ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- USB: 1x 2.0
- UART:
- J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
In contrast to to-be-supported A1004ns, the A104ns has no usable
value in 0x1fc40 (uboot), so wan_mac needs to be calculated.
Also note that GPIOs for the LEDs really are inverted compared to
the A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[moved state_default to device DTS, reordered properties in wmac,
added comment about wan_mac and LED GPIOs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This increases SPI frequency from the relatively low 10 MHz to 40 MHz.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sdhci and i2c nodes were copy-pasted, but are not needed as
the device does not provide that functionality. Remove them.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This does several trivial DTS style improvements:
- Move device name compatible to DTS files (and fix compatible in
11acnas.dts)
- Remove xhci node as status is set to okay in mt7621.dtsi already
- 0x0 instead of 0x0000
- Simplify state_default node definition
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m
While at it, make some DT node labels consistent with the label
property.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Current OpenWrt MAC setup:
eth0 &rom 0xf100 :48
eth0.2 eth0+1 :49
wlan0 (5 GHz) &radio 0x8004 different OUI
wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0
Label MAC address corresponds to eth0 (ðernet).
No additional addresses found in hexdump of rom/radio.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.
Also change "0" to "0x0" in the same files for consistency.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This re-organizes the device-tree files for the Sercomm-manufactured
NETGEAR routers. They are now split into two different base-boards,
from which the respective model is extended.
This partially reverts commit c7842ceaaa ("ramips: reorganize DTSI
files for Netgear R devices"), which introduced inheritance between two
completely unrelated base-boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ASUS WL-330N(3G) and the Edimax RG21S had the
reset keycode assigned to the WPS button. This patch
changes all three devices to use KEY_WPS_BUTTON in
the hopes that this fixes unwanted restarts/
unexpected behavior from the users point of view.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch does the following:
- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address
Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-00040000: "devdata"
00040000-00050000: "devconf"
Power LED can be controlled by SoC GPIO. Add it in the dts leds node.
RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.
Fixes commit 3459013257 ("ramips: correct R6220 button flag")
Signed-off-by: David Bauer <mail@david-bauer.net>
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.
The GPIO status reads the following for no buttons pressed:
root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7 ( |wps ) in hi
gpio-8 ( |wifi ) in hi
gpio-14 ( |reset ) in hi
Signed-off-by: David Bauer <mail@david-bauer.net>
This moves shared code of the named devices into a common DTSI.
Remove setting status="okay" for &gpio0 as it's not disabled in
mt7620a.dtsi.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Based on Macronix MX25L3205DM2I datasheet this is maximum
supported speed.
Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, improved commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the
device's web interface or via nmrpflash.
The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.
MAC adresses:
5.0 GHz 0x8004 *:9a
2.4 GHz 0x4 *:9b
lan 0x28 *:9b
wan 0x2e *:9c
Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.
Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For some devices, the keys node is named "button". Change name to
match the rest of the target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reorganizes DTSI files for the Netgear R devices in mt7621
(and the WNDR3700 v5). It creates a common DTSI for all R (sercomm)
devices and distributes the remaining code in r6220.dtsi to R6220
and WNDR3700 v5.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups
The factory partition scheme for MAC addresses (verified on both devices):
0x4 : WiFi 2.4GHz (label_mac-9)
0x28 : unused
0x2e : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused
By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch does the following:
1. remove u-boot-env partition
Stock bootloader saves env variables at 0x80000 in flash,
and there is nothing stored at 0x30000.
By merging the partition "u-boot-env" with "u-boot",
the partition table becomes the same as used in stock firmware:
00000000-00080000: "Bootloader"
00080000-00100000: "Config"
00100000-00140000: "Factory"
00140000-07f80000: "Kernel"
2. fix LAN/WAN MAC addresses and provide label MAC address
Ethernet MAC addresses are stored in factory partition at:
0xe000: LAN (label_mac)
0xe006: WAN (label_mac+1)
3. fix LAN port order
WF-2881 LAN ports are in reverse order of switch ports.
4. fix WiFi LEDs
mt76 led nodes are added to make WiFi LEDs work.
On top of this, mt76 node names are changed to more generic ones,
and compatible strings are also added.
5. fix pinmux groups
uart3 and uart2 pins are used as button and led, but jtag pins are not.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.
Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for the ZBT WE1026-H, an outdoor AP with
support for adding an internal LTE modem. The detailed specs are:
* CPU: MT7620A
* 2x 10/100Mbps Ethernet (LAN port has passive PoE support).
* 16/32 MB Flash.
* 128/256 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slot (only USB2.0 bus).
* 1x SIM slot (standard size).
* 1x 2.4Ghz WIFI (rt2800).
* 1x button.
* 6x LEDS (4 GPIO-controlled).
* 1x micro-SD reader.
The following have been tested and working:
- Ethernet switch
- Wifi
- Mini-PCIe slot + SIM slot
- USB port
- microSD slot
- sysupgrade
- reset button
Installation and recovery:
In order to install OpenWRT the first time or ito recover the router,
you can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.
Notes:
* When binding the USB LED to a usbport, the LED is switched on all the
time due to the presence of an internal hub. Thus, it does not really
signal any USB-information.
* I only have the 32MB version and have only added support for this
device. However, the files are structured so that adding support for the
16MB version should be easy.
* Only the LAN port is accessible from the outside of the casing and LEDs
are not visible.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[rebased onto base-files split, minor style fixes, removed use of
USB led as power LED]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit makes the following changes to the WE1026 DTS-files:
* The parts that are unique to the -5G-version (LED and 5GHz wifi)
are moved to a separate file, so that WE1026.dtsi can be referenced also
by the DTS for the -H version.
* Use the generic "flash"-name for the spi-nor node.
* Add label MAC.
All changes have been tested on the WE1026-5G-16M and work fine. I.e.,
the device works as before the DTS-changes.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Mathias Kresin <dev@kresin.me>
Acked-by: Alex Maclean <monkeh@monkeh.net>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
[minor style fixes, rebased onto base-files split, remove obsolete
gpio-keys comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- CMIIT ID: 2019AP2581
- SoC: MediaTek MT7621
- Flash: 16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM: 128MiB DDR3 (ESMT M15T1G1664A)
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
INSTALLATION:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.
With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.
For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).
Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".
[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
This patch removes a phy0tpt trigger from the power LED, which
seems to have been added by mistake.
WiFi LEDs using phy0radio and phy1radio triggers are present and
used correctly.
Cc: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In mt7628an.dtsi, calibration data for wmac is already defined:
mediatek,mtd-eeprom = <&factory 0x0>;
Thus, this patch removes redundant entries of this property in
derived DTS files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When caldata locations are defined with mediatek,mtd-eeprom the
MAC address is automatically read from offset +4. Thus, specifying
that location explicitly is redundant.
This patch removes those redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.
On both routers the installation can be done also via SSH:
Note: The user/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
> scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
> mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
> reboot
Changelog:
v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release
Signed-off-by: Gabor Varga <vargagab@gmail.com>
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.
Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
While at it, add/remove newlines in keys and leds node where
necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.
This patch fixes them for the ramips target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:
wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)
It looks like the only valid MAC address on this device is at 0x28.
So, this patch changes setup to calculate addresses based on the
value at 0x28:
lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)
Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Previously only the power LED was working.
With this patch all leds except 5GHz are working.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[rephrased commit title, drop status property]
Signed-off-by: David Bauer <mail@david-bauer.net>
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.
This changes ZBT-WE1026-5G to also follow that scheme.
The patch moves some block to keep alphatical order.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Spelling of Zbtlink varies across image definitions and DTS files.
This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.
This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
- UART:
- J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware:
SoC: MT7621A
Flash: 32 MiB
RAM: 512 MiB
Ethernet: built-in switch
USB: 1x USB3.0
SATA: ASM1060, 1 SATA port
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.
Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.
Specification:
- Bootloader: U-Boot
- SoC: MediaTek MT7620A (600 MHz)
- Flash: 16MB, Macronix MX25L12845E
- RAM: 64MB, Nanya NT5TU32M16DG-AC
- Serial: 115200 baud, no header, 3.3V
J2: Vcc (arrow), Gnd, Tx, Rx
- USB: USB 2, 5V
- Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N
300 Mb/s, 2T2R
- WiFi1: 2.4 GHz 802.11 b/g/n integrated
300 Mb/s, 2T2R
- Antennas: 2 per radio, internal
- LEDs: 1 programmable power (amber)
2 programable radio (blue)
1 programable WPS-5G (blue)
1 non-programable WAN activity (blue)
1 unconfigured WPS-2.4G (amber)
- Buttons: GPIO: Reset, WPS
Installation:
Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.
The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.
As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt. The TFTP client is configured by default with
client: 192.168.99.9
server: 192.168.99.8
filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.
Known issues:
1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.
2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.
3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.
Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
