* Revert the switch_lan_bmp and switch_wan_bmp to match the values from
the original device support DTS
* Add specific malibu_first_phy_addr, as it differs from default for
this device
Fixes: #14234
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Samir Ibradžić <sibradzic@gmail.com> # Buffalo WXR-6000AX12P
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Unielec u7621-01.
According to the bootlog, MT7612E (5 GHz) is connected to pcie2, and
MT7603E (2 GHz) is connected to pcie1:
[ 1.294844] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 1.308635] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.318277] mt7621-pci 1e140000.pcie: PCIE2 enabled
Also correct the led activity for the MT7603e - not used on the MT7612e
Signed-off-by: David Bentham <db260179@gmail.com>
This node is useless because MT7621 uses the generic mips systick
driver instead of the ralink systick driver.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add support for wireless offload package in default configuration for
-Cudy WR3000
-Confiabits MT7981
For some reason those ware missing. I confirm this work for my Cudy WR3000
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Kernel 5.15 introduced a significant change to spi-nor subsystem [1],
which would the SPI-NOR core to no longer unprotect the Flash chips if
their protection bits are non-volatile, which is the case for MX25L6405D
and MX25L12805D, used in Ubiquiti XW and WA lines of devices [2].
However, their bootloader forcibly enables this protection before
continuing to boot, making the kernel not unprotect the flash upon boot,
causing JFFS2 to be unable write to the filesystem. Because sysupgrade
seems to unlock the flash explicitly, the upgrade will work, but the
system will be unable to save configrationm showing the following symptom
in the kernel log:
[ 86.168016] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 86.192344] jffs2_build_filesystem(): unlocking the mtd device...
[ 86.192443] done.
[ 86.200669] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 86.220646] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001e0000
[ 86.292388] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001d0000
[ 86.324867] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001c0000
[ 86.355316] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001b0000
[ 86.402855] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001a0000
Disable the write protection unconditionally for ath79/generic subtarget,
so the XW and WA devices can function again. However, this is only a
stopgap solution - it probably should be investigated if there is a way
to selectively unlock the area used by rootfs_data - but given the lock
granularity, this seems unlikely.
With this patch in place, rootfs_data partition on my Nanostation Loco
M5 XW is writable again.
Fixes: #12882Fixes: #13750
Fixes: 579703f38c ("ath79: switch to 5.15 as default kernel")
Link: http://www.infradead.org/pipermail/linux-mtd/2020-October/082805.html
Link: https://forum.openwrt.org/t/powerbeam-m5-xw-configuration-loss-after-reboot/141925
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
The MAC embedded in rtl93xx switch SoCs needs different mac mode bits set
to support 10BaseT and 100BaseT link modes. Set them accordingly.
This change has been tested on a ZyXEL XGS1250-12.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This reverts commit 3004c20614.
The commit added the needed packages for the new target
to the generic x86_64 image. This results into unwanted
modules and firmware files for other x86 devices.
Additionally, there is the following error message
while booting the image on other x86 devices:
[ 8.531720] kmodloader: 1 module could not be probed
[ 8.532613] kmodloader: - leds-mlxcpld - 0
For now, the needed packages will have to be selected
manually while configuring the image.
Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
Works around a build issue when building on a host with an older glibc,
where it would fail to detect ELF support in libbfd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The Puzzle devices come with an I2C-connected Epson RX8130 RTC.
Disable the (dysfunctional) RTC units of the SoC and add driver
kmod-rtc-ds1307 to support the Epson RX8130 instead.
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
730b4656e6b1 netifd: fix undefined va_list value which can cause crashes
c59457f69709 device: Log error message if device initialization failed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Prior to this commit, "localuse" (which enables local resolving through
dnsmsasq) was off by "default". That default was in turn overridden when
"noresolv" was unset (which itself is the default for "noresolv") *and*
"resolvfile" was "/tmp/resolv.conf.d/resolv.conf.auto" (also the default
for this parameter).
In other words, the "default" unset value for "localuse" would only be
ever used in specific *non-default* configurations.
However, the problem with that logic is that a user who wants to ignore
their ISP-provided resolvers by setting "noresolv" to true ends up with
a device that will *only use* said resolvers for local DNS queries,
serving clients' queries via dnsmasq (which now ignores the ISP
resolvers). This can lead to confusion and break random setups as the
DNS lookup performed on clients behalf can differ in their replies from
DNS lookups performed locally on the router.
Furthermore, "localuse" is not configurable through Luci, contrary to
the other two involved settings, adding further confusion for the end
user.
To work around this situation, the logic that sets "localuse" is
inverted: "localuse" now defaults to on by default, and IFF "noresolv"
is unset (default) AND "resolvfile" is changed from default THEN
"localuse" gets turned back off, allowing for more sensible behaviour.
"localuse" value set in config/dhcp still overrides the logic in all
cases, as it did already.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Commit 25746a3fa2da ("drm/i915: fix up merge with usb-next branch") was
internally applied to the 5.15 patch but wasn0t applied to the backport
for kernel 6.1. Apply the same treatement also there to fix compilation
warning.
Fixes: a14240d384 ("kernel: backport list_count_nodes()")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
XHCI bus numbers are assigned dynamically, it may varies among boards,
match the device irq name with regexp, drop the hardcoded name.
Signed-off-by: Furong Xu <xfr@outlook.com>
From the original Patch:
|In 749237967a downstream dts was replaced with upstream accepted
|patch. But in upstream version last partition was called "rootfs"
|instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
|This patch restore proper label.
|
|Fixes: 749237967a ("kirkwood: Replace dtses with upstream accepted")
|
|Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(patch updated to include 6.1, dropped label properties)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 512MB of DDR3
Flash1: Eon EN25S64 8MB
Flash2: MX30UF2G18AC 256MB
Ethernet: 2x 2.5G RJ45 port
Phone: 1x RJ11 port (SPI)
USB: 1x Type-C 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Button: Reset, WPS
Flash instructions:
1. Connect the router via serial port (115200 8N1 1.8V)
2. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
3. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
4. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This patch cleans up and standardizes realtek-poe support for realtek
based switches that have supported PoE ports.
The power output of switches supported by realtek-poe package can be
configured in the 02_network ucidef_set_poe() function. This was missed
when some PoE capable switches supported by realtek-poe were added.
The realtek-poe package at one point replaced a lua-rs232 based script
and some devices were not updated to use the realtek-poe package.
Consistently add realtek-poe package to DEVICE_PACKAGES for switches
with supported PoE.
Signed-off-by: Raylynn Knight <rayknight@me.com>
We have a report in the forum, that lan/wan is non-functional
on the EAP102 (https://forum.openwrt.org/t/edgecore-eap102/178449)
Fixing that by swapping label and phy-handle of the dp-nodes and
updating the lan/wan bmp.
Note: the original commiter of the device support seems absent for a
long time in the forum and on the OpenWrt github group.
Tested-by: Antonio Della Selva <antonio.dellaselva@uniurb.it>
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
SoC: Qualcomm IPQ8072A
Flash: Toshiba NAND 1GiB
RAM: 1 GiB of DDR3 466 MHz
Ethernet: 4x 1Gbps + 1x 2.5Gbps
WiFi1: QCN5024 2.4GHz ax 4x4
WiFi2: QCN5054 5GHz ax 4x4
Button: WiFi, WPS, Reset
Modem: RG500Q-EA
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.bin, and host it with tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.bin
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Replace blanks with tabs, also sort base-files alphabetically.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Correct oob size from 128 to 256 for Toshiba TH58NYG3S0HBAI4 flash.
Since it is not ONFI compliant NAND, the model name cannot be read
from anywhere, add a static NAND ID entry to correct this.
However, the NAND ID of this flash is inconsistent with the datasheet.
The actual NAND ID is only 4 ID bytes, the last ID byte is missing.[1]
Maybe this flash is counterfeit, or maybe it's another problem.
Another Toshiba flash had the same problem before. Refer to commit
a83dc6b ("kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx"), put
the patch into qualcommax target to avoid affecting other devices.
The patch is verified on Arcadyan AW1000.
[1] Datasheet available at (the ID table is on page 50):
https://europe.kioxia.com/content/dam/kioxia/newidr/productinfo/datasheet/201910/DST_TH58NYG3S0HBAI4-TDE_EN_31565.pdf
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Detach of-mdio dependency from stmmac-core kmod to fix support for
x86_64 target. This target doesn't use OpenFirmware infrastructure and
stmmac-core for the dwmac-intel driver doesn't depends on it.
Add kmod-of-mdio to any other user of stmmac-core as it's not inherit
from stmmac-core anymore.
Fixes: #14209
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move pcs-xpcs kmod from armsr modules.mk to generic modules package.
Also add additional dependency to x86_64 as stmmac-core it's now used
by x86_64 target and depends on this package.
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Explain some of the more obscure logic, or where we deviate from
what the original awk code did. Also, give a count of the usable
addresses on the subnet.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This is useful if you later need to perform numeric range-checking
on addresses, i.e. to see if an address falls inside a CIDR range,
etc. and what interface it corresponds to.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
