Both Y1 and Y1S have MT7612E wireless chip so I submitted this patch.
Tested on Lenovo Y1.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 44354
The ubootloader of the M2M sets the reset bits for
both USB device and USB host during initialization
(to save a few mA of power during boot).
However, for the usb<->sata bridge to be properly
detected, it is necessary to clear both reset bits
as otherwise the kernel logs will just be filled
with:
usb 1-1: device descriptor read/64, error -145
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44248
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43305
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43245
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 43231
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43201
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43117
Change list:
* add tx scatter gather function.
* add software rx vlan offload to let GRO work.
* add jumbo frame support. because use build_skb so max MTU is 3812.
* enable hardware tx vlan.
* enable GRO and remove LRO. because it can improve performance and can work on forwarding.
* enable/fix tx padding function.
* let napi handle tx clean up.
* support ethtool operation. now support message level, hardware status and coalesce.
* ethtool support use mdio to get phy status only on mt7620. need modify dts file and add phy info to support it.
Notes:
* build and test on rt2880, rt3052, rt3352, rt3662, rt5350 and mt7620a.
* TCP NAT performance improve. test with netperf.
- rt2880(gigabit) from 5x to 12x Mbps.
- rt3x5x from 6x to 94 Mbps.
- rt5250 from 5x to 8x Mbps.
- rt3662(gigabit) from 6x to 42x Mbps with GRO. 23x Mbps without GRO. 66x Mbps with jumbo frame.
- mt7620 still 94Mbps.
* TSO function not tested. because i don't have mt7620 with eco >= 5. and the hardware don't support to set MSS. it will have problem.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43108
0x8100000c vs 0x810000c0 int he pvc register this caused the cascade with an external mt7530 to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43104
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43047
[base-files] shell-scripting: fix wrong usage of '==' operator
normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.
this patch does not change the behavior/logic of the scripts.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42911
7Links PX-4885 (clones) can also be purchased with 8MB flash.
Creating images for these routers, use dtsi for common part
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 42892
