Splits up DEVICE_TITLE into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT.
Fixes https://github.com/openwrt/openwrt/pull/2245
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Support added to bcm2709 subtarget (32 bit).
- 64 bit kernel still requires many hacks on RPi 4B.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch adds the boot-part feature which enables the brcm2708
target move from the custom boot partition size config option to
the generic CONFIG_TARGET_KERNEL_PARTSIZE.
Note:
For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value
can cause sysupgrade to repartition the device!
Make sure to have a backup in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89
Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""
Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch
Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.
Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
To be able to use the camera module, start_x=1 has to be set in
config.txt. This will cause the bootloader to load the GPU firmware that
contain the extra video codecs. Install these firmware files.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Apparently there are RPi1 devices with BRCM43430 wifi, such as the
Pi Zero W. Add the necessary packages for that to the image generated
for those boards as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch adds a image with squashfs as the root filesystem.
A rootfs_data partition will be generated on the first boot
and placed inside the rootfs partition (just after the squashfs
image).
advantages:
- it is possible to migrate from an existing -ext4
installation and back via sysupgrade.
- existing partition layout will not be lost.
- slightly smaller image size.
- support for attendedsysupgrade
disadvantages:
- needs f2fs + tools as well. This is because fs-tools decides on the
blocksize of the sdcard. So either f2fs or ext4 can get choosen as
the rootfs_data filesystem (depends on the size of the root partition).
- rootfs_data is placed into the rootfs partition. This makes
it difficult for tools that expect a /dev/mmc0pX device.
It also makes it difficult for data recovery tools since they
might not expect to find a embedded partition or will be
confused.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck package into the image... Otherwise the new -squashfs image will
boot of a ram-overlay and won't keep the configurations after a reboot.
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: Paul Spooren <spooren@informatik.uni-leipzig.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 6c2e1ff80f.
GNU gzip does not fail when the image filename already contains the .gz
extension, this is a problem specific to pigz. Revert the commit, as we
now gzip the image twice.
Reported-by: Martin Schleier <drahemmaps@gmx.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The gzip step in the sdcard image build fails because the image filename
already has the gzip extension. This results in an empty image file, to
which the metadata is finally appended.
Remove the .gz extension from the image filename to fix this.
Fixes: e79b096ee1 ("brcm2708: convert to metadata")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.
Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.
Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
64 bit support for Raspberry Pi 3 is experimental. However, bcm2709 subtarget
should serve as a stable and compatible 32 bit support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds support for Raspberry Pi 3 on the bcm2709 subtarget, in order to
keep 32 bit image support when 64 bit support is added on bcm2710 subtarget.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
COPYING is not present in $(LINUX_DIR) on imagebuilder and prevents a
successful image creation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y
Also adds support for Raspberry Pi Compute Module 3 (untested).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This update also adds individual download of firmware files instead of fetching
every file on the repository (10-MiB vs 100+MiB).
Also copy Linux license from kernel directory instead of using the rpi-firmware
one.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make the device name accessible for any build commands instead of
forcing targets to define it themselves.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46597
