Specification:
• 650/600/216 MHz (CPU/DDR/AHB)
• 64 MB of RAM (DDR2)
• 32 MB of FLASH
• 2T2R 2.4 GHz
• 2x 10/100 Mbps Ethernet
• 1x USB 2.0 Host socket
• 1x miniPCIe slot
• UART for serial console
• 14x GPIO
Flash instructions:
Upgrading from ar71xx target:
• Upload image into the board:
scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
root@192.168.1.1/tmp/
• Run sysupgrade
sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
Upgrading from u-boot:
• Set up tftp server with
openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin
• Go to u-boot (reboot and press ESC when prompted)
• Set TFTP server IP
setenv serverip 192.168.1.254
• Set device ip from the same subnet
setenv ipaddr 192.168.1.1
• Copy new firmware to board
tftpboot 0x82000000 initramfs.bin
• Boot OpenWRT
bootm 0x82000000
• Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into
the board
• Run sysupgrade.
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
New script for comgt. Should help to fetch balance or any additional information with USSD.
This script uses the standard AT command which should be supported by all modems.
Run-tested on: Mikrotik wAP LTE KIT
Signed-off-by: Kirill Lukonin <klukonin@gmail.com>
[fixed from/sob]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Module is needed for using iscsi-initiator userspace applications
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[added missing newline between kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Before this change, setting the verbosity to anything with V=blah would
cause uclibc++ build to print errors to the screen. Now, it the
clibc++ build verbosity will be altered in the following manners:
* V=s will set V=1 in the uclibc++ build
* V=sc will set V=2 in the uclibc++ build
Signed-off-by: Wren Turkal <wt@penguintechs.org>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds cpu frequency setting for AR724x and AR7161.
It is unknown if all the AR71xx devices support the same value range,
so support is only enabled for AR7161 at this stage.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The current code would return an error on ath79 when the SoC isn't known
to the driver. Return the raw hex value instead, as happens with non
supported targets.
Also return the correctly incremented value from
sc_tag_cpufreq_ath79_arraysize()
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
RouterBOOT cpu frequency settings are letter-indexed. Follow the
same logic for the sysfs interface.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
The routine would only accurately print out the first word.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
nand_release(&rbni->chip);
Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On a system python3 is linked to python3.6, fail to perform json_overview_image_info
and got `TypeError: __init__() got an unexpected keyword argument 'capture_output'`.
This patch emulate the behaviour on python 3.7+.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
This updates mconf.c readme message to maintain less changes with
upstream and consistency with nconf.c
Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
Add support for make target nconfig (ncurses)
Reviewed-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following build failures:
WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Upstream in commit 972d723484d8 ("split signkey_type and signature_type
for RSA sha1 vs sha256") has added strict checking of pubkey algorithms
which made keys with SHA-256 hashing algorithm unusable as they still
reuse the `ssh-rsa` public key format. So fix this by disabling the
check for `rsa-sha2-256` pubkeys.
Ref: https://tools.ietf.org/html/rfc8332#section-3
Fixes: d4c80f5b17 ("dropbear: bump to 2020.80")
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This moves WiFi LED triggers from 01_leds to device tree.
While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.
Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Only enable the testing-kernel feature for the target when the testing
kernel version does not match the stable kernel version.
This way, the option for building the testing kernel in the build config
menu is only exposed when there's a testing kernel available.
Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The removed lines are already included in vr9_avm_fritz736x.dtsi
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.
This fixed the following error reported by Luca Olivetti:
...
dwc2 1e101000.usb: DWC OTG Controller
dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
dwc2 1e101000.usb: irq 62, io mem 0x1e101000
dwc2 1e101000.usb: startup error -517
dwc2 1e101000.usb: USB bus 1 deregistered
dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517
Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Upstream commit 3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")
On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.
Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Add missing switch config (4 LAN-Ports + CPU).
Grey WAN port (used for ADSL) is not part of the switch.
Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).
Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).
Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
This can be useful when a DFS channel is configured, as the ACS channel
list is taken into account when switching channels after a radar event.
For example, this allows to prevent the SRD channels from being used in
that case.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[reorder structure]
Signed-off-by: David Bauer <mail@david-bauer.net>
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.
A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)
In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.
Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
* The only exception is ipq8064-db149, which defines
"serial0 = &uart2;", but inside a block called "alias" instead of
"aliases". It must be assumed that this is broken anyway, so we
don't touch it here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.
That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the DTSI files on ipq806x had a linear inheritance:
qcom-ipq8064.dtsi
v
qcom-ipq8064-v1.0.dtsi
v
qcom-ipq8064-v2.0.dtsi
v
qcom-ipq8065.dtsi
This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.
In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).
The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:
- Many definitions can be improved by just using the innermost labels.
- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
default and enabled where needed.
- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
the appropriate settings done in the lower DTSI files directly.
- For the opp_table0 adjustments for ipq8065, just redefine what's
changed, but don't add all the untouched properties again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.
* uart0_pins : Did not touch.
* i2c4_pins : This node seems to be not used at all in dts.
Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins : The common mux node is already present in the dtsi.
Removed the duplicate nodes from dts.
* nand_pins : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
There is one closing bracket too much.
Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set
Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.
With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.
Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.
Tested succesfully using a single Crucial BX500 SSD drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Run tested: ath79
Build tested: ath79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Build tested: ramips
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.
Fixes: FS#2928, FS#2899
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
Only collect arch_packages if actually generating any output.
Fixes: commit f09b9319 ("build,json: store arch_packages in profiles.json"(
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
