Newer RPi 4 Rev 6 (8 GB models and recent 2 GB / 4 GB models) ship with
the so-called C0 processor which can run turbo mode at 1.8 GHz max rather
than 1.5 GHz gracefully. Add 'arm_boost=1' to pi4 section of to enable.
Note that this setting has no effect on older chips; they continue with
their 1.5 GHz max unless users overclock them.
Ref: https://www.raspberrypi.com/news/bullseye-bonus-1-8ghz-raspberry-pi-4
Signed-off-by: John Audia <graysky@archlinux.us>
This makes the WAN interface and port appear in
LuCi -> Network -> Switch on Linksys MR8300.
This allows to configure a VLAN on WAN.
Fixes: FS#4227
Signed-off-by: Julien Cassette <julien.cassette@gmail.com>
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.
Hardware specification:
- CPU: IPQ4019
- RAM: 256MB
- Flash: NAND 128MB + NOR 2MB
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
- LTE: mPCIe cat 12 card (Modem chipset MDM9250)
- LAN: 4 Gigabit Ports
- USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
- Serial console: X8 connector 115200 8n1
Known issues:
- Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
are driven by cpu.
- Wifi LED is triggered by phy0tpt only
- No VoIP support
- LAN1/WAN port is configured as WAN
- ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
and WLAN0/1
Opening the case:
1. Take of battery lid (no battery support for this model, battery cage
is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.
Console connection (X8 connector):
1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
- VCC (3.3V)
- TX
- RX
- GND
Install Instructions:
Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
setenv serverip 192.168.1.3
setenv ipaddr 192.168.1.72
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
to stock.
6. Login via ssh or serial and remove stock partitions:
ubiattach -m 9
ubirmvol /dev/ubi0 -N ubi_rootfs
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
brings back the ath10k QCA9980 wifi nodes to which
it adds ASROCK's wifi calibration data. These are
now provided by the ath10k_firmware.git's board-2.bin.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kalle Valo ath10k-firmware repository no longer provides the
legacy board.bin files for the qca99x0 chips. Instead he
copied over the codeaurora version and add more board files.
In the future, this board-2.bin should find its way to
linux-firmware.git, which would allow us to remove the
extra download code completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
converts extraction entries from 11-ath10k-caldata into
nvmem-cells in the individual board's device-tree file.
The patch also moves previously existing referenced
nvmem-cells data nodes which were placed at the end
back into the partitions node. As well as removing
some duplicated properties from qcom-ipq8065-xr500.dts's
art (the included nighthawk.dtsi defines those already).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the WNDR4700 can fetch its calibration data and
mac-addresses directly from the "wifi_data" partition.
This allows us to get rid of the 10-ath9k-eeprom file
for the apm821xx target completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
in order to get nvmem-cells to work on AP and routers
(Netgears WNDR4700). The nvmem-cell needs to be within
a fixed-partition dt-node.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
this should have been removed together with linux 5.4 APM821XX
support. Currently, this didn't hurt or broke something. But it
will in the next stable kernel release.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The SDK does not ship the generic platform files. Use relative path for
GENERIC_PLATFORM_DIR to make it work. This points it at the files from
the feed directory instead of the base SDK path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changelog:
backend_startup_project
Add a man page backend to refman
extract_objects() supports generated sources
Python 3.6 support will be dropped in the next release
Warning if check kwarg of run_command is missing
meson rewrite can modify extra_files
meson rewrite target <target> info outputs target's extra_files
Visual Studio 2022 backend
Support for CMake <3.14 is now deprecated for CMake subprojects
Added support for sccache
install_symlink function
Signed-off-by: Rosen Penev <rosenp@gmail.com>
All devices which used this package migrated to the kernel GPIO-line
watchdog driver and configure it over their DT.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The commit 04e91631e0 ("om-watchdog: add support for Teltonika RUT5xx
(ramips)") used the deprecated om-watchdog daemon to handle the GPIO-line
connected watchdog on the Teltonika RUT5xx.
But this daemon has massive problems since commit 30f61a34b4
("base-files: always use staged sysupgrade"). The process will always be
stopped on sysupgrades. If the sysupgrade takes slightly longer, the
watchdog is not triggered at the correct time and thus the sysupgrade will
interrupted hard by the watchdog sysupgrade. And this hard interrupt can
easily brick the device when there is no fallback (dual-boot, ...).
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This solves issue with DDR training on Turris Omnia.
Log:
******** DRAM initialization Failed (res 0x1) ********
DDR3 Training Sequence - FAILED
ERROR ### Please RESET the board ###
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Now that we can have both legacy and nft iptables variants
installed at the same time, install the legacy symlinks
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
As nftables is now the default, ip(6)tables-nft gets higher priority
The removed symlinks ("$(CP)" line) will now be installed by the
ALTERNATIVES mechanism
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
according to iptables-nft man page,
"These tools use the libxtables framework extensions and hook to the nf_tables
kernel subsystem using the nft_compat module."
This means that to work, iptables-nft needs the same modules as
iptables legacy except the ip(6)table-{filter,mangle,nat,raw}
ip_tables, ip6tables.
When those modules are loaded iptables-nft-save output contains
"# Warning: iptables-legacy tables present, use iptables-legacy-save to see them"
But as long as it's empty it should not be a problem.
To have nft properly display the rules created by ip(6)tables-nft we need
all iptables targets and matches to be built as extension and not built-in
(/usr/lib/iptables/libip(6)t_*.so)
When switching a package to iptables-nft, you need to keep the
iptables-mod-* dependencies
This patch does minimal changes:
- remove the direct iptables-nft -> iptables dependency
- and more important add nft-compat dependency
The rule
iptables-nft -A OUTPUT -d 8.8.8.8 -m comment --comment "aaa" -j REJECT
becomes
table ip filter {
chain OUTPUT {
type filter hook output priority filter; policy accept;
ip daddr 8.8.8.8 # xt_comment counter packets 0 bytes 0 # xt_REJECT
}
}
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Remove the 434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch, it was
already applied to Linux 5.10.37 and is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add option to compile kmod-vrf, support for Virtual Routing and
Forwarding (Lite).
This module depends on NET_L3_MASTER_DEV, which is a boolean kernel
option, so we need to create a configuration option also for this, and
make kmod-vrf depend on it.
Signed-off-by: Marek Behún <kabel@kernel.org>
The sizes of the ipk changed on MIPS 24Kc like this:
13281 uboot-envtools_2021.01-54_mips_24kc.ipk
13308 uboot-envtools_2022.01-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sizes of the ipk changed on MIPS 24Kc like this:
11248 libcap_2.51-1_mips_24kc.ipk
14461 libcap_2.63-1_mips_24kc.ipk
18864 libcap-bin_2.51-1_mips_24kc.ipk
20576 libcap-bin_2.63-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This release fixes two security mount(8) and umount(8) issues:
CVE-2021-3996
Improper UID check in libmount allows an unprivileged user to unmount FUSE
filesystems of users with similar UID.
CVE-2021-3995
This issue is related to parsing the /proc/self/mountinfo file allows an
unprivileged user to unmount other user's filesystems that are either
world-writable themselves or mounted in a world-writable directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The man page of the raw tool does not build because the disk-utils/raw.8
file is missing. It looks like it should be in the tar.xz file we
download, but it is missing.
We do not package the raw tool, so this is not a problem.
This fixes the following build error:
No rule to make target 'disk-utils/raw.8', needed by 'all-am'. Stop.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sizes of the ipk changed on MIPS 24Kc like this:
289764 strace_5.14-1_mips_24kc.ipk
310899 strace_5.16-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
795f420 cmis: Rename CMIS parsing functions
369b43a cmis: Initialize CMIS memory map
da16288 cmis: Use memory map during parsing
6acaeb9 cmis: Consolidate code between IOCTL and netlink paths
d7d15f7 sff-8636: Rename SFF-8636 parsing functions
4230597 sff-8636: Initialize SFF-8636 memory map
b74c040 sff-8636: Use memory map during parsing
799572f sff-8636: Consolidate code between IOCTL and netlink paths
9fdf45c sff-8079: Split SFF-8079 parsing function
2ccda25 netlink: eeprom: Export a function to request an EEPROM page
86792db cmis: Request specific pages for parsing in netlink path
6e2b32a sff-8636: Request specific pages for parsing in netlink path
c2170d4 sff-8079: Request specific pages for parsing in netlink path
9538f38 netlink: eeprom: Defer page requests to individual parsers
664586e Merge branch 'review/next/module-mem-map' into master
50fdaec ethtool: Set mask correctly for dumping advertised FEC modes
c5e7133 cable-test: Fix premature process termination
73091cd sff-8636: Use an SFF-8636 specific define for maximum number of channels
837c166 sff-common: Move OFFSET_TO_U16_PTR() to common header file
8658852 cmis: Initialize Page 02h in memory map
27b42a9 cmis: Initialize Banked Page 11h in memory map
340d88e cmis: Parse and print diagnostic information
eae6a99 cmis: Print Module State and Fault Cause
82012f2 cmis: Print Module-Level Controls
d7b1007 sff-8636: Print Power set and Power override bits
429f2fc Merge branch 'review/cmis-diag' into master
32457a9 monitor: do not show duplicate options in help text
c01963e Release version 5.16.
The sizes of the ipk changed on MIPS 24Kc like this:
34317 ethtool_5.15-1_mips_24kc.ipk
34311 ethtool_5.16-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following security problems:
* Zeroize several intermediate variables used to calculate the expected
value when verifying a MAC or AEAD tag. This hardens the library in
case the value leaks through a memory disclosure vulnerability. For
example, a memory disclosure vulnerability could have allowed a
man-in-the-middle to inject fake ciphertext into a DTLS connection.
* Fix a double-free that happened after mbedtls_ssl_set_session() or
mbedtls_ssl_get_session() failed with MBEDTLS_ERR_SSL_ALLOC_FAILED
(out of memory). After that, calling mbedtls_ssl_session_free()
and mbedtls_ssl_free() would cause an internal session buffer to
be free()'d twice. CVE-2021-44732
The sizes of the ipk changed on MIPS 24Kc like this:
182454 libmbedtls12_2.16.11-2_mips_24kc.ipk
182742 libmbedtls12_2.16.12-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a minor corrective release over GDB 11.1, fixing the following issues:
* PR sim/28302 (gdb fails to build with glibc 2.34)
* PR build/28318 (std::thread support configure check does not use CXX_DIALECT)
* PR gdb/28405 (arm-none-eabi: internal-error: ptid_t remote_target::select_thread_for_ambiguous_stop_reply(const target_waitstatus*): Assertion `first_resumed_thread != nullptr' failed)
* PR tui/28483 ([gdb/tui] breakpoint creation not displayed)
* PR build/28555 (uclibc compile failure since commit 4655f8509fd44e6efabefa373650d9982ff37fd6)
* PR rust/28637 (Rust characters will be encoded using DW_ATE_UTF)
* PR gdb/28758 (GDB 11 doesn't work correctly on binaries with a SHT_RELR (.relr.dyn) section)
* PR gdb/28785 (Support SHT_RELR (.relr.dyn) section)
The sizes of the ipk changed on mips 24Kc like this:
2285775 gdb_11.1-3_mips_24kc.ipk
2287441 gdb_11.2-4_mips_24kc.ipk
191828 gdbserver_11.1-3_mips_24kc.ipk
191811 gdbserver_11.2-4_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
