3023b0cc7352 bridge: add support for defining port member vlans via hotplug ops
a3016c451248 vlan: add pass-through hotplug ops that pass the VLAN info to the bridge
d59f3ddcbaf0 vlandev: add pass-through hotplug ops that pass the VLAN info to the bridge
dd5e61153636 bridge: show vlans in device status
a56e14afa612 bridge: preserve hotplug ports on vlan update if config is unchanged
d1e8884f8911 bridge: fix use-after-free bug on bridge member free
3a2b21001c3c system-dummy: set present state only for simple devices
ed11f0c0ffe4 bridge: only overwrite implicit vlan assignment if vlans are configured
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow configuring ipsets with dedicated config sections:
config ipset
list name 'ss_rules_dst_forward'
list name 'ss_rules6_dst_forward'
list domain 't.me'
list domain 'telegram.org'
instead of current, rather inconvenient syntax:
config dnsmasq
...
list ipset '/t.me/telegram.org/ss_rules_dst_forward,ss_rules6_dst_forward'
Current syntax will still continue to work though.
With this change, a LuCI GUI for DNS ipsets should be easy to implement.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The comment content can be useful for readers of both the log and code
Previously when dd command "records in/out" messages are not filtered
like now with get_image_dd, it's not clear that these messages are for
extracting boot sectors. E.g.
Before
== upgrade: Reading partition table from bootdisk...
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
After
== upgrade: Reading partition table from bootdisk...
== upgrade: Extract boot sector from the image
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The intent is to make it sound more like info level message, not some
error like "404 not found". x86 target at the moment makes image with
only signature but no metadata (ref commit f8141216 "x86: append
metadata to combined images").
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reviewed-By: Philip Prindeville <philipp@redfish-solutions.com>
This will have at least the following effects
- Log lines will have common prefix
- They will be output to stderr instead of stdout
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This is mainly to handle stderr message "Broken pipe", "F+P records
in/out" by common pattern "xcat | dd .."
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reviewed-By: Philip Prindeville <philipp@redfish-solutions.com>
