Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47851
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.
This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.
This results for a BTHOMEHUBV5A into the following led configuration:
- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"
With the final result of a switched off power led after boot.
The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47850
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47793
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47783
This patch adds the posibility to config the led behaviour of the lantiq phys
over the devicetree bindings.It patches the 0023-NET-PHY-adds-driver-for-lantiq-PHY11G
for 3.18 and 4.1. I have also added a register description overview for
applicable values. This goes to the documentation folder in the linux kernel.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 47566
This patch improves the default configuration of DWC2 on lantiq SoCs
somewhat:
* Set maximum packet count to largest allowed value by the DWC2 (511)
* Use 16-bit DMA bursts
* Divide fifo buffers more evenly
Default fifo buffer sizes from original ltq-hcd driver seem really
irrational. For example according to DWC2 data book rxfifo size of 240
will not fit even a single full length USB packet. On the other hand
non-periodic tx fifo size of 240 is more than enough to fit one complete
packet.
Change the sizes around to improve the situation and to fix some issues
especially with isochronous USB transfers.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 47563
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47254
Whenever two processes were executing different commands at the same
time then one of the commands sometimes got the response of the other
command.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47213
This should help finding potential problems with the SPI driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47209
Until now the SPI driver used the TX bits for the RX FIFO. This seems
uncritical for now since both are equals on my devices (VR9), but this
could cause problems on other SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47208
This reverts commit 68c2e4789b4f071ee75d39248f4d08fe8283eb28.
commit r47159 was bad
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47207
This patch fixes a wrong non pre-emptive crc errors output of
dsl_control.sh status.
Signed-off-by: Luca Debernardi <luca.debernardi@gmail.com>
SVN-Revision: 47172
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47130
Port of r41856.
In contrast to the brcm63xx target, it isn't sufficient to enable/disable
the bridge. The device needs to be enabled/disabled to fix the hang. The
bridge will be automatically enabled by the time the connected device is
enabled.
Fixes boot on TD-W8980.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47129
This adds the changes from r46219 to the linux 4.1 patches as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47128
As explained in recent sysupgrade/nand.sh commits, current NAND
sysupgrade is a bit misleading because of nand_do_platform_check
behavior. It leaves a special mark in /tmp/sysupgrade-nand-path
triggering some diffent code path in nand_upgrade_stage1.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
Please note that because of current nand_upgrade_stage1 implementation
this patch doesn't change any behaior yet. It only prepares lantiq
target for changing nand_do_platform_check (it will be possible after
preparing all other targets as well).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46939
Add AR9 DTS definition to be recognized by the DWC2 driver.
The same driver parameters can be mostly used except that some boards
seem to erroneously report OTG HNP/SRP capability of the USB HCD.
Forcing the HNP/SRP off allows these boards to work with the DWC2 as well.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46915
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.
Here are the DTS definitions which make it compatible with the DWC2
driver.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46914
Based on the ltq-hcd driver the AR9 USB can be initialized the same way
as the VR9 platform. Use the same initialization bits for both
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46913
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).
Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46869
Support for lantiq_svip_be has been removed a while ago, so EASY33016
images weren't buildable anymore. Remove the recipes as well as gzip
compressed kernel support, as EASY33016 was the last user of it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46760
The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's
PHY driver (for his u-boot sources) already supports that PHY because
it uses a PHY ID mask of 0xfffffff8.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46670
Instead of each target defining it the same, move the KDIR_TMP
definition to include/image.mk. In addition Image/Build/SysupgradeNAND
already requires KDIR_TMP to be set, so it makes sense to have it
globally defined.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46592
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.
Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46564
This ports 9e2a7b779e6f0914395da3657b00f0ac00209bfd to the 4.1 patches.
I forgot this when preparing the initial 4.1 patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46453
Basically the only error I am seeing is "Correctable Error". Also newer
lantiq PCIe drivers have this message wrapped in a "if debug enabled"
block. So it should be safe to disable this warning.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46222
Newer DSL driver versions depend on the address information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46221
Make it consistent with the net_device struct and the xrx200 driver
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46219
All (still relevant) patches were refresh.
The following patches were dropped because they are applied upstream:
- 0003-MIPS-lantiq-handle-vmmc-memory-reservation.patch
- 0005-MIPS-lantiq-add-reset-controller-api-support.patch
- 0006-MIPS-lantiq-reboot-gphy-on-restart.patch
- 0009-MIPS-lantiq-command-line-work-around.patch
- 0010-MIPS-lantiq-export-soc-type.patch
- 0011-lantiq-add-support-for-xrx200-firmware-depending-on-.patch
- 0037-MIPS-lantiq-move-eiu-init-after-irq_domain-register.patch
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46216
This also adds the old hardcoded value to the VGV7519BRN profile to make
sure that images are still generated correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45882
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45868
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45718
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45717
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44676
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44675
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44674
Port gpio code from original ltq-hcd driver to dwc2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44673
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.
This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44672
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44451
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44450
This adds a patch to target/linux/lantiq/patches-3.14
fixing a bug clock code on ar9. The current version returns
the wrong value for the fpi clock frequency in some
cases.
See discussion for further details:
https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html
I'm not sure about the patch naming and numbering convention.
Do please let me know it this is not OK.
Many thanks,
Ben Mulvihill
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 44083
This patch builds on the previous three to streamline support for the
Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44032
It seems the call to ltq_get_eth_mac() disappeared at some point. This
patch puts it where it currently most makes sense.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44031
Currently this initscript fails if the macaddr has any leading zeroes.
This patch corrects the problem.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44029
lantiq_dsl.sh didn't work with VDSL chipsets for now, fix that by
detecting whether vdsl_cpe_control or dsl_cpe_control should be used.
Also add missing quotes around shell string comparision.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43101
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43047
The installation process on nand-based boards using ubi
like the BTHOMEHUBV2B makes use of a ramdisk image, so it
makes sense to generate this by default.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42920
fix inclusion of functions.sh in dsl_fs init script
without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
SVN-Revision: 42575
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.
Many thanks,
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42316
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.
This was the one thing missing from r41474 for sysupgrade board
detection to work properly.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41567
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.
I'll leave the equivalent patch for xrx200 to someone who has a
board to test.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41565
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41474
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.
These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41449
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.
If anyone else is using jffs2_nand on a lantiq target please speak
up!
Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41312
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41310
At the moment, an rootfs.ubi is copied over to bin/lantiq
but rootfs-overlay.ubi is not. This adds it.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41270
This patch adds factory image building for the DGN3500, all variants,
and fixes sysupgrade images to make them play nice with the sercomm
secondary boot loader.
The factory images can be used directly in the update dialog in the
interface of the stock firmware and via the special Sercomm bootmode
and a special windows flashing utility (allegedly present in the CD
that came with the device -- but it's also compatible with the NSLU2
Upgrade_207_XP utility.) The special bootmode can be activated by
turning the device on while holding the reset button pressed, then
releasing it when the power led starts blinking red and green. Please
notice that if using the 207 utility, it will always report that the
flashing failed even though it completed successfully. Just power
cycle the router manually after the utility reports the failure and
OpenWRT will boot. This same utility (despite reporting failure in
this case too) can revert a DGN3500 (any variant) to the appropriate
stock Netgear firmware.
This patch is a heavily modified version of a package I found on the
OpenWRT forum with a couple fixes and features added -- mainly the
generation of all the different image variants to support all known
models directly, atm known variants are AnnexA-WW, AnnexA-NA and
AnnexB-DE/GR.
I tested the patch successfully on my device.
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 41236
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41214
ath5k fix in wifi and ethernet eeprom handling patch.
Without the line that adds the patch of_ath5k_eeprom_probe cause a
kernel panic, at least with the ARV4518PW.
Tested only in the modem-router mentioned above.
This patch is based in Bruno's hack present in patch #5454.
Signed off by: Bruno Rodríguez <bruno.rodriguez.1980@gmail.com>
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40999
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
The total ethernet frame length should be written to the hardware
register LTQ_ETOP_IGPLEN instead of just the value of the MTU. This
patch fixes network issues on various Danube boards, especially when
VLAN tagging is enabled.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40541
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40495
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
this should really be auto detected by the kernel, lets used this workaround until the real
solution is ready
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40418
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40329
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.
Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.
v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
SVN-Revision: 40328
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to another partition called 'rootfs' being created
which would not be properly distinguished in the current user-space
code.
While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make
that configurable, the lack of users of brnboot and the fact that we
can freely decide the partition name made me simply change the
hard-coded string constant from "rootfs" to "firmware".
(I'm going to add support for ARV7506PW which run brnboot and needs
this change)
SVN-Revision: 40324
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40317
Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40312
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39587
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 39230
The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 38673
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37712
This is a really ugly hack but it will have to do until we copy the ramips patches to the lantiq tree
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37539
This patch enables retrieving the wifi calibration data from an MTD partition.
Try to copy mac address from ethernet before generating a random one.
This fixes DGN3500 ath9k support.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 37087
Trying to load the DEU modules results in unresolved symbols. This
provides them. This requires the previous patch to be applied first.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37086
This patch sets the cflags -mtune=34kc -mdsp only in XWAY subtarget, while the others remain with mtune=mips32r2.
Although the Danube has a Mips 24KEc core performs well with the above cflags.
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 37006
Set mips16 support in XWAY subtarget.
This patch is based in changeset #36600
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37005
Fix EBU leds by removing req2 and gnt2 from pinmux.
Fix rfkill button gpio.
Enable reset button.
Fix power led activation status.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 37004
Use platform data array for storing ath5k EEPROM instead of creating another one.
EEPROM size is 2048 words (2 bytes), so we must read 4096 bytes from flash.
No need to keep the checksum fix now that the EEPROM is loaded completely.
Add a manual eeprom swap for ath9k and keep the endian way.
Use mac-offset property retrieved from the DTS.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36901
Seems the existing kernel config for 3.8 was cp'ed from 3.7; this patch
is the result of "make kernel_oldconfig" with defaults for new options.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36900
This provides a boot LED sequence suitable for devices with both red and
green LEDs for power. This assumes no "default-on" settings in the
device tree.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36899
submitter was informed of a endinaess swap regression and replied with "works on my board"
revert the patch and make arv7518 wifi work again
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36807
The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
SVN-Revision: 36783
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36782
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
This patch enables retrieving the wifi calibration data from an MTD
partition. It requires the previous patch.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36779
This postpones the initialization of PCI and wifi until after the MTD
initialization, so that calibration data may be loaded from there.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36778
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36777
this adds basic support. the bootloader on these units is locked down.
until we have a replacement we can do basic testing with these env variables in uboot.
set update_openwrt erase 0xb0020000 0xb073ffff \;tftp 0x81000000 openwrt-lantiq-xway-VG3503J-squashfs.image\;cp.b 0x81000000 0xb0020000 \$(filesize)
set bootcmd cp.b 0xb0020000 0x80002000 0x400000\; go 0x80002000
unfortunatley the bootloader ignores the bootcmd, so autobooting is not possible yet. you need to call "run bootcmd" by hand after each power cycle.
please note that the vdsl firmware is non redistributable. you can find it in the GPL drop that BT provides.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36315
EEPROM is an actial serial EEPROM on the WiFi module, therefore we can remove
ralink_eep from the dts.
USB power-enable GPIO turned out to be GPIO #3 (found via probing/brute-force).
PCI works with default settings as long as the vendor bootloader is used.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 36030
This patch disables the execute-in-place (XIP) support for flash on
lantiq. This has to be disabled since the bus which flash is connected
to does not support unaligned accesses. Resolves data bus errors on
Lantiq routers with Intel command set flash.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 35992
user-space support for extracting the EEPROM for the RaLink WiFi is still
missing. Besides this, it's all working.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 35990
This patch correctly fixes USB on Lantiq ARV7518.
There was a failed attempt on fixing this on r35077 (https://dev.openwrt.org/changeset/35077/).
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 35354
Add ath9k eeprom and pci fixup support (again) for linux 3.7.
On linux 3.3, the fixup forced the regdomain to 0x67, causing low TX power.
This patch only corrects checksum, the rest of the EEPROM isn't changed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 35353
There are two different versions of SMC7908A-ISP: R01 and R01A.
R01 has an internal clock for PCI, meanwhile R01A has an external clock.
This fixes: https://dev.openwrt.org/ticket/12884
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 35352
Tested only on the wbmr-hp-g300h, could affect/break other devices.
Signed-off-by: Sebastian Mayr <sebastian.mayr@student.uibk.ac.at>
SVN-Revision: 34837
This patch fixes the GPIO ALTSEL settings for some of the GPIOs used by the PCI subsystem in Lantiq Danube. These changes are required for more than one PCI device to work. Tested with an ARV7510PW having two PCI-devices; a VIA USB controller and a Ralink WLAN mini-PCI card.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 33054
The ARV4525 board init is passing the wrong offset to
arv_register_ath5k() resulting in a bogus mac.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 32993
WIFI eeprom:
As discussed, it is impossible for nand and spi flash platforms to have the eeprom data available from mtd. I suggested to load the eeprom from user-space. I've looked into regular firmware loading but this is only possible when using modules. I've created a sysfs entry that allows reading and writing the eeprom data to the platform data. After loading the eeprom data I rely on pci-hotplug support to disable the bogus pci device and rescan the bus (with fixups and all). Because hotplug is not available, an init script is created that performs the copy from mtd to platform data. I think it is best to eventually move the sysfs functions to dev_wifi_athxk.c file, this would get rid of the external to the ath9k platform data.
SPI flash:
It seems that the spi-xway driver is not really working. It causes my kernel to crash in all sorts of ways. I added to bitbang SPI to be able to the calibration data mention above.
I've kept the original mtd partitioning that Netgear uses.
Buttons/LED:
Both buttons are working properly. Two leds are not enabled: The red internet led is connected to the pci_gnt1 pin... I can't disable it because then DMA stops working.
The green wifi led is connected to an unknown atheros gpio.
Signed-off-by: Pieter Voorthuijsen <p.voorthuijsen at gmail.com>
SVN-Revision: 31910
moves the linux partition, removes the config partition and the
buttons settings have small adjustments.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 31909
The VLAN mapping on the ARV4520PW board is the following:
port on Router: | VLAN in software:
LAN 1 | 3
LAN 2 | 2
LAN 3 | 1
LAN 4 | 0
DSL | 4
So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.
SVN-Revision: 31391
A power-enable toggle gpio is not available, it is always on and protected with a resettable fuse.
Signed-off-by: Pieter Voorthuijsen<p.voorthuijsen at gmail.com>
SVN-Revision: 31205
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.
uboot environment config is used by fw_printenv fw_setenv tools.
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 30537
While the disadvantage is less available flash space, it's easy and
safe to flash without opening the device.
Going back to the original firmware is also possible.
This patch add two firmware utilities, mkbrncmdline and mkbrnboot.
mkbrncmdline patches the uncompressed kernel so the registeres a0 to
a3 are initialized and the memory size is passed in.
mkbrnboot takes the lzma compressed kernel and squashfs images and
creates a firmware image that can be flashed using the BRN-BOOT
recovery kernel, which is booted by holding both buttons when
powering up the device and will listen on http://192.168.2.1.
The firmware file from bin/lantiq/ to use is
openwrt-lantiq-danube-ARV4525PW-BRNDTW502-brnImage
The BRN-BOOT recovery kernel does size-check the image, so if it's
too big to fit into flash it will complain accordingly.
A second patch is needed to make the wired network interface work
since there is no u-boot to pre-initialise it.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 30532
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling
Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>
SVN-Revision: 29763
