- Remove obsolete patch chunks regarding fixed_freq
- Instead of patching in custom HT40+/- parameters, use the standard
config syntax as much as possible.
- Use fixed_freq for mesh
- Fix issues with disabling obss scan when using fixed_freq on mesh
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The beacon_int is currently set explicitly for hostapd and when LEDE uses
iw to join and IBSS/mesh. But it was not done when wpa_supplicant was used
to join an encrypted IBSS or mesh.
This configuration is required when an AP interface is configured together
with an mesh interface. The beacon_int= line must therefore be re-added to
the wpa_supplicant config. The value is retrieved from the the global
variable.
Fixes: 1a16cb9c67 ("mac80211, hostapd: always explicitly set beacon interval")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [rebase]
The wpa_supplicant code for IBSS allows to set the mcast rate. It is
recommended to increase this value from 1 or 6 Mbit/s to something higher
when using a mesh protocol on top which uses the multicast packet loss as
indicator for the link quality.
This setting was unfortunately not applied for mesh mode. But it would be
beneficial when wpa_supplicant would behave similar to IBSS mode and set
this argument during mesh join like authsae already does. At least it is
helpful for companies/projects which are currently switching to 802.11s
(without mesh_fwding and with mesh_ttl set to 1) as replacement for IBSS
because newer drivers seem to support 802.11s but not IBSS anymore.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Simon Wunderlich <simon.wunderlich@openmesh.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [refresh]
Remove multicast routing firewall rules when the igmpproxy is stopped by
triggering a firewall config change.
Keeping the firewall open from the wan for igmp and udp multicast is not
desired when the igmpproxy service is inactive.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Check if the compiler defines __linux__, instead of assuming that the
host OS is the same as the target OS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update to latest Git in order to fix potential memory corruption and invalid
memory access when handling query strings in conjunction with active basic
authentication.
a235636 2017-11-04 file: fix query string handling
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
By default, hostapd assumes r1_key_holder equal to bssid. If LEDE
configures the same static r1 key holder ID on two different APs (BSSes) the
RRB exchanges fails behind them.
Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
Update wireguard to latest snapshot:
9fc5daf version: bump snapshot
748ca6b compat: unbreak unloading on kernels 4.6 through 4.9
7be9894 timers: switch to kees' new timer_list functions
6be9a66 wg-quick: save all hooks on save
752e7af version: bump snapshot
2cd9642 wg-quick: fsync the temporary file before renaming
b139499 wg-quick: allow for saving existing interface
582c201 contrib: add reresolve-dns
8e04be1 tools: correct type for CTRL_ATTR_FAMILY_ID
c138276 wg-quick: allow for the hatchet, but not by default
d03f2a0 global: use fewer BUG_ONs
6d681ce timers: guard entire setting in block
4bf32ca curve25519: only enable int128 if compiler support is sound
86e06a3 device: expand scope of destruct lock
e3661ab global: get rid of useless forward declarations
bedc77a device: only take reference if netns is different
7c07e22 wg-quick: remember to rewind DNS settings on failure
2352ec0 wg-quick: allow specifiying multiple hooks
573cb19 qemu: test using four cores
e09ec4d global: style nits
4d3deae qemu: work around ccache bugs
7491cd4 global: infuriating kernel iterator style
78e079c peer: store total number of peers instead of iterating
d4e2752 peer: get rid of peer_for_each magic
6cf12d1 compat: be sure to include header before testing
3ea08d8 qemu: allow for cross compilation
d467551 crypto/avx: make sure we can actually use ymm registers
c786c46 blake2: include headers for macros
328e386 global: accept decent check_patch.pl suggestions
a473592 compat: fix up stat calculation for udp tunnel
9d930f5 stats: more robust accounting
311ca62 selftest: initialize mutex in routingtable selftest
8a9a6d3 netns: use time-based test instead of quantity-based
e480068 netns: use read built-in instead of ncat hack for dmesg
Compile-tested-for: ar71xx
Run-tested-on: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit e7373e489d.
Support of "-s" depends on the CONFIG_DEBUG_SYSLOG compile time flag which
is not enabled for all build variants.
Revert the change for now until we can properly examine the size impact of
CONFIG_DEBUG_SYSLOG.
Fixes FS#1117.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous commit did not adjust PKG_RELEASE, therefore the
hostapd/wpad/wpa_supplicant packages containing the AP-side workaround
for KRACK do not appear as opkg update.
Bump the PKG_RELEASE to signify upgrades to downstream users.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is a simple version bump. Changes:
* noise: handshake constants can be read-only after init
* noise: no need to take the RCU lock if we're not dereferencing
* send: improve dead packet control flow
* receive: improve control flow
* socket: eliminate dead code
* device: our use of queues means this check is worthless
* device: no need to take lock for integer comparison
* blake2s: modernize API and have faster _final
* compat: support READ_ONCE
* compat: just make ro_after_init read_mostly
Assorted cleanups to the module, including nice things like marking our
precomputations as const.
* Makefile: even prettier output
* Makefile: do not clean before cloc
* selftest: better test index for rate limiter
* netns: disable accept_dad for all interfaces
Fixes in our testing and build infrastructure. Now works on the 4.14 rc
series.
* qemu: add build-only target
* qemu: work on ubuntu toolchain
* qemu: add more debugging options to main makefile
* qemu: simplify shutdown
* qemu: open /dev/console if we're started early
* qemu: phase out bitbanging
* qemu: always create directory before untarring
* qemu: newer packages
* qemu: put hvc directive into configuration
This is the beginning of working out a cross building test suite, so we do
several tricks to be less platform independent.
* tools: encoding: be more paranoid
* tools: retry resolution except when fatal
* tools: don't insist on having a private key
* tools: add pass example to wg-quick man page
* tools: style
* tools: newline after warning
* tools: account for padding being in zero attribute
Several important tools fixes, one of which suppresses a needless warning.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Commit 2127425434 introduced an AP-side
workaround for key reinstallation attacks. This option can be used to
mitigate KRACK on the station side, in case those stations cannot be
updated. Since many devices are out there will not receive an update
anytime soon (if at all), it makes sense to include this workaround.
Unfortunately this can cause interoperability issues and reduced
robustness of key negotiation, so disable the workaround by default, and
add an option to allow the user to enable it if he deems necessary.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The previous CVE bugfix commit did not adjust PKG_RELEASE, therefore the
fixed hostapd/wpad/wpa_supplicant packages do not appear as opkg update.
Bump the PKG_RELEASE to signify upgrades to downstream users.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This fixes a compile problem recently introduced by me.
Fixes: f40fd43ab2 ("ppp: fix compile warning")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move wireguard from openwrt/packages to base a package.
This follows the pattern of kmod-cake and openvpn. Cake is a fast-moving
experimental kernel module that many find essential and useful. The
other is a VPN client. Both are inside of core. When you combine the two
characteristics, you get WireGuard. Generally speaking, because of the
extremely lightweight nature and "stateless" configuration of WireGuard,
many view it as a core and essential utility, initiated at boot time
and immediately configured by netifd, much like the use of things like
GRE tunnels.
WireGuard has a backwards and forwards compatible Netlink API, which
means the userspace tools should work with both newer and older kernels
as things change. There should be no versioning requirements, therefore,
between kernel bumps and userspace package bumps.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Felix Fietkau <nbd@nbd.name>
This patch adds a parser for the uci representation of
dnsmasq's "-a | --listen-address" option.
In summary, this option forces dnsmasq to listen on the
given IP address(es). Both interface and listen-address
options may be given, in which case the set of both
interfaces and addresses is used.
Note that if no interface option is given, but listen_address is,
dnsmasq will not automatically listen on the loopback interface.
To achieve this, the loopback IP addresses, 127.0.0.1 and/or ::1
must be explicitly added.
This option is useful for ujailed dnsmasq instances, that would
otherwise fail to work properly, because listening to the
"This host on this network" address (aka 0.0.0.0 see rfc1700 page 4)
may not be allowed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (PKG_RELEASE increase)
A recent commit in hostapd added a build option to specify the default
TLS ciphers. This build option is passed via CFLAGS. Due to the way
CFLAGS are handled when building wpad, the compiler tries to recursively
expand TLS_DEFAULT_CIPHERS, resulting in the following error:
../src/crypto/tls_openssl.c: In function 'tls_init':
<command-line>:0:21: error: 'DEFAULT' undeclared (first use in this function)
../src/crypto/tls_openssl.c:1028:13: note: in expansion of macro 'TLS_DEFAULT_CIPHERS'
ciphers = TLS_DEFAULT_CIPHERS;
^
Escape double quotes in the .cflags file to avoid this.
Fixes: 2f78034c3e ("hostapd: update to version 2017-08-24")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is useful for tuning some more exotic parameters where it doesn't
make sense to attempt to cover everything in uci directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds config option to enable compression support which is usefull
when using a terminal sessions over a slow link. Impact on binary
size is negligible but additional 60 kB (uncompressed) is needed for
a shared zlib library.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
b84fdac Add debug output for service_timeout
8f7e3bc Remove incorrect comma in http service json config
9f40133 Remove ttl==255 restriction for queries
Signed-off-by: John Crispin <john@phrozen.org>
Fixes CVE-2017-12166: out of bounds write in key-method 1.
Remove the mirror that was temporarily added during the
2.4.3 release.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Update the config file to the latest version.
Added CONFIG_EAP_FAST=y because it was the only
missing flag about EAP compared to full config.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Other flags are the same as before.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Commented CONFIG_IEEE80211W=y flag because it is
set in the Makefile, only if the driver supports it.
Removed NEED_80211_COMMON flag because it is not part
of config file, it is set by the hostapd upstream Makefile.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update the config file to the latest version.
Enabled flags are the same as before.
Removed flag CONFIG_WPS2 because it is no more
needed due to this changelog (2014-06-04 - v2.2):
"remove WPS 1.0 only support, i.e., WSC 2.0
support is now enabled whenever CONFIG_WPS=y is set".
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[add punctuation to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
3fd58e9 2017-08-19 uhttpd: add manifest support
88c0b4b 2017-07-09 file: fix basic auth regression
99957f6 2017-07-02 file: remove unused "auth" member from struct
path_info
c0a569d 2017-07-02 proc: expose HTTP_AUTH_USER and HTTP_AUTH_PASS
ad93be7 2017-07-02 auth: store parsed username and password
fa51d7f 2017-07-02 proc: do not declare empty process variables
a8bf9c0 2017-01-26 uhttpd: Add TCP_FASTOPEN support
e6cfc91 2016-10-25 lua: ensure that PATH_INFO starts with a slash
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
This option is used to specify a file containing PEM certs, to complete the
local certificate chain. Which is quite usefull for "split-CA" setups.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Add support for ft_psk_generate_local flag in ieee80211r
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[original author]
Signed-off-by: Sergio <mailbox@sergio.spb.ru>
Init script won't append --no-dhcp-interface option if interface
protocol is one of: ncm, directip, qmi, mbim.
This is caused by IP address assigned to dynamically created netifd
interfaces. As a result there's no netmask assigned to the main
interface and dhcp_add() function returns prematurely.
By moving network subnet check we can ensure that --no-dhcp-interface is
properly generated for wwan interfaces.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase; move network checks]
With the introduction of the ubus notifications, we would now fail building
dnsmasq with external toolchains that don't automatically search for headers.
Pass TARGET_CPPFLAGS to the Makefile to resolve that.
Fixes: 34a206bc11 ("dnsmasq: add ubus notifications for new leases")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Instead of blindly enabling the odhcpd v6 server and RA server on the
lan port, only do that if the lan port protocol is "static"
This prevents the unhelpful case of a device being a dhcpv4 client and
v6 server on the same ethernet port.
Signed-off-by: Karl Palsson <karlp@etactica.com>
[PKG_SOURCE_DATE increase; odhcpd.defaults script cleanup]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Fix multiple syntax errors in shelscripts (of packages only)
These errors were causing many conditions to not working properly
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
[increase PKG_RELEASE, drop command substitution from directip.sh]
Signed-off-by: Mathias Kresin <dev@kresin.em>
ifname variable were not assigned due to syntax error
causing the hostapd config file to have an empty iapp_interface= option
Signed-off-by: Lorenzo Santina <lorenzo.santina.dev@gmail.com>
Don't return arcount=1 if EDNS0 RR won't fit in the packet.
Omitting the EDNS0 RR but setting arcount gives a malformed packet.
Also, don't accept UDP packet size less than 512 in received EDNS0.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Remove LEDE partial fix for CVE-2017-13704.
Backport official fix from upstream.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (PKG_RELEASE increase)
ssh and scp commands interfere with OpenSSH when installed in /usr/bin .
One use case is when installing dropbear to get root access when only OpenSSH is available (OpenSSH disallows root password logins). Once dropbear installs, it replaces OpenSSH's executables, even when removed with opkg. OpenSSH must be reinstalled to get them back.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
printer support is removed using 200-remove_printer_support.patch. the syslog parameter requires samba to be compiled with --with-syslog. Currently samba does not log to syslog and probably has not for a long time.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
It's redundant and also buggy. IPv6 link local addresses and ::1 are not resolved for example. Doesn't matter since lo and br-lan for example, resolve to them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
guest ok is set per share and as such, don't override it. also, fix an error introduced in the last commit.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fix SIGSEGV in rfc1035.c answer_request() line 1228 where memset()
is called with header & limit pointing at the same address and thus
tries to clear memory from before the buffer begins.
answer_request() is called with an invalid edns packet size provided by
the client. Ensure the udp_size provided by the client is bounded by
512 and configured maximum as per RFC 6891 6.2.3 "Values lower than 512
MUST be treated as equal to 512"
The client that exposed the problem provided a payload udp size of 0.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Currently, dnsmasq support assigning multiple tags to a host record
(--dhcp-host), but we only support only 1 tag for a host. The commit
makes the following config to be valid:
config host
option name 'computer'
option mac '00:11:22:33:44:55'
option ip '192.168.1.100'
list tag 'vendor_class'
list tag 'vendor_id'
config tag 'vendor_class'
list dhcp_option 'option:vendor-class,00:...<omitted>'
config tag 'vendor_id'
option force '1'
list dhcp_option 'option:vendor-id-encap,00:...<omitted>'
Signed-off-by: Kuang Rufan <kuangrufan@pset.suntec.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Samba could also be usefull for sending commands to windows pc (like shoutdown command). This new package add the bin to include this kind of command to the samba package.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
94e65ee ndp: use IPv4 address list when comparing IPv4 addresses
ff5020d dhcpv6-ia: rework reconfigure accept logic
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
While debugging an issue with a client device, wpa_supplicant did not
seem to log anything at all. Make wpa_supplicant log to syslog instead
of stdout, to make debugging easier and to be consistent with hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
296b4a0 dhcpv6: assign all viable DHCPv6 addresses by default (FS#402, FS#524)
f4d38e0 treewide: reflect managed mode is related to RA
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Browseable is now set through LuCI per share, so remove it. Same with
writeable (inverted synonym for read only). domain master and preferred
master seem to be legacy settings for Windows 9x. encrypt passwords
defaults to yes. Probably should not be disabled either.
Also reordered alphabetically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[rewrap commit message, fix SoB, fix author, bump pkg revsion]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce a new UCI list setting `list dhcp_option_force` which is available
in sections of type `dnsmasq` and `dhcp`.
The `dhcp_option_force` setting has the same semantics as `dhcp_option` but
generates `dhcp-option-force` directives instead of `dhcp-option` ones in
emitted native configuration.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Remove ping check in DHCPDISCOVER case as too many buggy clients leave
an interface in configured state causing the ping check to fail.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Commit 5cd88f4 "dnsmasq: remove use of uci state for getting network ifname"
broke the ability to specify unmanaged network device names for inclusion
and exclusion in the uci configuration.
Restore support for raw device names by falling back to the input value
when "network_get_device" yields no result.
Fixes FS#876.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
f0d78e7 ndp: optimize check_addr6_updates code
94afe3b ndp: fix syslog tracing for netlink neigbor and address events
18df6cc treewide: rework logic to retrieve IPv6 interface addresses
803b83e router: use enum to specify order and index of iov struct
5dad295 treewide: rework code to get rid of fixed IPv6 address arrays
3e4c8ad config: rework code to get rid of IFNAMSIZ usage
ab7813e treewide: use angle-brackets to include libubox header files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This is functionally the same as --server, but provides some syntactic sugar to
make specifying address-to-name queries easier.
For example --rev-server=1.2.3.0/24,192.168.0.1 is exactly equivalent to
--server=/3.2.1.in-addr.arpa/192.168.0.1
Signed-off-by: DUPONCHEEL Sébastien <sebastien.duponcheel@corp.ovh.com>
Backport upstream dnsmasq patch fixing DNS failover when first servers
returns REFUSED in strict mode; fixes issue FS#841.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add a uci option to set the new max auth tries paramater in dropbear.
Set the default to 3, as 10 seems excessive.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for '-T n' for a run-time specification for maximum number
of authentication attempts where 'n' is between 1 and compile time
option MAX_AUTH_TRIES.
A default number of tries can be specified at compile time using
'DEFAULT_AUTH_TRIES' which itself defaults to MAX_AUTH_TRIES for
backwards compatibility.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
RADIUS protocol could be used not only for authentication but for
accounting too. Accounting could be configured for any type of networks.
However there is no way to configure NAS Identifier for non-WPA
networks without this patch.
Signed-off-by: Yury Shvedov <yshvedov@wimarksystems.com>
[cleanup commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Don't start ping-check of address in DHCP discover if there already
exists a lease for the address. It has been reported under some
circumstances android and netbooted windows devices can reply to
ICMP pings if they have a lease and thus block the allocation of
the IP address the device already has during boot.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
During auto channel selection we may wish to prefer certain channels
over others.
e.g. we can just squeeze 4 channels into europe so '1:0.8 5:0.8 9:0.8
13:0.8' does that.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
dnsmasq can match tags in its dhcp-range configuration, this commit adds
the option to configure it in the dhcp section
uci configuration:
config dhcp 'lan'
option interface 'lan'
list tag 'blue'
list tag '!red'
option start '10'
option limit '150'
option leasetime '12h'
generated dnsmasq configuration:
dhcp-range=tag:blue,tag:!red,set:lan,192.168.1.10,192.168.1.159,255.255.255.0,12h
Signed-off-by: Grégoire Delattre <gregoire.delattre@gmail.com>
With this patch the dnsmasq init script manages resolv.conf if and only if
when dnsmasq will listen on 127.0.0.1#53 (is main resolver instance).
Also, resolvfile is now set irrespective of the value of noresolv.
Fixes (partially) FS#785
Signed-off-by: Paul Oranje <por@xs4all.nl>
'non-wildcard' interfaces enables dnsmasq's '--bind-dynamic' mode. This
binds to interfaces rather than wildcard addresses *and* keeps track of
interface comings/goings via a unique Linux api.
Quoting dnsmasq's author "bind-dynamic (bind individual addresses, keep
up with changes in interface config) ... On linux, there's actually no
sane reason not to use --bind-dynamic, and it's only not the default for
historical reasons."
Let's change history, well on LEDE at least, and change the default!
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Commit b32689afd6 added support for dhcp-script hook.
Adding dhcp-script config option results into two instances of dnsmasq being run
which triggered oom issues on platforms having low memory.
The dnsmasq dhcp-script config option will now only be added if at least one of the
dhcp, tftp, neigh hotplug dirs has a regular hotplug file or if the dhcpscript uci
config option is specified.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The umdns init script includes function/network.sh globally, outside of any
service procedure. This causes init script activation to fail in buildroot
and IB context if umdns is set to builtin.
Additionally, the network.sh helper is not actually used.
Drop the entire include in order to repair init script activation in build
host context. Fixes FS#658.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Assign the virtual DHCPv6 interface the firewall zone of the parent interface
so fw3 knows the zone to which the virtual DHCPv6 interface belongs.
This guarantees the firewall settings are applied correctly for the virtual
DHCPv6 interface and allows to query the zone to which the virtual DHCPv6
interface belongs via the fw3 network option.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
easy-rsa v3 is now a single script. It expects a 'vars'
configuration file which path can be set using easy-rsa
options, environment variables or just looking in the
current directory.
The default usage would be:
# cd /etc/easy-rsa
# easy-rsa COMMAND [command-options]
Following upstream changes, /etc/easy-rsa/pki replaces
/etc/easy-rsa/keys directory.
The default /etc/easy-rsa/pki dir is marked to be kept during
upgrade (WARN: priv keys are saved in the system backup)
/etc/easy-rsa/openssl.1.0.cnf is now marked as config file while
index and serial got removed.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The previous CVE bugfix commit did not adjust PKG_RELEASE, therefor the
fixed samba package does not appear as opkg update.
Bump the PKG_RELEASE to signify upgrades to downstream users.
Ref: https://forum.lede-project.org/t/sambacry-are-lede-devices-affected/3972/4
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Adds a script which acts as a hook for when dnsmasq creates/destroys a
lease, or completes a TFTP file transfer. The hook loops through scripts
in appropriate directories inside '/etc/hotplug.d', executing each one with
the same arguments supplied by dnsmasq.
In case dnsmasq is jailed by ujail the dhcp-script hook will not work as
expected as ujail does not yet support executing a script within a jail.
Signed-off-by: Nick Brassel <nick@tzarc.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Some small tweaks and improvements :
9828ab1 Fix compiler warning.
f77700a Fix compiler warning.
0fbd980 Fix compiler warning.
43cdf1c Remove automatic IDN support when building i18n.
ff19b1a Fix &/&& confusion.
2aaea18 Add .gitattributes to substitute VERSION on export.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This includes following changes:
0e8b948 Support specifying instance name in JSON file
49fdb9f Support PTR queries for a specific service
26ce7dc Allow filtering with instance name in service_reply
920c62a Store instance name in the struct service
ff09d9a Rename service_name function to the service_instance_name
64f78f1 Rename mdns_hostname variable to the umdns_host_label
Previous package update pulled commit 70c66fbbcde86 ("Fix sending
replies to PTR questions") which introduced a regression which this
update fixes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
- Security: Fix double-free in server TCP listener cleanup A double-free
in the server could be triggered by an authenticated user if dropbear is
running with -a (Allow connections to forwarded ports from any host)
This could potentially allow arbitrary code execution as root by an
authenticated user. Affects versions 2013.56 to 2016.74. Thanks to Mark
Shepard for reporting the crash.
CVE-2017-9078 https://secure.ucc.asn.au/hg/dropbear/rev/c8114a48837c
- Security: Fix information disclosure with ~/.ssh/authorized_keys
symlink. Dropbear parsed authorized_keys as root, even if it were a
symlink. The fix is to switch to user permissions when opening
authorized_keys
A user could symlink their ~/.ssh/authorized_keys to a root-owned file
they couldn't normally read. If they managed to get that file to contain
valid authorized_keys with command= options it might be possible to read
other contents of that file.
This information disclosure is to an already authenticated user.
Thanks to Jann Horn of Google Project Zero for reporting this.
CVE-2017-9079 https://secure.ucc.asn.au/hg/dropbear/rev/0d889b068123
Refresh patches, rework 100-pubkey_path.patch to work with new
authorized_keys validation.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
I think I added these respawn params [a while back],
when I did the conversion to procd init script format.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
When in ra server mode, configure nameservers passed in router
announcements from the dns value (which is already used by odhcpd).
This also fixes FS#677 by using the global IPv6 address of the router
instead of the link local address (if no nameservers are configured).
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
We enabled lua interpreter by default as it doesn't make any problem in the uhttpd config file and we modify the index page to use it.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
93abe6f config: fix invalid hoplimit in RA message
2ae08d1 config: fix invalid retranstime in RA message
0005cb4 config: fix invalid reachabletime in RA message
5683dd2 config: limit ra_mtu to 65535
f8d40a5 router: fix interface mtu read error
f8f4b87 config: limit ra_retranstime to 60000
a2d8bf6 dhcpv4: display two hex digits per octet in syslog
a9e9bc4 config: make RA retransTime configurable via uci
2cb6b48 config: make RA reachableTime configurable via uci
e4504db config: make RA curHopLimit configurable via uci
9dd5316 config: make RA mtu configurable via UCI
29cb2ff config: fix dhcpv4 server being started
0ef74ec ndp.c: add switch/case fallthrough comments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This patch adds the interface-name option for each dhcp config
in /etc/config/dhcp.
With the interface_name option users can define a DNS name for each dhcp section
that will be resolved by dnsmasq with the underlaying interface address.
For example:
config dhcp 'lan'
option interface 'lan'
...
list interface_name 'home.lan'
...
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If there's a TFTP root directory configured, create it with mkdir -p
(which does not throw an error if the folder exists already)
before starting dnsmasq. This is useful for TFTP roots in /tmp, for example.
Originally submitted by nfw user aka Nathaniel Wesley Filardo
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
A number of small tweaks & improvements on the way to a final release.
Most notable:
Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
9268ca6 ndp: don't trigger IPv6 ping when neighbor entry is invalid
2b3355f ndp: fix adding proxy neighbor entries
7dff5b4 ndp: fix wrong interface name in syslog message
a54afb5 dhcpv6-ia: Fix segfault when writing DHCPv4 leases in state file
c0e9dbf ubus: don't segfault when there're no leases
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Configuring dhcp_option as an option does not allow the usage of white
spaces in the option value; fix this by supporting dhcp_option as a list
config while still supporting the option config to maintain backwards
compatibility
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Install procd interface triggers only for interfaces which are enabled
so dropbear instances running on (an) enabled interface(s) are not
restarted due to an interface trigger of an interface which is disabled.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
minor/cosmetic: fixes the following misleading message:
root@box:~ /etc/init.d/dnsmasq restart
sh: out of range
Signed-off-by: Bastian Bittorf <bb@npl.de>
Update OpenVPN to 2.4.1
Remove 200-small_build_enable_occ.patch as it's included upstream.
Refresh patches
Add mirror and switch to HTTPS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Similar to odhcpd, allow using ISC DHCPd instead of dnsmasq.
Disable DHCP and/or DHCP6 in case ISC DHCP is present and
enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This includes following changes:
480d7bc Fix sending unicast questions on cache expire
a0403cd Keep source sockaddr for every cached DNS record
1478293 Fix code freeing cached non-A(AAA) records too early
9f1cc22 Fix replying to "QU" questions received on unicast interface
943bedb Fix reading port of incoming packets
c725494 Use MCAST_PORT define for port 5353
ce7e9e9 Use one define for DNS-Based Service Discovery service name
e1bacef Drop entries cached for interface we're going to delete
496aeba Fix comment typo in cache_gc_timer
f89986b Fix refreshing cached A(AAA) records that expire
Previous updates made umdns work as expected on startup but there were
still many bugs. They were mostly related to runtime - cache management
and requests + responses. E.g. umdns was never able to send question on
DNS record expire. It was also ignoring all incoming unicast questions.
Since these issues are quite serious it makes sense to backport this
update to the stable branch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If noresolv is set, we should not generate a --resolv-file parameter.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [minor cleanup]
This includes 3 cleanups:
fd5a160 Don't cache hosts as services
80dd246 Refresh DNS records A and AAAA directly
6515101 Access cached records (instead of services) to read list of hosts
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes crash in interface_start caused by freeing interface in
interface_free without stopping a timeout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
RFC 6761 defines a number of top level domains should not be forwarded
to the Internet's domain servers since they are not responsible for
those domains.
This change adds a list of domains that will be blocked when 'boguspriv'
is used and augments that which is already blocked by dnsmasq's notion
of 'local service' using '--bogus-priv' i.e. RFC 1918 private addresses
and IPv6 prefixes as defined in RFC 6303.
To make this configurable rather than hard coded in dnsmasq's init
script, a new file /usr/share/dnsmasq/rfc6761.conf is conditionally
included.
The default file matches the RFC 6761 recommendation along with a few
other top level domains that should not be forwarded to the Internet.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Honour the parent interfaces peerdns option when spawning a virtual DHCPv6
interface in order to avoid pulling in IPv6 DNS servers when the user opted
to inhibit peer DNS servers in the configuration.
Fixes#597.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
--bogus-priv now applies to IPv6 prefixes as specified in RFC6303 - this
is significantly friendlier to upstream servers.
CNAME fix in auth mode - A domain can only have a CNAME if it has no
other records
Drop 2 patches now included upstream.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
- Fix eap test to work with standalone hostapd builds
- Fix 11n test to check the correct define
- Add 11ac, 11r and 11w tests
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
New test release (since test1) includes 2 LEDE patches that are
upstream and may be dropped, along with many spelling fixes.
Add forthcoming 2017 root zone trust anchor to trust-anchors.conf.
Backport 2 patches that just missed test3:
Reduce logspam of those domains handled locally 'local addresses only'
Implement RFC-6842 (Client-ids in DHCP replies)
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
as we do for IPv4 PPP interfaces. When we create the
dynamic IPv6 interface we should inherit ip6table from
main interface.
Signed-off-by: Ulrich Weber <ulrich.weber@riverbed.com>
pppoe-discovery performs the same discovery process as pppoe, but does
not initiate a session
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The only HMACs currently available use MD5 and SHA1, both of which have known
weaknesses. We already compile in the SHA256 code since we use Curve25519
by default, so there's no significant size penalty to enabling this.
Signed-off-by: Joseph C. Sible <josephcsible@users.noreply.github.com>
Bump to dnsmasq 2.77test1 - this includes a number of fixes since 2.76
and allows dropping of 2 LEDE carried patches.
Notable fix in rrfilter code when talking to Nominum's DNS servers
especially with DNSSEC.
A patch to switch dnsmasq back to 'soft fail' for SERVFAIL responses
from dns servers is also included. This mean dnsmasq tries all
configured servers before giving up.
A 'localise queries' enhancement has also been backported (it will
appear in test2/rc'n') this is especially important if using the
recently imported to LEDE 'use dnsmasq standalone' feature 9525743c
I have been following dnsmasq HEAD ever since 2.76 release.
Compile & Run tested: ar71xx, Archer C7 v2
Tested-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ref commit 9525743c07
dnsmasq: make DHCPv6 viable for standalone dnsmasq install
Above commit broke instancing by missing filter_dnsmasq()
as part of the dhcp_add() execution.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Do not spam the syslog with DHCPv6 lease info if quietdhcp option
is selected. This already works for DHCPv4, make it work in the same
way for DHCPv6.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
[Originally written by Arjen de Korte on GitHub but had issues providing
a SoB in correct format.]
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
key_direction shows up as an openvpn option in the user-interface but does not end up in the /var/etc/openvpn*.conf file. Adding it to the list here fixed the issue for me.
Signed-off-by: Brandon Koepke <bdkoepke@fastmail.com>
samba.org has started to enforce https and
currently plain http downloads with curl/wget fail,
so convert samba.org download links to use https.
Modernise links at the same time.
Also convert samba.org URL fields to have https.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
dnsmasq has sufficient services to meet the needs of DHCP
and RA with IP6 for single router router users. This is
the most common use for consumer routers. Its reenforced
as most ISP tend to only DHCP-PD /64. dnsmasq has year
over year demonstrated great flexibility in its option
set, and support for off-standard DHCP clients.
odhcpd has enhanced capabilities focused on IP6 such
as DHCP/RA relay and NDP proxy. However, it is not as
flexible in its option set. odhcpd is not as forgiving
with off-standard DHCP clients. Some points may represent
a long term TODO list, but it is the state currently.
These changes make any such combination possible. Already
odhcpd can be set as the main dhcp server. Now odhcpd
can be removed or disabled and dnsmasq will take over
if DHCPv6 compiled in. The existing DHCPv6 and RA UCI
are translated into dnsmasq.conf. The changes focus on
'--dhcp-range', '--dhcp-host', and '--dhcp-options'.
DHCP host ID is least 16 bits [::1000-::FFFF], but
leaves low range for typical infrastructure assignments.
dnsmasq accepts DHCPv6 options in the tranditional
'--dhcp-option' put they must be prefixed 'option6:'.
dnsmasq will also discover SLAAC DNS entries from DHCPv4
clients MAC, and confirm with a ping at least renew.
Long term TODO include improving use of dnsmasq relay
options for DHCPv4 and DHCPv6 in parallel. It would also
be possible to preconfigure DHCP-PD in host-with-options
records for fixed infrastructure.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
[Jo-Philipp Wich: emit proper IPv6 hostid format in dhcp-host directive]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ref commit 612e2276b4
ref commit ec63e3bf13
'option add_local_hostname' scripted implementation statically assigns
this host in auto generated host file at init. If IFUP or other signals
do not occur, then address changes are not tracked. The script doesn't
apply all the addresses at an interface. This may make logs obscure.
The script only puts the bare host name (maybe not FQDN) in host file,
but if '--exapandhosts' is enabled, then /etc/hosts entries will be
suffixed, and "127.0.0.1 localhost" becomes "localhost.lan".
dnsmasq provides an option to perform this function, but it is rather
greedy. '--interface-name=<name>,<iface>' will assign the name to all
IP on the specified interface (except link local). This is a useful
feature, but some setups depend on the original restrictive behavior.
'option add_local_fqdn' is added to enhance the feature set, but
if not entered or empty string, then it will default to original
option and behavior. This new option has a few settings. At each
increased setting the most detailed name becomes the PTR record:
0 - same as add_local_hostname 0 or disabled
1 - same as add_local_hostname 1
2 - assigns the bare host name to all IP w/ --dnsmasq-interface
3 - assigns the FQDN and host to all IP w/ --dnsmasq-interface
4 - assigns <iface>.<host>.<domain> and above w/ --dnsmasq-nterface
'option add_wan_fqdn' is added to run the same procedure on
inferred WAN intefaces. If an interface has 'config dhcp' and
'option ignore 1' set, then it is considered WAN. The original
option would only run on DHCP serving interfaces.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
This will allow starting hostapd with the new -s parameter and finally
read all (error) messages from the syslog.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It wasn't possible to read hostapd wpa_printf messages unless running
hostapd manually. It was because hostapd was printing them using vprintf
and not directly to the syslog.
We were trying to workaround this problem by redirecting STDIN_FILENO
and STDOUT_FILENO but it was working only for the initialization phase.
As soon as hostapd did os_daemonize our solution stopped working.
Please note despite the subject this change doesn't affect debug level
messages only but just everything printed by hostapd with wpa_printf
including MSG_ERROR-s. This makes it even more important as reading
error messages can be quite useful for debugging.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Updates to openvpn.init were included in early OpenVPN 2.4 patch
series, but got lost along the way and were never merged.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
When relying on x.509 certs for auth and / or encryption of traffic you can't
use package openvpn-nossl.
Just have your package depend on openvpn-crypto to have SSL-encryption and
X.509-support enabled in OpenVPN. If encryption / X.509 is not a must, use
virtual packge openvpn, which is provided by all OpenVPN-variants.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
ap_setup_locked is named wps_ap_setup_locked in uci for consistency with other
wps related uci options.
Signed-off-by: Steven Honson <steven@honson.id.au>
The hostapd_append_wpa_key_mgmt() procedure uses the possibly uninitialized
$ieee80211r and $ieee80211w variables in a numerical comparisation, leading
to stray "netifd: radio0 (0000): sh: out of range" errors in logread when
WPA-PSK security is enabled.
Ensure that those variables are substituted with a default value in order to
avoid emitting this (harmless) shell error.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add PROVIDES:=openvpn to the default recipe in order to let all build variants
provide a virtual openvpn package.
The advantage of this approach is that downstream packages can depend on just
"openvpn" without having to require a specific flavor.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This causes problem when a FQDN is configured in /etc/config/system. The
domain name will appear twice in reverse DNS.
Next to that, there seems to be a bug in dnsmasq. From the manual page:
--interface-name=<name>,<interface>[/4|/6]
Return a DNS record associating the name with the primary address
on the given interface. This flag specifies an A or AAAA record for the
given name in the same way as an /etc/hosts line, except that the address
is not constant, but taken from the given interface. The interface may be
followed by "/4" or "/6" to specify that only IPv4 or IPv6 addresses
of the interface should be used. If the interface is down, not configured
or non-existent, an empty record is returned. The matching PTR record is
also created, mapping the interface address to the name. More than one name
may be associated with an interface address by repeating the flag; in that
case the first instance is used for the reverse address-to-name mapping.
It does not just create an A/AAAA record for the primary address, it creates
one for all addresses. And what is worse, it seems to actually resolve to the
non-primary address first. This is quite annoying when you use floating IP
addresses (e.g. VRRP), because when the floating IP is on the other device,
SSH failes due to incorrect entry in the known hosts file.
I know that this is not a common setup, but it would be nice if there was an
option to restore the previous behaviour, rather than just forcing this new
feature on everybody.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
wpa_supplicant allows only SAE as the key management
type for mesh mode. The recent key_mgmt rework unconditionally
added WPA-PSK - this breaks interface bringup and wpa_s
throws this error message:
Line 10: key_mgmt for mesh network should be open or SAE
Line 10: failed to parse network block.
Failed to read or parse configuration '/var/run/wpa_supplicant-wlan0.conf
Fix this by making sure that only SAE is used for mesh.
Signed-off-by: Sujith Manoharan <m.sujith@gmail.com>
Enabling this makes it possible to query LLDP neighbors via SNMP.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
ef3c563 dhcpv6-ia: filter out prefixes having invalid length
16cd87e dhcpv6-ia: fix dereference after freeing assignment
d6b0c99 dhcpv6-ia: log only IPv6 addresses which are effectively
assigned to a DHCPv6 client
08a9367 config: respect ignore uci option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
'add_local_hostname' previous implementation may drop some addresses.
Soft addition of IP6 addresses may not cause a reload or restart event.
dnsmasq '--interface-name' robustly applies DNS to all addresses per
interface (except fe80::/10).
Change UCI 'add_local_hostname' to expand during each interface assignement
during add_dhcp().
Assign '<iface>.<host>.<domain>' as true name (reflexive A, AAAA, and PTR).
Assign '<host>.<domain>' and '<host>' as convinience aliases (no PTR, not
technically CNAME).
This is accomplished with the '--interface-name' order, first is PTR.
We could also assign each <ip4/6>.<iface>.<host>.<domain> to the respective
dual stack on the interface.
That seemed excessive so it was skipped (/4 or /6 suffix to the interface).
Add UCI 'add_wan_hostname' similar to 'add_local_hostname' function for
external WAN.
WAN IP4 are less often named by the ISP and rarely WAN IP6 due to complexity.
For logs, LuCI connection graph, and other uses assigning a WAN name is desired.
'add_local_hostname' only applies with DHCP and 'add_wam_hostname' only applies
without DHCP. Common residential users will want to set both options TRUE.
Businesses will probably have global DNS, static IP, and 'add_wan_hostname' FALSE.
Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
Add DHCPv6 matching by DHCP Unique Identifier (RFC-3315) in addition to
existing MAC-address (RFC-6939). The latter is not widely supported yet.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
Enable support for stronger SHA256-based algorithms in hostapd and
wpa_supplicant when using WPA-EAP or WPA-PSK with 802.11w enabled.
We cannot unconditionally enable it, as it requires hostapd to be
compiled with 802.11w support, which is disabled in the -mini variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Now that wpa_key_mgmt handling for hostapd and wpa_supplicant are
consistent, we can move parts of it to a dedicated function.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Rework wpa_key_mgmt handling for wpa_supplicant to be consistent with
how it is done for hostapd.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
add possibility to set the facility to which dnsmasq will send syslog entries, i.e. set it to '/dev/null' to mute dnsmasq output at all.
Signed-off-by: Dirk Brenken dev@brenken.org
Before the rewrite, uhttpd-mod-tls used to contain a tls plugin.
Afterwards it was left in for compatibility reasons, but given how much
has changed, and that we're about to change the default SSL
implementation again, it's better to just drop this now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
OpenVPN 2.4 builds with mbedTLS 2.x, rename openvpn-polarssl
variant to openvpn-mbedtls.
Some feature highlights:
* Data channel cipher negotiation
* AEAD cipher support for data channel encryption (currently only
* AES-GCM)
* ECDH key exchange for control channel
* LZ4 compression support
See https://github.com/OpenVPN/openvpn/blob/master/Changes.rst
for additional change notes.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Let dnsmasq reread the leasefile by using procd_send_signal
which triggers procd to send SIGHUP kill signal by default
if signal is not specified
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest upstream HEAD:
- Refreshed all
- Delete patches and parts which made it upstream
Compile tested Full & Mini configs
Run-tested Mini config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [another update, remove broken patch]
The build system only accepts Package/<name>/description and since the
typoed version virtually has the same content as the TITLE field, remove
them altogether
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The SIGHUP also got sent to the reload script making it bail out
with an error
Revert "dnsmasq: reload config if host name is modified"
This reverts commit 854459a2f9.
Reported-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
The sha256sum was not updated in the last commit.
Fixes: a7c231027 [odhcpd: Fix dnsmasq re-reading hostfile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Harmonise handling of DEFAULT_PATH by removing the patch introducing #ifndef
guards around the path, and only using one means to set the path in the
makefile.
Signed-off-by: Dario Ernst <Dario.Ernst@riverbed.com>
Depending on the dhcp uci config pidof dnsmasq can return
multiple pids. Fix re-reading of the hostfile by dnsmasq in
such case by sending SIGHUP signal to each of the returned
pids.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Let dnsmasq read all hosts files in /tmp/hosts directory by specifying
/tmp/hosts as argument of --addn-host
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
OpenVPN requires arguments to --push to be enclosed in double quotes.
One set of quotes is stripped when the UCI config is parsed.
Change append_params() of openvpn.init to enclose push parameters in
double quotes.
Unquoted push parameters do not cause errors in OpenVPN 2.3,
but OpenVPN 2.4 fails to start with unquoted push parameters.
Fixes: FS#290.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Correct splitting the 32-bit 'hostid' value to two 16-bit hexadecimal
values. Previously, the lower 16-bit value was truncated to an 8-bit
value, which would result in hostid values 100 and 200 both to be set
to [::0:0] instead of [::0:100] and [::0:200] respectively.
Signed-off-by: Arjen de Korte <build+lede@de-korte.org>
If the hostname in /etc/config/system is modified the dnsmasq will not
reread the update host file under /tmp/hosts/dhcp.$cfg.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
odhcpd daemon has hitless config reload support by means of the
sighup signal; add reload_service function which uses sighup
signal to reload the config
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adds the mac address of the DNS requestor to DNS queries which
are forwarded upstream and can be used to do filtering by the
upstream servers. This only works if the requestor is on the
same subnet as the dnsmasq server
The addmac parameter can hold the following values:
0 : mac address is not added
1 : mac address is added in binary format
base64 : mac address is added base64 encoded
text: : mac address is added in human readable format
as hex and colons
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Ensure that selecting the wpa-supplicant-mesh package actually packages the
wpa_supplicant binary with SAE support and add missing dependency on OpenSSL.
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: slightly reword commit message for clarity]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We add an 'httpauth' section type that contains the options:
prefix: What virtual or real URL is being protected
username: The username for the Basic Auth dialogue
password: Hashed (crypt()) or plaintext password for the Basic Auth dialogue
httpauth section names are given included as list
items to the instances to which they are to be applied.
Further any existing httpd.conf file (really whatever
is configured in the instance, but default of
/etc/httpd.conf) is appended to the per-instance httpd.conf
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
During reload, we could send invalid information to the other
side and confuse it.
That's why, during reload we'll pause execution, do the reconfig
and resume + update when reload is done.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The problem is that interfaces are specified at start as
command line arguments, making them unchange-able via reload.
That means, we have to move (since lldpd allows this) the
interfaces-match-pattern option to be in a config file and reload
the configuration.
It's either that, or do a 'restart'.
Since we're generating the lldpd.conf file, we'll have to
move the 'sysconfdir' of lldpd to /tmp, where the files will
get written ; this will prevent any unncessary flash writes.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds support in uci for configuring multiple dnsmasq instances via
multiple dnsmasq sections.
The uci sections host, boot, mac, tag, vendorclass, userclass,
circuitid, ... will refer to a dnsmasq instance via the instance
parameter defined in the section; if the instance parameter is
not specified backwards compatibility is preserved.
Start/Stopping a dnsmasq instance can be achieved by passing the
dnsmasq instance name as argument to start/stop via the init script.
Multiple dnsmasq instances is usefull in scenarios where you want to
bind a dnsmasq instance to an interface in order to isolate networks.
This patch is a rework of a multiple dnsmasq instance patch by Daniel Dickinson
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add a partially random O= item to the certificate subject in order
to make the automatically generated certificates' subjects unique.
Firefox has problems when several self-signed certificates
with CA:true attribute and identical subjects have been
seen (and stored) by the browser. Reference to upstream bugs:
https://bugzilla.mozilla.org/show_bug.cgi?id=1147544https://bugzilla.mozilla.org/show_bug.cgi?id=1056341https://bugzilla.redhat.com/show_bug.cgi?id=1204670#c34
Certificates created by the OpenSSL one-liner fall into that category.
Avoid identical certificate subjects by including a new 'O=' item
with CommonName + a random part (8 chars). Example:
/CN=LEDE/O=LEDEb986be0b/L=Unknown/ST=Somewhere/C=ZZ
That ensures that the browser properly sees the accumulating
certificates as separate items and does not spend time
trying to form a trust chain from them.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prefer the old default 'px5g' for certificate creation
as Firefox seems to dislike OpenSSL-created certs.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The special prefix of "/" should match any url by definition but the final
assertion which ensures that the matched prefix ends in '\0' or '/' is causing
matches against the "/" prefix to fail.
Update to current HEAD in order to fix this particular case.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This more of a demo for the previous commit that comes with
this one, where I added support for copying source from 'src' to
the build dir(s).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds per-host leasetime support
Various bugfixes :
-Prioritize ifname resolving via ubus
-Free interface if ifindex cannot be resolved
-...
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [update mirror sha256]
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Now that the uhttpd init script can generate certificates using openssl as
well, update the section name and related comment to be more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support the usage of the OpenSSL command-line tool for generating
the SSL certificate for uhttpd. Traditionally 'px5g' based on
PolarSSL (or mbedTLS in LEDE), has been used for the creation.
uhttpd init script is enhanced by adding detection of an installed
openssl command-line binary (provided by 'openssl-util' package),
and if found, the tool is used for certificate generation.
Note: After this patch the script prefers to use the OpenSSL tool
if both it and px5g are installed.
This enables creating a truly OpenSSL-only version of LuCI
without dependency to PolarSSL/mbedTLS based px5g.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Configurations without shadow passwords have been broken since the removal
of telnet: as the default entry in /etc/passwd is not empty (but rather
unset), there will be no way to log onto such a system by default. As
disabling shadow passwords is not useful anyways, remove this configuration
option.
The config symbol is kept (for a while), as packages from feeds depend on
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
