Commit Graph

159 Commits

Author SHA1 Message Date
Robert Marko
1b6f7ec679 qualcommax: ipq807x: add Netgear DEVICE_VARS
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.

Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-12-08 09:58:38 +01:00
Vladyslav Andreichykov
9c55866fad qualcommax: ipq60xx: add Linksys MR7350 support
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5052 2x2@80MHz or  802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
	* RGB system led
	* USB blue led

* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack

Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part

- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition

- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel

- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel

Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-12-07 16:00:58 +01:00
Robert Marko
2e4a0ebdde qualcommax: enable userspace regulator for ipq60xx as well
Userspace regulator consumer is rather usefull so enable it for ipq60xx
as well and remove from ipq807x only kernel config.

Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-12-07 16:00:58 +01:00
Robert Marko
3fbc740008 qualcommax: refresh config
Refresh the kernel config via kernel_menuconfig.

Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-12-07 16:00:58 +01:00
Chukun Pan
025dbeb70c qualcommax: ipq60xx: add Qihoo 360V6 support
Specifications:
  SoC:     Qualcomm IPQ6000 1.5GHz
  RAM:     NTCC256M16ER-EK 512MiB
  Flash:   W29N01HZSINA 128MiB
  ETH:     QCA8075 (3x LAN, 1x WAN)
  WLAN1:   2.4GHz 802.11b/g/n/ax 2x2
  WLAN2:   5GHz 802.11a/n/ac/ax 2x2
  Power:   DC 12V 1.5A
  Button:  Reset, Wps
  USB:     1x 2.0

Flash instructions:
  1. Download the initramfs image, rename it to
     initramfs.itb, host it with the tftp server.
  2. Interrupt U-Boot and run these commands:
     tftpboot initramfs.itb
     bootm
  3. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-12-06 10:59:38 +01:00
Chukun Pan
7e18e27e2f qualcommax: image: cleanup whitespace
Replace whitespaces with tab.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-12-06 10:59:38 +01:00
Robert Marko
1f53b7fb75 qualcommax: ipq60xx: remove source-only flag
Its been a while since we added ipq60xx as source-only, it is now
quite usable so lets remove the source-only flag to start building
official images.

I also plan to merge additional popular boards rather soon.

Link: https://github.com/openwrt/openwrt/pull/17065
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-25 10:26:33 +01:00
Rosen Penev
cd92cbddf8 kernel: filter out compiler opts from config
These get dynamically set based on compiler version. Not relevant for
targets.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-17 14:55:16 +01:00
Rosen Penev
da8abd4a1e kernel: remove GCC11_NO_ARRAY_BOUNDS
This symbol is no longer present.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-17 14:55:16 +01:00
Rodrigo Balerdi
491121288e ipq807x: delete unused legacy eMMC sysupgrade code
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-17 12:24:43 +01:00
Rodrigo Balerdi
17f84bba44 ipq807x: order devices alphabetically
Alphabetically sort devices in platform.sh

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-17 12:24:43 +01:00
Rodrigo Balerdi
fe481c9c47 ipq807x: prpl haze & qnap 301w: use the standard eMMC sysupgrade code
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.

Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-17 12:24:43 +01:00
Rodrigo Balerdi
5583d23189 ipq807x: nbg7815: use the standard eMMC sysupgrade code
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-17 12:24:43 +01:00
Robert Marko
8729d2a64d qualcommax: ipq60xx: add NSS reserved memory
It seems that despite NSS not being supported in OpenWrt the memory it
usually uses needs to be reserved anyway for stability reasons.

Link: https://github.com/openwrt/openwrt/pull/16928
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-12 17:42:37 +01:00
John Audia
85844cfc5c kernel: bump 6.6 to 6.6.60
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.60

Removed upstreamed:
	generic/backport-6.6/409-mtd-spi-nor-winbond-fix-w25q128-regression.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.60&id=27a58a19bd20a7afe369da2ce6d4ebea70768acd

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16892
Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-11-10 10:35:05 +01:00
Rosen Penev
cc98cfafd7
treewide: remove THIS_MODULE assignment
Matches upstream coccinelle check: api/platform_no_drv_owner.cocci.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16846
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-11-10 02:16:31 +01:00
Rodrigo Balerdi
3b221ba5af ipq807x: sax1v1k: fix sysupgrade not touching rootfs_data
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.

Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-09-24 00:07:55 +02:00
George Witt
9b33645566 ipq807x: add support for TP-Link EAP660 HD v1
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)

Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
   and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
   openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
   to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
   serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
   # tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
   # bootm
   You may need to type Ctrl+C and Enter before running these commands
   to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
   to be installed (check IP address):
   $ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
   # cd /tmp
   # sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.

Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-09-08 12:01:19 +02:00
John Audia
626fa75526 kernel: bump 6.6 to 6.6.45 and update config-6.6
Build on at leasst x86/64 failed without adding the new ksym:
CONFIG_PCP_BATCH_SCALE_MAX=5

According to www.kernelconfig.io[1], this option seems to apply
to all arches so I placed it in target/linux/generic/config-6.6

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.45

Removed upstreamed:
	generic/backport-6.6/719-v6.11-net-phy-realtek-add-support-for-RTL8366S-Gigabit-PHY.patch[2]

All other patches automatically rebased.

1. https://www.kernelconfig.io/config_pcp_batch_scale_max?q=&kernelversion=6.10.3&arch=x86
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.45&id=b45cbfa204b2a0985eb85dcb33d51714ee089bb9

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16144
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-13 00:34:16 +02:00
Kristian Skramstad
d62648d58c qualcommax: ipq60xx: add support for Cambium Networks XE3-4
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.

Hardware:
    Model:    Cambium Networks XE3-4
    CPU:      IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
    Memory:   1 GiB
    Flash:    512 MiB Macronix MX30UF2G18AC + W25Q128FW
    Ethernet: 1x 1 GbE   (QCA8072)
              1x 2.5 GbE (QCA8081)
    Buttons:  1x Reset
    Serial:   TX, RX, GND
    Baudrate: 115200
    Radios:   Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
              Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
              Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
              BLE 4.1
    Power:    32.0W 802.3bt5 PoE++
              25.5W 802.3at with USB, BT disabled
    Size:     215mm x 215mm
    Ports:    1x USB 2.0
    Antenna:  6 GHz: 6.29 dBi, Omni    30 dBm
              5 GHz: 6.12 dBi, Omni    31 dBm
              2.4 GHz: 4.85 dBi, Omni  29 dBm
    LEDs:     Multi-color status LEDs
    Mounting: Wall, ceiling or T-bar

Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
   one of the APs GND pins.
3. Transfer the initramfs image with TFTP
   (Default server IP is 192.168.0.120)
   # tftpboot factory.ubi
4. Flash the rootfs partition
   # flash rootfs
5. Reboot the AP
   # reset

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-08-08 22:57:22 +02:00
John Audia
96392789ae kernel: bump 6.6 to 6.6.43
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.43

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16010
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-28 19:46:16 +02:00
Robert Marko
3d7cb14211 qualcommax: ipq807x: add Asus RT-AX89X BX revision
This commit adds support for Asus RT-AX89X BX revision.

WARNING: Only the BX revision boards (So B1, B2 etc) are supported because
AX revision boards use IPQ8074 v1 SoC which is unsupported.

Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53 @ 2.2GHz
* RAM: 1024MB
* Storage: 256MB SLC NAND (Macronix MX30UF2G18AC)
* Ethernet:
	* 5x 1G RJ45 ports via QCA8337 switch
	* 3x 1G RJ45 ports via internal switch (QCA8075 PHY)
	* 1x 10G RJ45 via internal switch (AQR113C PHY)
	* 1x 10G SFP+ slot via internal switch
* WLAN:
	* 2.4GHz 4x4
	* 5GHz 8x8
	* 8 external antennas
* USB: 2x USB 3.0 Type-A
* Buttons:
	* Power switch
	* WPS
	* Reset
	* Wireless ON/OFF
	* LED ON/OFF
LED-s:
	* Power
	* Wi-Fi
	* WAN
	* 10G
	* SFP+
Power:
	* 19.5V via DC jack

Installation instructions:
--------------------------
1. Flash temporary OpenWrt initramfs:
* Flash openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx
via the stock firmware.
Administration -> Firmware Upgrade -> Manual Firmware update (Upload)

After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.

2. Sysupgrade from OpenWrt initramfs:
* Copy openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to
/tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin of
the running initramfs image.
* Simply sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin

After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.

Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-07-09 12:33:17 +02:00
Robert Marko
19ecf84f0f qualcommax: ipq807x: enable QCA83XX PHY driver
Asus RT-AX89X has an external QCA8337 switch that has built-in
internal ethernet PHY-s that are supported by the QCA83XX PHY driver so
lets enable it.

Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-07-09 12:33:17 +02:00
Robert Marko
b215f5c95e qualcommax: ipq807x: enable qca8k driver
Asus RT-AX89X has an Qualcomm QCA8337 switch used to provide additional
1G copper ports, so lets enable qca8k in order to utilize DSA instead of
relying on SSDK for it.

Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-07-09 12:33:17 +02:00
Robert Marko
c39c8da242 qualcommax: ipq807x: enable GPIO bitbanged MDIO
Asus RT-AX89X is using GPIO bitbanged MDIO on newer HW revisions, so lets
enable it in kernel config.

Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-07-09 12:33:17 +02:00
Robert Marko
157a33402d qualcommax: ipq8074-ess: move switch to ess-instance node
It seems that newer SSDK is now expecting the switch node to be a subnode
of "ess-instance" node which also contains "num_devices" as the number of
switches as you can also have external switches connected.

Asus RT-AX89X is even more peculiar as its bootloader has a hardcoded path
to enable if on that revision there is an AQR113 connected to port 6 of the
switch.

So, lets move the current switch node under ess-instance as otherwise it
seems that SSDK is having some issues parsing the UNIPHY mode properly as
I am getting the following:
[    6.981404] _adpt_hppe_instance1_mode_get[3275]:ERROR:port 6 doesn't support port_interface_mode 9

Which should not happen as that port has the mode set to 13.

Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-07-09 12:33:17 +02:00
Christian Marangi
2bae9d04af
qualcommax: ipq807x: fix build error with no initramfs for RAX120v2
Exclude additional initramfs image for Netgear RAX120v2 when no
initramfs image are compiled to fix build error.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-07-08 13:23:26 +02:00
Christian Marangi
f8cb39183d
qualcommax: fix RAX120v2 PWM Fan controller wrong definition
Fix RAX120v2 PWM Fan controller wrong definition by using a non-existant
kmod and using the wrong compatible for it enabling an external clock
while actually the device use an internal one.

Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-06-25 12:52:44 +02:00
Robert Marko
a47650e4cb qualcommax: get rid of custom socinfo.h header
Now that SSDK has been updated to use in-kernel SMEM ID-s to identify
the SoC its running on instead of relying on the downstream socinfo.h
header we can move the read_ipq_soc_version_major() function directly to
cpr3-util.c as its the only user of anything from the header and drop it.

Link: https://github.com/openwrt/openwrt/pull/15786
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-23 23:09:54 +02:00
Rosen Penev
6ff598306f
treewide: gpio to gpios
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property

Used git grep -E $'\tgpio = <' to make the changes.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-06-17 12:57:06 +02:00
Andrew Smith
9745de82d5 qualcommax: ipq807x: use ath11k_patch_mac for SXK80
Use ath11k_patch_mac and ath11k_set_macflag functions for SXK80

Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15732
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-17 12:35:07 +02:00
Chukun Pan
0a76244a72 qualcommax: ipq807x: fix sysupgrade for ZBT-Z800AX
This router has two rootfs partitions and dualboot is used.
Vendor firmware may swap the rootfs partition location, u-boot append
'ubi.mtd=rootfs' in the end of cmdline. Since we use fixed-partitions,
force boot from the first rootfs partition to avoid boot failure.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15700
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-13 18:01:03 +02:00
Kristian Skramstad
75a76355cb qualcommax: ipq807x: wax620 and wax630: fix wifi mac address
The wifi radios on wax620 and wax630 got a random mac
address on boot. So fix this by using ath11k_patch_mac
and give a static mac address from label-mac-device.

Tested and working on wax620 and wax630.

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15597
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-13 11:01:59 +02:00
Chukun Pan
29faf53b8c qualcommax: use ath11k_patch_mac for ZBT-Z800AX
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 13:15:48 +02:00
Andrew Smith
0f5c28b96b qualcommax: ipq807x support Netgear Orbi Pro SXK80
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)

Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
    - 2.4 GHz: Qualcomm QCN5024 4x4
    - 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
    - Power: (Green and red)
    - Front: (Blue, green, red and white)
* Buttons:
    - 1x Soft reset
    - 1x Sync/WPS
* Power: 12V DC Jack

Installation instructions (Telnet):
-----------------------------------

*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate

1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:

`fw_setenv bootcmd 'env default -a; saveenv; reset'`

5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.

6. Run the following command:

`fw_printenv`

It should look similar to the below:

```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```

**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**

7. Run the following command:

`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`

(This should match what's in the bootcmd variable displayed in step 6)

8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```

9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.

10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1

11. Once OpenWrt has booted, update the bootcmd using the following command:

`fw_setenv bootcmd 'run wrtboot'`

12. Flash the sysupgrade image

13. It should boot into OpenWrt

References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip

Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-22 14:51:36 +02:00
Robert Marko
cd9241db23 qualcommax: ipq807x: sax1v1k: fix QCA8081 reset
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.

Setting an deasset delay seems to fix this, so lets set it.

Fixes: 
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-21 20:15:03 +02:00
Paweł Owoc
9bdaebaff3 qualcommax: ipq807x: add support for Linksys MX8500
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset

Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel

5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Paweł Owoc
7f1c87ebde qualcommax: ipq807x: define common Linksys MX device
Define common Linksys MX device for MX4200v1/v2 and MX5300.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Paweł Owoc
b32a17e82d qualcommax: ipq807x: Remove unused gpio from QPIC pins
Remove gpio16 from the default NAND pinctrl configuration
as its unused and only needed for LCD.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Isaev Ruslan
be37ab6e51 qualcommax: ipq807x: uboot-envtools: yuncore ax880
There was no config in the uboot-envtools package, so there is no
generated /etc/fw_env.config for the fw_printenv and fw_setenv utils.
Since uboot-envtools 2024.01, there is a way to make these utils work
without /etc/fw_env.config if the DT has an env partition with the prop.:

compatible = "u-boot,env";

So, this commit adds the prop. above to the appsblenv:0 partition
in the yuncore ax880 DTS file.

Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15305
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-30 13:51:15 +02:00
Christian Marangi
284735246c
qualcommax: ipq60xx: mute warning on bootcount enable compile
ipq60xx bootcount script include /lib/functions that produce warning
when the script is enabled on image compilation. This script is already
included by /etc/rc.common hence it's not needed.

While at it also fix the format of the switch case.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-29 21:54:39 +02:00
Ulrich Stark
7cb161ae84 qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
For this particualar device we get random MAC's for Wifi on each (re-)boot.
This is because art partition/pre caldata do not contain valid MAC addresses.

As we have now a new/better approach with ath11k_patch_mac we can use it for
this device too.

I'm using this approach for like two weeks and its working flawlessly.

Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>

qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
Changing order to 3/phy0/5G-1, 2/phy1/2G, 4/phy2/5G-2.

Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
2024-04-27 12:01:07 +02:00
Paweł Owoc
48daac25ce qualcommax: ipq807x: use ath11k_patch_mac for RAX120v2
Use ath11k_patch_mac and ath11k_set_macflag functions for RAX120v2 (pre-caldata does not contain valid MAC addresses)

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
2024-04-23 22:35:57 +02:00
Paweł Owoc
682393cd1a qualcommax: ipq807x: use ath11k_patch_mac and ath11k_remove_regdomain for MX4200
Use ath11k_patch_mac, ath11k_remove_regdomain and ath11k_set_macflag functions for MX4200
(only v2 variant requires MAC patching)

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
2024-04-23 22:35:57 +02:00
Connor Yoon
3569b37b15 ipq807x: add Spectrum SAX1V1K
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923

It continues the original work by @MeisterLone to get this device supported.

Specifications:
```
  •  CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
  •  RAM: 2048MB of DDR3
  •  Storage: 1024MB eMMC
  •  Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
  •  WLAN:
     • 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
     • 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate

  •  LED: 1 gpio-controlled dual color led (blue/red)
  •  Buttons: 1x reset
  •  Power: 12V DC jack
```

Notes:
```
  •  This commit adds only single partition support, that means
     sysupgrade is upgrading the current rootfs partition.
  •  Installation can be done by serial connection only.
  •  A poulated serial header is onboard
     https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
  •  RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```

Installation Instructions:

	**Most part of the installation is performed from an initramfs image.**

	Boot initramfs : Using serial connection
	1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
	2. Once that message appears,
	    login with username 'root'
	    password serial number of your router in uppercase.
	3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
	    https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
	4. chmod 755 open.sh
	5. ./open.sh
	6. Set your ip to 192.168.0.1
	7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
	8. Reboot device. On boot it will try TFTP.

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Flash firmware: sysupgrade
	   # sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
	4. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
	5. Reboot the device
	   # reboot
	6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
	    Factory Reset is MUST required
	    # Once serial console is displaying to login, hold reset button for 10 sec
	7. Now everything should be operational.

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Connor Yoon <j_connor@taliaent.com>
2024-04-23 21:48:34 +02:00
Chukun Pan
9cef2bc224 ipq807x: add support for Zbtlink ZBT-Z800AX
Hardware specifications:
  SoC: Qualcomm IPQ8072A
  RAM: 1GB of DDR4 600MHz
  Flash1: Winbond W25Q64DW 8MB
  Flash2: MX30UF2G28AD 256MB
  WiFi1: QCN5024 2.4GHz AX 4x4
  WiFi2: QCN5054 5GHz AX 4x4
  Ethernet: 5x 1G RJ45 port
  USB: 2x USB 3.0 (1x M.2)
  Button: Reset, WPS

Flash instructions:
  Upload factory.bin in stock firmware's
  upgrade page, do not preserve settings.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-04-17 12:08:56 +02:00
Sean Khan
849ebc905b qualcommax: enhance smp_affinity (log, uci, syntax)
1.) Changed logic of `set_affinity` to now use physical cores rather than
    knowing the bitmask. Rather than having to know a bitmask, users can
    provide a numerical instance of one or more CPU cores
    (numbered 0-63).

    This is done via function `cpus_to_bitmask`.

    Functions Added:

    a.) bitmask_to_cpus - Takes a bitmask of CPUs and returns a
         list of CPU numbers. (i.e. `bitmask_to_cpus "f"` -> 0,1,2,3)

    b.) cpus_to_bitmask - Takes a comma/space or range list of CPUs and returns
         a bitmask.

         Example:
         `cpus_to_bitmask "2,3"`     -> c
         `cpus_to_bitmask "0,1,2,3"` -> f
         `cpus_to_bitmask "1,3"`     -> a

         With or without quotes
         `cpus_to_bitmask "1 3"`     -> a
         `cpus_to_bitmask  1 3`      -> a

2.) Added UCI options:

    enable     - to enable/disable the script from running.   [default 1 (on)]
    enable_log - to enable/disable logging output to `logger`.[default 1 (on)]

    Log output:
```
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(87) reo2host-destination-ring1    to CPU 0
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(88) reo2host-destination-ring2    to CPU 1
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(89) reo2host-destination-ring3    to CPU 2
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(90) reo2host-destination-ring4    to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(79) wbm2host-tx-completions-ring1 to CPU 1
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(83) wbm2host-tx-completions-ring2 to CPU 2
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(85) wbm2host-tx-completions-ring3 to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(73) ppdu-end-interrupts-mac1      to CPU 1
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(77) ppdu-end-interrupts-mac2      to CPU 2
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(75) ppdu-end-interrupts-mac3      to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(32) edma_txcmpl                   to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(33) edma_rxfill                   to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(35) edma_rxdesc                   to CPU 3
    Mon Apr  8 23:00:01 2024 user.notice smp_affinity: Pinning IRQ(36) edma_misc                     to CPU 3
```

    Output of `/proc/interrupts`:
```
 69:          0          0          0          0 GIC-0 209 Edge      rxdma2host-destination-ring-mac1
 70:          0          0          0          0 GIC-0 211 Edge      rxdma2host-destination-ring-mac3
 71:          0          0          0          0 GIC-0 210 Edge      rxdma2host-destination-ring-mac2
 72:       2435          0          0          0 GIC-0 321 Edge      reo2host-status
 73:     268427       8011          0          0 GIC-0 261 Edge      ppdu-end-interrupts-mac1
 74:          2          0          0          0 GIC-0 255 Edge      rxdma2host-monitor-status-ring-mac1
 75:     176169          0          4      10035 GIC-0 263 Edge      ppdu-end-interrupts-mac3
 76:          2          0          0          0 GIC-0 260 Edge      rxdma2host-monitor-status-ring-mac3
 77:          0          0          0          0 GIC-0 262 Edge      ppdu-end-interrupts-mac2
 78:          0          0          0          0 GIC-0 256 Edge      rxdma2host-monitor-status-ring-mac2
 79:       3428       3123          0          0 GIC-0 189 Edge      wbm2host-tx-completions-ring1
 80:          0          0          0          0 GIC-0 323 Edge      reo2ost-exception
 81:        178          0          0          0 GIC-0 322 Edge      wbm2host-rx-release
 82:          0          0          0          0 GIC-0 212 Edge      host2rxdma-host-buf-ring-mac1
 83:       6524          0      13712          0 GIC-0 190 Edge      wbm2host-tx-completions-ring2
 84:          4          0          0          0 GIC-0 235 Edge      host2rxdma-host-buf-ring-mac3
 85:        560          0          0       1979 GIC-0 191 Edge      wbm2host-tx-completions-ring3
 86:          0          0          0          0 GIC-0 215 Edge      host2rxdma-host-buf-ring-mac2
 87:       4520          0          0          0 GIC-0 267 Edge      reo2host-destination-ring1
 88:       2231       2811          0          0 GIC-0 268 Edge      reo2host-destination-ring2
 89:       2180          0       2512          0 GIC-0 271 Edge      reo2host-destination-ring3
 90:       1990          0          0       2321 GIC-0 320 Edge      reo2host-destination-ring4
```

3.) Added `uci-defaults` script `15_smp_affinity` to configure defaults
    options on first boot.

Signed-off-by: Sean Khan <datapronix@protonmail.com>
2024-04-12 13:22:12 +02:00
Robert Marko
076f945dfb qualcommax: drop 6.1 support
We have defaulted to 6.6 for a while so its time to completely drop 6.1
so new devices dont have to include patches for 6.1.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-11 17:26:47 +02:00
Sean Khan
d606b84c4e qualcommax: Skip compiling unnecessary dtbs
Currently the compile phase of the kernel builds `Image dtbs modules`.
However, none of the dtbs that get built are used for the final image.

This ends up unnecessarily taking CPU cycles and produces a lot of
`WARNINGS` that can lead users to believe there's cause for concern. I
believe the same principle can be applied to other targets.

```
DTC     arch/arm64/boot/dts/qcom/msm8996-mtp.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])

DTC     arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])

DTC     arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])

DTC     arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])

DTC     arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])

DTC     arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])

DTC     arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dtb
arch/arm64/boot/dts/qcom/msm8996.dtsi:2954.36-2962.5: Warning (clocks_property):
/soc/clock-controller@6400000: Missing property '#clock-cells' in node
/soc/mailbox@9820000 or bad phandle (referred from clocks[2])
```

Signed-off-by: Sean Khan <datapronix@protonmail.com>
2024-04-08 16:24:12 -04:00
John Audia
5c2eca676a kernel: bump 6.6 to 6.6.24
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.24

Removed upstreamed:
	generic/backport-6.6/838-v6.9-leds-trigger-netdev-Fix-kernel-panic-on-interface-re.patch[1]
	generic/backport-6.6/981-mtd-spinand-Add-support-for-5-byte-IDs.patch[2]
	mediatek/patches-6.6/831-thermal-drivers-mediatek-Fix-control-buffer-enablement-on-MT7896.patch[3]

Removed:
	ipq40xx/patches-6.6/110-mtd-limit-OTP-nvmem-to-non-nand-devices.patch[4]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.24&id=10f2af1af8ab8a7064f193446abd5579d3def7e3
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.24&id=9c74507e6c4382d12a5e418742b81fd441f03313
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.24&id=fe750e2744428be6aec7395b13df3b34381ce6b6
4. Acknowledgment to @DragonBlurp for pointing out the redundancy of this patch. dd78a59cd7

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-04-05 14:43:44 -04:00