Legacy minstrel is essentially unmaintained and was showing poor performance
Replace it with minstrel_ht and improve rate selection and sampling behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove deferred sampling code which does not work well with rate tables +
probing.
Fix tx status handling if the first invalid rate idx is not set to -1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
rt2800 olny gives you survey for current channel.
Survey-based ACS algorithms are failing to perform their job when working
with rt2800.
Make rt2800 save survey for every channel visited and be able to give away
that information.
There is a bug registred https://dev.archive.openwrt.org/ticket/19081 and
this patch solves the issue.
Signed-off-by: Markov Mikhail <markov.mikhail@itmh.ru>
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The vendor driver does things differently based on what it finds in the
SoC's CHIP_VER register, which should tell whether this is MT7620N or
MT7620A (PKG) and probably also the revision (VER) and most likely
also something about the silicon implementer (ECO).
Introduce codepaths just like the ones in the vendor driver to handle
the different chips properly.
Some of those paths are most likely dead code and left-overs from FPGA
versions or early prototypes of the chip. It'd thus be great if people
can post their kernel logs, at least the line telling the chip version
and eco, so we know what's actually out there in the wild -- all I
could find is
[ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
and
[ 0.000000] SoC Type: Ralink MT7620N ver:2 eco:6
which would make things easier, as then we really just need to know
whether it's MT7620N or MT7620A and not care about FPGA or prototypes
with ver <= 1 and eco <= 2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the nulldata frame was acked, the probe send count needs to be reset,
otherwise it will keep increasing until the connection is considered dead,
even though it fine.
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Minor cleanup and code reorganization, along with a change to not disable
offload anymore when a tkip or sw crypto key is added
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mac80211 reports a packet loss event to user space when 50 consecutive packets
were not acked. On a high throughput link with long aggregates and sudden
link changes, this can trigger way too easily.
Mitigate false positives by only triggering the event on a packet loss if
no ACK was received for at least a second
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Exchange the patch fixing the kernel ringbuffer WARNING flood for the
one accepted upstream.
Fixes commit a956c14d6a ("mac80211: util: don't warn on missing sband
iftype data")
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel currently floods the ringbuffer with warnings when adding a
mesh interface for a device not support HE 6GHz modes.
Return without warning in this case, as mesh_add_he_6ghz_cap_ie calls
ieee80211_ie_build_he_6ghz_cap regardless of the supported interface
modes.
Signed-off-by: David Bauer <mail@david-bauer.net>
The following patches:
* 972-ath10k_fix-crash-due-to-wrong-handling-of-peer_bw_rxnss_override-parameter.patch
* 973-ath10k_fix-band_center_freq-handling-for-VHT160-in-recent-firmwares.patch
are replaced by this commit in the upstream kernel:
* 3db24065c2c8 ("ath10k: enable VHT160 and VHT80+80 modes")
The following patches were applied upstream:
* 001-rt2800-enable-MFP-support-unconditionally.patch
* 090-wireless-Use-linux-stddef.h-instead-of-stddef.h.patch
The rtw88 driver is now split into multiple kernel modules, just put it
all into one OpenWrt kernel package.
rtl8812au-ct was patched to compile against the mac80211 from kernel
5.8, but not runtime tested.
Add a patch which fixes ath10k on IPQ40XX, this patch was send upstream
and fixes a crash when loading ath10k on this SoC.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq40xx/ map-ac2200]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make sure RF5592 is set for RT5592 chip which apparently sometimes
doesn't have RF defined (but always comes with RF5592).
This patch was originally submitted on linux-wireless by
Tom Psyborg <pozega.tomislav@gmail.com> but got rejected.
Turns out the patch is actually needed.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ath9k will already fallback on software-crypto for chipsets not
supporting IEEE802.11w (MFP). So advertising MFP is not dependent
on disabling HW crypto for all traffic entirely.
Tested on Sonicwall SonicPoint Ni (AR9132)
Signed-off-by: David Bauer <mail@david-bauer.net>
From: Rui Salvaterra <rsalvaterra@gmail.com>
Date: Mon, 25 May 2020 14:49:07 +0100
Subject: [PATCH] rt2800: enable MFP support unconditionally
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes the following compile error seen on the mpc85xx target:
CC [M] /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o
In file included from /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/stddef.h:17,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/uapi/linux/wireless.h:77,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/linux/wireless.h:13,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:89:
/builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/alltypes.h:106:15: error: conflicting types for 'ptrdiff_t'
typedef _Addr ptrdiff_t;
^~~~~~~~~
In file included from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/types.h:4,
from ./include/linux/list.h:5,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/list.h:3,
from ./include/linux/module.h:9,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/module.h:3,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:79:
./include/linux/types.h:65:28: note: previous declaration of 'ptrdiff_t' was here
typedef __kernel_ptrdiff_t ptrdiff_t;
^~~~~~~~~
scripts/Makefile.build:265: recipe for target '/linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o' failed
Fixes: 289c632425 ("mac80211: Update to version 5.7-rc3-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
The 131-Revert-mac80211-aes-cmac-switch-to-shash-CMAC-driver.patch patch
was manually adapted to the changes in kernel 5.7.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport to the latest minor version.
The removed patch was a backport from the upstream kernel which is now
integrated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: 9e5ab25027
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
If we know that we have an encrypted link (based on having had
a key configured for TX in the past) then drop all data frames
in the key selection handler if there's no key anymore.
This fixes an issue with mac80211 internal TXQs - there we can
buffer frames for an encrypted link, but then if the key is no
longer there when they're dequeued, the frames are sent without
encryption. This happens if a station is disconnected while the
frames are still on the TXQ.
Detecting that a link should be encrypted based on a first key
having been configured for TX is fine as there are no use cases
for a connection going from with encryption to no encryption.
With extended key IDs, however, there is a case of having a key
configured for only decryption, so we can't just trigger this
behaviour on a key being configured.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The calibration patches for MT7620 unnecessarily export symbols and
populate never accessed function pointers. Remove all that and make
functions static as the only place where each of those functions is
called is within rt2800lib.c.
Also make code more readable by fixing indentation, removing
unnecessary parantheses and simplifying some instructions using
shorthands here and there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Do not export static functions, they are anyway not referenced by any
code in a different module.
This fixes the following compile warning:
WARNING: "rt2800_rf_aux_tx0_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_write_dc" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_configstore" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_do_sqrt_accumulation" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_configrecover" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_loft_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_iq_search" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_setbbptonegenerator" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
WARNING: "rt2800_rf_aux_tx1_loopback" [/drivers/net/wireless/ralink/rt2x00/rt2800lib] is a static EXPORT_SYMBOL_GPL
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On platforms that do not have CONFIG_MTD enabled, loading the
rt2x00lib kernel module fails because it depends on symbols from
the mtd module ("Unknown symbol get_mtd_device_nm").
This commit disables the code that can read the eeprom from mtd if
mtd is not enabled.
Signed-off-by: Sven Over <sp@cedenti.st>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ath10k-ct supports the combination to select IBSS (ADHOC) mode and
different beacon intervals together. mac80211 does not like this
combination, but Ben says this is ok, so remove this check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds 'qca,gpio-mask=<u32>' device tree property to ath9k node.
This optional setting is a hack and should only be used in very special
(and rare) cases when a button or LED is wired to a GPIO pin normally
masked out (due to being one-way etc). Netgear WNDR4300 v2 is one such
example - it uses GPI9 for RFKILL.
See ath9k/reg.h *_GPIO_MASK constants.
Use with caution and expect to see stream of kernel warnings if wrong
mask value is provided.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
These two hacks are no longer necessary as they've
been moved to a special variant of kmod-ath10k-ct.
So, if you have a device suffering from low-memory
situation and getting applications crashes due to
the OOM reaper or kernel panics with ath10k, please
use the "kmod-ath10k-ct-smallbuffers" package from
now on.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds a (currently missing) throughput LED trigger for the rt2x00
driver. Previously, LED triggers had to be assigned to the netdev, which
was limited to a single VAP.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Christoph Krapp <achterin@googlemail.com>
This update doesn't include:
3b1e0a7bdfee brcmfmac: add support for SAE authentication offload
be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This updates mac80211 to backports based on kernel 5.4-rc8.
The deleted patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This potentially fixes some issues seen on IBSS
when interfaces go out of range and then re-appear.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The skb_get_hash_perturb() function now takes a siphash_key_t instead of
an u32. This was changed in commit 55667441c84f ("net/flow_dissector:
switch to siphash"). Use the correct type in the fq header file
depending on the kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The QCA953x only supports 25 MHz refclk, however some OEMs set an
invalid bootstrap value for the REF_CLK option, which would break the
clock detection in ath9k.
Force the QCA953x refclk to 25MHz in ath9k, as this is (according to the
datasheet) the only valid frequency.
Signed-off-by: David Bauer <mail@david-bauer.net>
https://patchwork.kernel.org/patch/11224189/
--
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c984 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
--
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This updates mac80211 to backports based on kernel 5.4-rc2
ath10k-ct was updated to match the API changes and iw now uses the new
nl80211.h header file.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
This backport fixes high latency (>100ms) on the WiFi link when using a
QCA988x Wave 1 radio. The ath10k-ct driver is not affected by this bug
from my testing, hence why it hasn't been discovered earlier.
Signed-off-by: David Bauer <mail@david-bauer.net>
https://patchwork.kernel.org/patch/11161981/
--
From: Stanislaw Gruszka <sgruszka@redhat.com>
Subject: [PATCH] rt2x00: initialize last_reset
Initialize last_reset variable to INITIAL_JIFFIES, otherwise it is not
possible to test H/W reset for first 5 minutes of system run.
Fixes: e403fa31ed71 ("rt2x00: add restart hw")
Reported-and-tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
--
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This makes brcmfmac use the same wiphy after PCIe reset to help user
space handle corner cases (e.g. firmware crash).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
From: Stanislaw Gruszka <sgruszka@redhat.com>
This reverts commit 9ad3b55654455258a9463384edb40077439d879f.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b5565445 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Close cooperation with Lorenzo Bianconi resulted
in these patches which fix all remaining seen issues
when using dynack.
Fix link losses when:
- Late Ack's are not seen or not present
- switching from too low static coverage class to dynack on a live link
These are fixed by setting the Ack Timeout/Slottime to
the max possible value for the currently used channel width when
a new station has been discovered.
When traffic flows, dynack is able to adjust to optimal values
within a few packets received (typically < 1 second)
These changes have been thoroughly tested on ~60 offshore devices
all interconnected using mesh over IBSS and dynack enabled on all.
Distances between devices varied from <100m up to ~35km
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
To do not brake HW restart we should keep initialization vectors data.
I assumed that on start the data is already initialized to zeros, but
that not true on some scenarios and we should clear it. So add
additional flag to check if we are under HW restart and clear IV's
data if we are not.
Patch fixes AP mode regression.
Patch pending on linux-wireless and imported from patchwork.
Fixes: 0b2c42ced2 ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes a bug introduced in backports from kernel 5.1 which makes
ath10k crash on QCA9984 when a station connects. The FW sends a airtime
report, but this station is not yet fully registered and a NULL pointer
is used.
Fixes: 0b2c42ced2 ("mac80211: Update to version 5.2-rc7")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
The type of the RT2X00_LIB_EEPROM config option was changed to bool,
because boolean is an invalid value and the new kconfig system
complained about this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This doesn't include 9ff8614a3dbe ("brcmfmac: use separate Kconfig file
for brcmfmac") due to a few conflicts with backports changes.
An important change is:
[PATCH 2/7] brcmfmac: change the order of things in brcmf_detach()
which fixes a rmmod crash in the brcmf_txfinalize().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This updates mac80211 to version 5.2-rc7, this contains all the changes
to the wireless subsystem up to Linux 5.2-rc7.
* The removed patches are applied upstream
* b43 now uses kmod-lib-cordic
* Update the nl80211.h file in iw to match backports version.
* Remove the two backports from kernel 4.9, they were needed for mt76,
but that can use the version from backports now, otherwise they
collide and cause compile errors.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
struct ieee80211_local needs to be passed in separately instead of
dereferencing the (potentially NULL) sdata
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace the patch introduced by commit d0b969eee8 ("mac80211: rt2x00:
do not increment sequence number while re-transmitting") was merged
into wireless-drivers.git. Replace our version with the merged version.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The removed patches are now integrated in the upstream kernel.
Refresh all patches on top of the new backports release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Imported from patchwork, patches marked with '=' have already been in
our tree:
[v3,1/4] cfg80211: add ratelimited variants of err and warn
[v3,2/4] rt2x00: use ratelimited variants dev_warn/dev_err
[v3,3/4] rt2x00: check number of EPROTO errors
=[v3,4/4] rt2x00: do not print error when queue is full
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently STA+AP re-transmitting the management frames with
incremented sequence number if hardware is assigning the sequence.
Fix is to assign the sequence number for Beacon by hardware
and for other Management frames software will assign the
sequence number
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
consolidate patch 651-rt2x00-remove-unneccesary-code.patch.
fixup the most obvious whitespace problems in RXIQ and TX-LOFT code.
always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid
compiler warning about them being potentially uninitialized.
no functional changes (intended)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes: db90c243a0 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/10692383/
Fixes: d9eefa7a70 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix crash due to passing invalid r2x00dev->eeprom_file pointer to
release_firmware(). Since we copy eeprom data with EEPROM_SIZE
in rt2800_read_eeprom() we can use eeprom_file->size as marker
if the file was crated by request_firmware().
Acked-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cherry-pick Multi-AP commits from uptream:
9c06f0f6a hostapd: Add Multi-AP protocol support
5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support
a1debd338 tests: Refactor test_multi_ap
bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS
cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation
56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext()
83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS
66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS
8682f384c hostapd: Add README-MULTI-AP
b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Those have by now been merged into wireless-drivers-next:
17ae2acd1a6f rt2x00: remove unneeded check
5991a2ecd070 rt2x00: remove confusing AGC register
9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
backport from wireless-drivers-next, replacing some existing patches in
our tree (marked with '=' are those which were already present):
f483039cf51a rt2x00: use simple_read_from_buffer()
=5c656c71b1bf rt2800: move usb specific txdone/txstatus routines to rt2800lib
=0b0d556e0ebb rt2800mmio: use txdone/txstatus routines from lib
=5022efb50f62 rt2x00: do not check for txstatus timeout every time on tasklet
=adf26a356f13 rt2x00: use different txstatus timeouts when flushing
=0240564430c0 rt2800: flush and txstatus rework for rt2800mmio
6eba8fd22352 rt2x00: rt2400pci: mark expected switch fall-through
10bb92217747 rt2x00: rt2500pci: mark expected switch fall-through
916e6bbcfcff rt2x00: rt2800lib: mark expected switch fall-throughs
641dd8068ecb rt2x00: rt61pci: mark expected switch fall-through
750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
=c2e28ef7711f rt2x00: reduce tx power to nominal level on RT6352
a4296994eb80 rt2x00: Work around a firmware bug with shared keys
2587791d5758 rt2x00: no need to check return value of debugfs_create functions
pending on linux-wireless:
rt2x00: remove unneeded check
rt2x00: remove confusing AGC register
rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
rt2800: comment and simplify AGC init for RT6352
rt2x00: do not print error when queue is full
rt2800: partially restore old mmio txstatus behaviour
rt2800: new flush implementation for SoC devices
rt2800: move txstatus pending routine
rt2800mmio: fetch tx status changes
rt2800mmio: use timer and work for handling tx statuses timeouts
rt2x00: remove last_nostatus_check
rt2x00: remove not used entry field
rt2x00mmio: remove legacy comment
While at it also rename some existing patches now that there are
separate folders with patches for each driver to make things a bit
nicer to handle.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This updates mac80211 to backports version 4.19.23-1 which includes all
the stable fixes from kernel 4.19.23.
The removed patches are included in this version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag. Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.
By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Remove 980-rt2x00-reduce-power-consumption-on-mt7620.patch which in
combination with the most recently added patch reportedly causes TX
power to be too weak.
"without patches rssi on receiver is ~ -23dBm with 980 about -35dBm,
with both patches drops below -40dBm. with 987 only ~-28dBm"
We may need to reconsider this once we have implemented TSSI.
Fixes: cdb58b2bfe ("mac80211: rt2x00: reduce tx power to nominal level on RT6352")
Reported-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds several country codes to the regd.h and regd_common.h
files in order to support devices whose country codes are not present in
the original list.
Without this patch, all devices whose manufacturer programmed any of these
code in their EEPROM will run without wireless interfaces.
Signed-off-by: Oever González <notengobattery@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [matched signed-off]
Initially this patch was introduced as a quick fix following
the removal of 936-ath10k_skip_otp_check.patch which caused
multiple ath10k pcie devices in various ipq806x and ar71xx/ath79
targets to malfunction.
Thankfully, the affected devices have been updated to utilize
the pre-caldata method. And finally with the switch to ath10k-ct,
which never had the patch or any reports of similar issues, I
think it's time to remove this patch since it is no longer needed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This fixes:
1) Getting STA info with newer firmwares
2) Getting DMI / UEFI / OF data
3) Possible memory corruption in firmware loading code
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Using fwctx variable after brcmf_fw_request_done() was executed meant
accessing freed memory.
2) Using fwctx->completion for the wait_for_completion_timeout() call
could reuslt in NULL pointer dereference on fw loading error or if
brcmf_fw_request_done() was executed quickly enough.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Based on the process of discovery in
https://github.com/openwrt/openwrt/pull/1613, it has become clear
that (at least) the PowerCloud System CR5000 was unable to get
working 5GHz wireless (PCIe) because AH_USE_EEPROM was unconditionally
masked out, not only when qca,noeeprom was in the DTS.
This patch moves mask AH_USE_EEPROM into the if ... qca,noeeprom
OF test.
Thanks to Christian Lampartar (@chunkeey) for the heavy lifting and help.
Patch has been prepared for upstream and will be submitted after review
by @chunkeey and @xdarklight.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
This updates the backports package used in mac80211 to version 4.19.7-1
which is based on kernel 4.19.7. This integrates all the stable fixes
introduces in this kernel version.
The deleted patches are not needed any more because they are either
included in the upstream Linux kernel 4.19.7 or in backports 4.19.7-1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This partitialy reverts commit ccab68f2d3.
Registering the GPIO chip without a parent device completely breaks the
ath9k GPIOs for device tree targets.
As long as boards using the devicetree don't have the gpio-controller
property set for the ath9k node, the unloading of the driver works as
expected.
Register the GPIO chip with the ath9k device as parent only for OF
targets to find a trade-off between the needs of driver developers and
the broken LEDs and buttons seen by users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
An upstream change broke brcmfmac when loaded with modparam roamoff=1.
As we are carrying a patch that enables roamoff by default on the
brcm2708 target to improve stability, wireless is currently broken
there. Add a patch to fix brcmfmac with roamoff=1.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently, dynack was only tested upstream using AP/STA mode.
Testing it on IBSS, showed that late-ack detection was broken.
This is caused due to dynack using Association Request/Response
frames for late-ack detection, which IBSS does not use.
Also allowing Authentication frames here solves this.
A second issue also got fixed, which was also seen AP/STA mode:
When a station was added, the estimated value would be exponentially averaged
using 0 as a starting point.
This means that on larger distances, the ack timeout was still not high
enough before synchronizing would run out of late-ack's for estimation.
Fix this by using the initial estimated value as a baseline
and only start averaging in the following estimation rounds.
Test setup:
- 2x identical devices: RB912UAG-5HPnD + 19dB sector
- IBSS
- 2x2 802.11an (ar9340), HT20, long GI
- RSSI's -70 / -71
- Real distance: 23910 meter
Results (60s iperf runs):
Fixed coverage class 54 (up to 24300m):
* 21.5 Mbits/sec
Dynack:
* 28.9 Mbits/sec
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Software crypto wasn't working for management frames because the flag
indicating management frame crypto was missing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The __change_mtu() function is only compiled when
CPTCFG_IPW2200_PROMISCUOUS is set, more it to the general area.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an official release with some minor changes compared to the
unofficial 4.19-rc4-1 we used before.
* added bcma and ssb again, which is removed in OpenWrt
* fix to build with kernel 4.19
* other minor fixes not relevant for Openwrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These patches were added after the new matches structure for the
mac80211 package was created. All the deleted patches are already
integrated in kernel 4.19-rc4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates mac80211 to backports based on kernel 4.19-rc4.
I plan to integrate all the patches which are in this tar into upstream
backports soon.
I used the backports generated from this code:
https://github.com/hauke/backports/commits/wip2
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to Stanislaw Gruszka the patch
600-23-rt2x00-rt2800mmio-add-a-workaround-for-spurious-TX_F.patch
should be dropped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add RXIQ calibration found in mtk driver. With old openwrt builds this gets us ~8Mbps more of RX bandwidth (test with iPA/eLNA layout).
Please try if this makes any difference among various board/RF layouts.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Add RXDCOC calibration code from mtk driver. Please try if this makes any difference among various board/RF layouts.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Write registers required for reducing power consumption like the vendor
driver does when ADJUST_POWER_CONSUMPTION_SUPPORT is set.
This helps devices to sync at better TX/RX rates and improves overall
performance.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: edited commit message]
Registering a GPIO chip with the ath9k device as parent prevents unload,
because the gpiochip core increases the module use count.
Unfortunately, the only way to avoid this at the moment seems to be to
register the GPIO chip without a parent device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Monitor mode isn't supported yet with brcmfmac, it's just an early work.
This also prepares brcmfmac to work stable with new firmwares which use
updated struct for passing STA info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The most important is probably regression fix in handling platform
NVRAM. That bug stopped hardware from being properly calibrated breaking
e.g. 5 GHz for Netgear R8000.
Other than that it triggers memory dumps when experiencing firmware
problems which is important for debugging purposes.
Fixes: 7e8eb7f309 ("mac80211: backport brcmfmac firmware & clm_blob loading rework")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit refreshes and updates the VHT160 ath10k support fix patches
and adds a number of backports from ath-next:
* 8ed05ed06fca ath10k: handle tdls peer events
* 229329ff345f ath10k: wmi: modify svc bitmap parsing for wcn3990
* 14d65775687c ath10k: advertise TDLS wider bandwidth support for 5GHz
* bc64d05220f3 ath10k: debugfs support to get final TPC stats for 10.4 variants
* 8b2d93dd2261 ath10k: Fix kernel panic while using worker (ath10k_sta_rc_update_wk)
* 4b190675ad06 ath10k: fix kernel panic while reading tpc_stats
* be8cce96f14d ath10k: add support to configure channel dwell time
* f40105e67478 ath: add support to get the detected radar specifications
* 6f6eb1bcbeff ath10k: DFS Host Confirmation
* 260e629bbf44 ath10k: fix memory leak of tpc_stats
* 38441fb6fcbb ath10k: support use of channel 173
* 2e9bcd0d7324 ath10k: fix spectral scan for QCA9984 and QCA9888 chipsets
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[move backported patches in the 3xx number space, bring in upstream order,
replace incomplete patch files with git format-patch ones, rewrite commit
message, fix subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
After a very enlightening but unfortunately far too short exchange with Jes
we mutually agreed to drop the patches. They are unfortunately not ready
yet.
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: John Crispin <john@phrozen.org>
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.
Signed-off-by: Mathias Kresin <dev@kresin.me>
