On lantiq a lot of stuff expects to be loaded to and executed at
0x80002000, including our own second stage bootloader.
For all build u-boots, the initial stack pointer is at 0x80008000. After
loading data to 0x80002000, every further stack operation corrupts the
loaded code.
Set the initial stack pointer to 0x80002000, to not overwrite code
loaded in memory. A stack of 0x2000 bytes has been proven as enough in
all done tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube we only have 0x6800 bytes of usable SRAM. Everything behind
can't be written to and a SPL u-boot locks up during boot.
Since it's a hard to debug issue and took me more than two years to fix
it, I consider it worth to include fix albeit SPL u-boots are not build
in OpenWrt.
I faced the issue while trying to shrink the u-boot to 64K since some
boards only have an u-boot partition of that size from the days
ifx-uboot was used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc10 the variables are placed more tightly to each other, which
uncovers a long existing bug in the lantiq DMA code. It can be observed
when using tftpboot with the filename parameter, which gets reset during
the tftpboot execution.
NetRxPackets[] points to cache line size aligned addresses. In
ltq_eth_rx_packet_align() the address NetRxPackets[] points to is
increased by LTQ_ETH_IP_ALIGN and the resulting not cache aligned
address is used further on. While doing so, the length/size is never
updated.
The "not cache aligned address" + len/size for a cache aligned address
is passed to invalidate_dcache_range(). Hence, invalidate_dcache_range()
invalidates the next 32 bit as well, which flashes the BootFile variable
as well.
variable BootFile is at address: 0x83ffe12c
NetRxPackets[] points to 0x83ffdb20 (len is 0x600)
data points to: 0x83ffdb22 (len is 0x600)
ltq_dma_dcache_inv: 0x83ffdb22 (for len 0x600)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffe120 (size: 32)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffdb40 (Bootfile: a.bin)
...
invalidate_dcache_range: 0x83ffe100 to 0x83ffe120 (Bootfile: a.bin)
invalidate_dcache_range: 0x83ffe120 to 0x83ffe140 (Bootfile: )
In ltq_dma_tx_map() and ltq_dma_rx_map() the start address passed to
ltq_dma_dcache_wb_inv() is incorrect. By considering the offset, the
start address passed to flush_dcache_range() is always aligned to 32, 64
or 128 bytes dependent on configured DMA burst size.
Fixes: FS#4113
Signed-off-by: Mathias Kresin <dev@kresin.me>
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
lwl s0,0(a1) - s0 == 0x6d000080
lwl s0,1(a1) - hangs
lwl s0,2(a1) - s0 == 0x0080xxxx
lwl s0,3(a1) - s0 == 0x80xxxxxx
It isn't clear whether it is a limitation of the flash chip, the EBU or
something else.
Force 8bit reads to prevent gcc optimizing the read with lwr/lwl
instructions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Host libraries are only build static, so let's pass --static to
pkg-config globally and remove the then unnecessary patches doing
exactly that individually.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.
For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
U-Boot 2021.10 has been released.
Rebase mediatek patches on top of new release and remove some patches
which have been merged upstream.
Tested on Bananapi BPi-R2 (mt7623), Bananapi BPi-R64 (mt7622) and
Linksys E8450 (mt7622).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Nobody ever updates PKG_RELEASE when changing devices or setup in
the various uboot-* packages. Use $(AUTORELEASE) so we still have
proper versioning there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix BPi-R2 GPIO LEDs to indicate boot into production or recovery
firmware in DTS and define them in default environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes compilation with GCC11.
Kept PKG_VERSION as there's some bug that chops off the 12 at the end.
Refreshed other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This adds the hash also for the aarch64 toolchain in addition to the
x86_64 toolchain. This gets the build on a Linux aarch64 host one step
further.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
bump version and remove patches that have been applied
176d701 wtmi: Wait 1s after putting PHYs INTn pin low
2eeccfe wtmi: Change comment describing reset workaround
e8c94a5 wtmi: Count RAM size from both CS0 and CS1
995979e wtmi: Rename macro
e29eb29 wtmi: soc: Fix start_ap_workaround() for TF-A with debug
81245ed wtmi: Use constant name PLAT_MARVELL_MAILBOX_BASE
18ccb83 wtmi: Do a proper UART reset with clock change as described in spec
15ff106 avs: Validate VDD value from OTP
3f33626 fix: clock: a3700: change pwm clock for 600/600 and 1200/750 preset
fb5e436 wtmi: uart: fix UART baudrate divisor calculation
Signed-off-by: sean lee <ilf@live.com>
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HPv2
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: W631GG8MB-12 128 MiB DDR3 SDRAM
(stock firmware is configured to use only 64 MiB)
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
24 ethernet port PoE status LEDs
2 SFP status/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESTORE" button on front panel
1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J41) with populated standard pin connector on
the left edge of the PCB, angled towards the side.
The casing has a rectangular cutout on the side that provides
external access to these pins.
Pinout (front to back):
+ GND
+ TX
+ RX
+ VCC
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
OEM upgrade method:
(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in
Linux by add "console=tty1" boot argument.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes a build problem seen after binutils 2.36 is used by default.
Fixes: 3f41153b1c ("toolchain/binutils: switch to version 2.36.1 by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CZ.NIC as part of Turris project released free and open source WTMI
application firmware wtmi_app.bin for all Armada 3720 devices.
This firmware includes additional features like access to Hardware
Random Number Generator of Armada 3720 SoC which original Marvell's
fuse.bin image does not have.
Add a patch which allows to pass the commit id, so the firmware is able
to identify itself, see a04bffeb.
Add a patch to disable linking with gold, since the ARM toolchain
doesn't ship gold.
Cherry-pick the 3 post-release fixes.
Signed-off-by: Andre Heider <a.heider@gmail.com>
02e23db fix compilation errors popped up by GCC-10
7c35173 Merge pull request #29 from pali/sync-a38x-uboot
bb734f5 mv_ddr: a38x: Use SOC_REGS_PHY_BASE for INTER_REGS_BASE
ee1ea84 mv_ddr: a38x: Fix ddr3 compilation
70f3e2e mv_ddr: Fix comment typo
dd960b4 mv_ddr: ddr3: Allow boards to specify CK_DELAY parameter
a87f4f7 mv_ddr: ddr3: only use active chip-selects when tuning ODT
3defcec mv_ddr: a38x: Add support for setting timing in hws_topology_map
Signed-off-by: Andre Heider <a.heider@gmail.com>
2efdb10 wtmi: Fix calculation of UART divider
4247e39 fix: twin die ddr porting guide
8ad7992 sys_init: Add missing newlines in debug mode
4ddea19 avs: Validate VDD value from OTP
c444aeb avs: Fix description for avs value 0x2e
1915b78 tim: Optimize code generated by gettimver.sh and print newline
21f566d tim: Print mv_ddr version and configuration on UART
840b70b tim: Use variable $DDRFILE where possible
c10e6ae tim: Fix waiting for UART TX ready
7bf95cf wtmi: Wait 3ms for the TX on UART to be empty prior resetting TX FIFO
63e8433 wtmi: Add "dirty" suffix to git commit and rebuild sys_init.bin binary when VERSION changes
e949b58 wtmi: During setup clock phase print CPU and DDR speed
10376b5 wtmi: Flush output on UART after the '\n' character
509c647 Makefile: Check that specified DDR_TOPOLOGY option is valid
Signed-off-by: Andre Heider <a.heider@gmail.com>
Revert to using the checked in `tbb_linux` image tool binary since building
it drags in the rather big Crypto++ project.
Cherry-pick the post-release UART fixes.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before
booting, separating U-Boot's environment into separate MTD partition
"u-boot-env" [1].
Check if "u-boot-env" MTD partition exists and set the uci defaults
accordingly.
[1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html
Signed-off-by: Marek Behún <marek.behun@nic.cz>
As the board name was changed to be identical to the device tree
compatible string (just like for other boards), also reflect that
change for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add fw_env configuration for the BPi-R2 which is a mediatek/mt7623
devboard which can be booted from SD Card or eMMC.
Auto detect the boot device and add environment accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All mediatek boards having fw_env accessible through uboot-envtools
belong to be mt7622 subtarget. Move the file, as subtarget-specific
files are supported for a while now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use built-in default environment instead of file in bootfs
* get rid of bootfs alltogether and use uImage.FIT
* auto-detect boot device like original script did
* add support for factory button
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ! Behavior change !
Old behavior: If the Reset button is held down during power-on
do factory reset and try booting recovery from TFTP forever.
If valid recovery is received via TFTP, write it to flash and boot.
New behavior: If the Reset button is held down during power-on
do factory reset, then try TFTP *once*, then try booting on-flash
recovery, then keep trying via TFTP forever until a valid image is
received.
Only if there is no bootable recovery stored on flash, store the
downloaded recovery. Then boot it.
* Set loadaddr to 0x48000000 in order to allow booting images larger
than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
0x48000000 gives us 384MB on devices with 512MB RAM, which should be
more than enough as a maximum size for uImage.FIT to be loaded.
* Widely unify device-specific default environment in preparation to
auto-generate it from parameters.
* backport upstream commit fixing MBR/DOS partitioning
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
In order for the grub2 boot-related code to compile normally, we have
made many adjustments to the compilation parameters. These adjustments
are not necessary for tools-related code. We apply these parameter
adjustments only to the boot-related code.
Signed-off-by: 李国 <uxgood.org@gmail.com>
