Commit Graph

48956 Commits

Author SHA1 Message Date
Adrian Schmutzler
0b1cdb7eea treewide: remove empty default cases
There is no apparent reason to have an empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:46:19 +02:00
Adrian Schmutzler
a744c14dfa ipq806x: sort entries in 02_network
Apply alphabetic sorting like in the other files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-17 12:33:45 +02:00
Rui Salvaterra
419f149e48 zram-swap: default to lzo instead of lzo-rle compression
On devices with small amounts of RAM, zram-swap fails to initialise due to the
default compression algorithm (lzo-rle). Startup example on an AirGrid M2, with
32 MiB of RAM:

root@airgrid:/etc/config# /etc/init.d/zram start
zram_start: activating '/dev/zram0' for swapping (13 MegaBytes)
zram_reset: enforcing defaults via /sys/block/zram0/reset
sh: write error: Out of memory
mkswap: image is too small
swapon: /dev/zram0: Invalid argument
root@airgrid:/etc/config#

Fix this by defaulting to traditional lzo, which works fine and is always
available.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-09-17 10:29:40 +02:00
John Crispin
0fbdb51f76 ipq40xx: add Edgecore OAP-100 support
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
  - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
  - ubiattach -p /dev/mtd0
  - ubirmvol /dev/ubi0 -n0
  - ubirmvol /dev/ubi0 -n1
  - ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
  - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin

Signed-off-by: John Crispin <john@phrozen.org>
2020-09-17 08:43:07 +02:00
Robert Marko
4488b260a0 ipq40xx: add Edgecore ECW5211 support
This patch adds support for the Edgecore ECW5211 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:43:03 +02:00
Robert Marko
59f0a0fd83 ipq806x: add Edgecore ECW5410 support
This patch adds support for the Edgecore ECW5410 indoor AP.

Specification:
- SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15
- RAM: 256MB(225 usable) DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB S34MS01G2 Parallel NAND
- Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn)
- CC2540 BLE
- UART console on RJ45 next to ethernet ports exposed.
Its Cisco pin compatible, 115200 8n1 baud.

Installation instructions:
Through stock firmware or initramfs.

1.Connect to console
2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe.
3. Transfer factory image
4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path>

This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0

Note

Initramfs:
1.  Connect to console
2.  Transfer the image from TFTP server with tftpboot,
or by using DHCP advertised image with dhcp command.
3. bootm
4. Run ubiformat /dev/mtd1

You need to interrupt the bootloader after rebooting and run:
run altbootcmd

This will switch your active rootfs partition to one you wrote to and boot from it.

So if rootfs1 is active, then it will change it to rootfs2.

This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0
If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those.
This will result in wrong ordering and OpenWrt will panic on boot.

5. Transfer sysupgrade image
6. Flash with sysupgrade -n.

Note that sysupgrade will write the image to rootfs partition that is not currently in use.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
43a53891ce ipq806x: import bootargs-append from IPQ40xx
This imports the patch that adds bootargs-append support from IPQ40xx.

This way we can append additional boot arguments from DTS instead of only being able to overwrite them.

This way dual firmware devices can use the rootfs number that bootloader passes to decide from what to boot.
But we still need to append console info and ubi root info.

This is used by Edgecore ECW5410.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
811af0d98a ipq806x: add GSBI1 node to DTSI
IPQ806x series also has a GSBI1 with UART and I2C peripherals, so lets add the node for it.

Its needed for Edgecore ECW5410 which uses the UART from GSBI1 as second UART for Bluetooth.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
6133ac8e99 ipq806x: 5.4: enable AT803X driver
Its needed for Edgecore ECW5410 which does not use QCA8337 switch,
but rather 2x AR8033 PHY-s directly connected to GMAC-s.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Robert Marko
179073b0cc firmware: ipq-wifi: enable use on IPQ806x
This enables the ipq-wifi package to be used on IPQ806x target.
Its needed for boards using a different BDF than one shipped in the upstream board-2.bin.

Currently needed for Edgecore ECW5410.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-17 08:42:17 +02:00
Aleksander Jan Bajkowski
4a46f36f99 lantiq: remove trailing whitespaces in dts
Remove trailing whitespaces in dts files.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-09-17 00:21:41 +02:00
Felix Fietkau
673062fc56 mac80211: allow bigger A-MSDU sizes in VHT, even if HT is limited
Improves tx throughput when connecting to some APs (e.g. Asus RT-AC88U)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-16 18:49:11 +02:00
Adrian Schmutzler
947bfc62d0 ath79: fix button types for WZR-HP-AG300H and WZR-600DHP
Router and Movie "keys" are actually switches for both devices
according to the manual. This has been properly implemented in ar71xx,
but overlooked when porting to ath79.

Fixes: 480bf28273 ("ath79: add support for Buffalo WZR-HP-AG300H")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:34:35 +02:00
Adrian Schmutzler
25f2f66eea ath79: add support for Buffalo WZR-600DHP
The hardware of this device seems to be identical to WZR-HP-AG300H.
It was already implemented as a clone in ar71xx.

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM
- 32 MiB Flash
- WiFi 5 GHz a/n
- WiFi 2.4 GHz b/g/n
- 5x 1000Base-T Ethernet
- 1x USB 2.0

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:32:12 +02:00
Adrian Schmutzler
c68105c3b4 ath79: use common device definition for Buffalo devices
The Buffalo devices in ath79 share their image generation code,
so let's create a shared Device definition for them.

Since most of them use BUFFALO_HWVER := 3, this is moved as
default to the shared definition as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:31:03 +02:00
Adrian Schmutzler
a99614a44f ath79: consistently use "info" label for default-mac partition
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like

  {"default-mac", 0x610000, 0x00020},
  {"pin", 0x610100, 0x00020},
  {"product-info", 0x611100, 0x01000},

In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.

However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.

While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.

Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:28:48 +02:00
Adrian Schmutzler
cb9bb908de base-files: drop default setup for vconfig
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.

While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.

Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.

[1] 899a23227e ("busybox: improve applets & deprecate ifconfig, route")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 17:28:20 +02:00
Adrian Schmutzler
300173950d rtl838x: fix incorrect assignment from kstrtoul in serial.c
Assign return value of kstrtoul to error variable instead of
conversion value.

Suggested-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 16:31:28 +02:00
Adrian Schmutzler
5c0cecb6c6 rtl838x: refresh config
Use "make kernel_oldconfig" to update and sort target config.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 16:31:28 +02:00
Adrian Schmutzler
0da0aab6f2 rtl838x: remove some debug output in rtl838x-nor.c
Seems like leftovers from development, remove them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-16 16:31:28 +02:00
Rafał Miłecki
4a3230683b uhttpd: update to the latest master
1172357 ubus: add new RESTful API
fe1888f ubus: fix blob_buf initialization

Fixes: 3d167ed805 ("uhttpd: update to the latest master")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-09-15 13:45:33 +02:00
Adrian Schmutzler
d5c4750a71 rtl838x: remove and add some empty lines
Do some minor empty lines cleanup, i.e. remove those at EOF and
add some for cosmetic reasons/consistency.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-15 12:28:43 +02:00
Jo-Philipp Wich
0b82ebaccb Revert "build: create tmp/userids file"
This reverts commit 34cc2c9a99.

The reverted shell code is a very poor reimplementation of the existing
package-metadata.pl usergroup subcommand and the resulting file is not
used anymore, so drop this code.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-14 17:11:06 +02:00
Jo-Philipp Wich
4038c031cb scripts: ipkg-build: simplify uid/gid resolving
Use the prepared .packageusergroup file to lookup user and group names
when processing the passed file mode.

Also replace the various subshell/cut invocations with a sequence of
standard variable interpolations which fixes paths with embedded colons
as a side-effect.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-14 17:11:04 +02:00
Jo-Philipp Wich
7a29e24dbb build: dump effective user/group id mapping to file
This file can be subsequently used to resolve symbolic user or group names
to their numeric IDs when packing ipk archives.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-09-14 17:01:44 +02:00
Paul Spooren
51ec51871f build: add user/group ID resolve function
With the introduction of `./tmp/userids` the `ipkg-build` script can now
resolve values of "PKG_FILE_MODES", allowing users to set names rather
than numeric values.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-09-14 10:54:52 +01:00
Paul Spooren
34cc2c9a99 build: create tmp/userids file
Multiple packages contain a USERID variable defining required user and
group for the package to run. With the recent addition of
"PKG_FILE_MODES" it is possible to define user and group of specific
files, replacing (possibly insecure) post-inst scripts. These modes are
set during build time and put directly into the packages.

To allow user and group names rather than the numeric values, a mapping
like `/etc/passwd` is required by the `ipkg-build` script, mapping names
defined in "PKG_FILE_MODES" to a numeric value, as the build system does
not create any users during build.

This commit adds a single line to the `prepare-tmpinfo` target, so that
everytime the feeds are updated the *passwd like* content of
`./tmp/userids` is updated.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-09-14 10:54:52 +01:00
Birger Koblitz
df8e6be59a rtl838x: add new architecture
This adds support for the RTL838x Architecture.
SoCs of this type are used in managed and un-managed Switches and Routers
with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash,
Ethernet including a DSA switch driver and internal and external PHYs used
with these switches.

Supported SoCs:

	RTL8380M
	RTL8381M
	RTL8382M

The kernel will also boot on the following RTL839x SoCs, however driver
support apart from spi-nor is missing:

	RTL8390
	RTL8391
	RTL8393

The following PHYs are supported:

	RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port)
	RTL8218B internal: internal PHY of the RTL838x chips
	RTL8318b external (QSGMII 8-port GMAC phy)
	RTL8382M SerDes for 2 SFP ports
	Initialization sequences for the PHYs are provided in the form of
	firmware files.

Flash driver supports 3 / 4 byte access

DSA switch driver supports VLANs, port isolation, STP and port mirroring.

The ALLNET ALL-SG8208M is supported as Proof of Concept:

	RTL8382M SoC
	1 MIPS 4KEc core @ 500MHz
	8 Internal PHYs (RTL8218B)
	128MB DRAM (Nanya NT5TU128MB)
	16MB NOR Flash (MXIC 25L128)
	8 GBEthernet ports with one green status LED each (SoC controlled)
	1 Power LED (not configurable)
	1 SYS LED (configurable)
	1 On-Off switch (not configurable)
	1 Reset button at the right behind right air-vent (not configurable)
	1 Reset button on front panel (configurable)
	12V 1A barrel connector
	1 serial header with populated standard pin connector and with markings
	  GND TX RX Vcc(3.3V), connection properties: 115200 8N1

To install, upload the sysupgrade image to the OEM webpage.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-14 07:54:30 +02:00
Birger Koblitz
7bb1bd469e kernel: add support for ALLNET devices in mtdsplit
Add support for uimage headers from ALLNET and provide support for the
SG8208M and SG8310PM devices' magic bytes.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-14 07:54:30 +02:00
Adrian Schmutzler
a9790dff53 cns3xxx: drop target
This target has not been updated to 5.4 yet, and the only person
trying it (Koen) decided to retreat based on the following reasons:

- The target is not DT-aware at all

- The huge amount of effort required

- The SoC itself reached EoL at Cavium for some time now

- Upstream removed some important parts as it's also slowly getting EoL
  over there

- The commercial product that used this will fade out shortly

- The amount of download for this binary suggest that the target is not
  that popular

Since nobody has picked up the work since then, and this is the last
remaining 4.19-only target, finally drop it now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-14 00:19:27 +02:00
Klaus Kudielka
04d3b517dc uboot-envtools: mvebu: update uci defaults for Turris Omnia
On the Turris Omnia 2019, u-boot environment is located at 0xF0000, instead
of 0xC0000. The switch happened with u-boot-omnia package version 2019-04-2
(May 10, 2019).

Check the installed u-boot release, and set the default accordingly.

Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
[bump PKG_RELEASE, use lower case for hex offset]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-13 13:56:47 +02:00
Chuanhong Guo
2188ef954e ramips: mt7621: pbr-m1: fix firmware size
This board is equipped with Winbond W25Q256FV 32M SPI-NOR.
Fix partition size for that.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-13 19:15:06 +08:00
Chuanhong Guo
8126521e11 ramips: mt7621: pbr-m1: increase SPI clock to 50MHz
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-13 18:53:25 +08:00
Chuanhong Guo
6f2c95f0cf ramips: mt7621: pbr-m1: add pcie reset for asm1061
this board has a pcie to sata bridge connected to pcie2 with a
separated pcie reset on gpio7.
add reset-gpios and corresponding pinctrl nodes into dts.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-13 18:49:26 +08:00
Felix Fietkau
f0cc5f6c0a ramips/mediatek: improve GRO performance, fix PPE packet parsing
Backport upstream changes to initialize GDM settings and reset PPE
Allow GMAC to recognize the special tag to fix PPE packet parsing
Improve GRO performance by passing PPE L4 hash as skb hash

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-13 11:14:32 +02:00
John Audia
17e64b9447 kernel: bump 5.4 to 5.4.65
All modifications made by update_kernel.sh/no manual intervention needed

Build-tested: x86_64
Run-tested: ipq806x (R7800)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2020-09-12 23:39:25 +02:00
Hans Dedecker
96586ad8ca netifd: update to latest git HEAD
55a7b6b netifd: vxlan: add aging and maxaddress options
11223f5 netifd: vxlan: add most missing boolean options
226566b netifd: vxlan: refactor mapping of boolean attrs
a3c033e netifd: vxlan: handle srcport range

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-09-12 21:29:20 +02:00
Sander Vanheule
c9f51a9ad6 ath79: support for TP-Link EAP225-Wall v2
TP-Link EAP225-Wall v2 is an AC1200 (802.11ac Wave-2) wall plate access
point. UART access and debricking require fine soldering.

The device was kindly provided for porting by Stijn Segers.

Device specifications:
* SoC: QCA9561 @ 775MHz
* RAM: 128MiB DDR2
* Flash: 16MiB SPI-NOR (GD25Q127CSIG)
* Wireless 2.4GHz (SoC): b/g/n, 2x2
* Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO
* Ethernet (SoC): 4× 100Mbps
  * Eth0 (back): 802.3af/at PoE in
  * Eth1, Eth2 (bottom)
  * Eth3 (bottom): PoE out (can be toggled by GPIO)
* One status LED
* Two buttons (both work as failsafe)
  * LED button, implemented as KEY_BRIGHTNESS_TOGGLE
  * Reset button

Flashing instructions, requires recent firmware (tested on 1.20.0):
* ssh into target device and run `cliclientd stopcs`
* Upgrade with factory image via web interface

Debricking:
* Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC)
    * Bridge unpopulated resistors R162 (TXD) and R165 (RXD)
      Do NOT bridge R164
    * Use 3.3V, 115200 baud, 8n1
* Interrupt bootloader by holding CTRL+B during boot
* tftp initramfs to flash via sysupgrade or LuCI web interface

MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From OEM ifconfig:
    br0       Link encap:Ethernet  HWaddr 50:...:04
    eth0      Link encap:Ethernet  HWaddr 50:...:04
    wifi0     Link encap:UNSPEC  HWaddr 50-...-04-...
    wifi1     Link encap:UNSPEC  HWaddr 50-...-05-...

Signed-off-by: Sander Vanheule <sander@svanheule.net>
[fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 19:37:24 +02:00
Zhong Jianxin
53df30f02b ath79: add support for Mercury MW4530R v1
Mercury MW4530R is a TP-Link TL-WDR4310 clone.

Specification:

* SOC: Atheros AR9344 (560 MHz)
* RAM: 128 MiB
* Flash: 8192 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
* Wireless:
  - 2.4 GHz b/g/n (internal)
  - 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0

Installation:

Flash factory image via OEM web interface.

Signed-off-by: Zhong Jianxin <azuwis@gmail.com>
2020-09-12 18:47:26 +02:00
John Audia
bee76f1bfa kernel: bump 5.4 to 5.4.64
Remove upstreamed patches:
 generic-backport
  701-v5.5-net-core-use-listified-Rx-for-GRO_NORMAL-in-napi_gro.patch

Manually merged:
 mediatek/patches-5.4
  0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch

All other modifications made by update_kernel.sh

Build-tested: ipq806x, lantiq/xrx200, mvebu, x86/64
Run-tested: ipq806x (R7800), mvebu (mamba, rango),
  lantiq/xrx200 (Easybox 904 xDSL), x86/64

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add community build/run tests to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:28:50 +02:00
Adrian Schmutzler
c4110a524e ramips: create common DTSI for Sunvalley Filehub devices
HooToo HT-TM05 and RAVPower RP-WD03 have almost identical hardware
(except for RAM size) and are from the same vendor (SunValley).

Create a common DTSI file for them.

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:25:10 +02:00
Adrian Schmutzler
b56b499948 ramips: fix baud rate for RAVPower RP-WD03
The baud rate for the RAVPower RP-WD03 is 57600, not 115200.

Since this is the default from mt7620n.dtsi, the chosen node can
simply be removed from the device DTS.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:43 +02:00
Adrian Schmutzler
3fc7860961 ramips: assign LEDs for RAVPower RP-WD03
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:

  Flashing Blue: System loading
  Solid Blue: System loaded
  Flashing Green: Connecting to the Internet
  Solid Green: Connected to the Internet

According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:30 +02:00
Adrian Schmutzler
77825f3cfe ramips: fix MAC address assignment for RAVPower RP-WD03
MAC assignment based on vendor firmware:

  2.4 GHz    *:b4   (factory 0x04)
  LAN/label  *:b4   (factory 0x28)
  WAN        *:b5   (factory 0x2e)

The previously used location 0x4000 for ethernet is actually empty.

Therefore, fix the ethernet MAC address and set it as label-mac-address.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:02 +02:00
Adrian Schmutzler
07aa858a73 ramips: fix partitions and boot for RAVPower RP-WD03
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.

To address this, use the lzma loader (loader-okli) to work around this
limitation.

The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.

Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:31:03 +02:00
Adrian Schmutzler
a4e5b8897a ramips: use proper name for RAVPower RP-WD03
The proper model name is RP-WD03 (i.e. with the RP- prefix).

Adjust all names to that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:18:54 +02:00
Adrian Schmutzler
14024f6e0f kernel: use proper upstream inclusion version for patch
The patch is only included in kernel 5.5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 18:40:44 +02:00
Adrian Schmutzler
4527f59428 ramips: move ravpower-wd009-factory recipe to mt76x8.mk
The recipe is only used for a single device, so put it in the
subtarget file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 18:40:44 +02:00
David Bauer
2e6c236abd ipq40xx: essedma: enable VLAN tag offload for single-port
Enable the VLAN tag offloading mechanism for RGMII single-port devices.
This allows those devices to use 802.1Q VLANs on the ethernet port.

Previously, RX frames were double tagged, as the RX TAG removal flag was
not enabled and an additional 802.1Q header was inserted elsewhere in
the code.

On the TX side, tagging was completely not present for single-port
devices. Enable tagging if an 802.1Q frame should be transmitted and
disable the default tagging mechanism for single-port devices.

Tested on Aruba AP-303

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 17:37:11 +02:00
David Bauer
e289f18347 hostapd: add support for per-BSS airtime configuration
Add support for per-BSS airtime weight configuration. This allows to set
a airtime weight per BSS as well as a ratio limit based on the weight.

Support for this feature is only enabled in the full flavors of hostapd.

Consult the hostapd.conf documentation (Airtime policy configuration)
for more information on the inner workings of the exposed settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 17:35:48 +02:00