Commit Graph

23092 Commits

Author SHA1 Message Date
Sungbo Eo
31697f92a2 ramips: fix MAC address setup for RT5350F-OLinuXino devices
Olimex RT5350F-OLinuXino devices do not have a default MAC address, and there is
nothing at the 0x4 offset in the factory partition. Using a local address, which
is randomly generated by the kernel, would be a better choice.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-19 19:03:07 +08:00
Sungbo Eo
f7112a180f ramips: 5.4: handle ERR_PTR properly
of_get_mac_address can return ERR_PTR since 5.2, so the return pointer should be
checked before used. Otherwise it might cause an oops during boot.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-19 19:03:07 +08:00
INAGAKI Hiroshi
0a05d71f6f ramips: fix initramfs image for I-O DATA mt7621 devices
This is additional fix of c998ae7f0e.

The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-05-19 19:03:07 +08:00
Chuanhong Guo
a43cbfe2e3 ramips: remove default switch setup in 02_network
ramips images now relies on explicit switch setup for proper failsafe
functionality. Remove default cases where it relies on vlan setup in
dts and add switch setup for devices affected.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-05-19 19:03:02 +08:00
Álvaro Fernández Rojas
597df570f3 bcm63xx: reorganize board patches
Let's put some order on board patches.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 11:07:24 +02:00
Álvaro Fernández Rojas
edafbe81e0 bcm63xx: bcm6328-leds: improve HW blinking
Add support for second HW blinking interval.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 11:03:58 +02:00
Álvaro Fernández Rojas
daee6b4661 bcm63xx: add Comtrend VG-8050 support
BCM63169 with 128M RAM, 128M NAND and BCM53125 switch.
Switch is connected by HSSPI to CS5.
More info: https://openwrt.org/toh/comtrend/vg8050

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:47 +02:00
Álvaro Fernández Rojas
62e7342ddf bcm63xx: add NETGEAR DGND3700v2 support
BCM6362 with 64M RAM, 32M NAND and BCM53125 switch.
Switch is connected by MMAP, which is currently unsupported (no VLANs).
More info: https://openwrt.org/toh/netgear/dgnd3700v2

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-19 10:41:42 +02:00
Adrian Schmutzler
74ff0773b5 ramips: remove leading zeros from MAC address location
Cosmetic adjustment to match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
be9eab9bca ramips: set WAN address in DTS for ASUS RT-AC51U/RT-AC54U
The location 0x28 in factory partition is the common one used for
ethernet address on this architecture. Despite, it contains the label
MAC address for the devices at hand.

Consequently, this patch moves 0x28 to the &ethernet node in DTS files
(setting the WAN MAC address there) and sets up the lan_mac from 0x22
in 02_network. As a benefit, this allows to use label-mac-device in
DTS instead of ucidef_set_label_macaddr.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
a1f0fd8cba ramips: use DT trigger for 2G WiFi on ASUS RT-AC51U
Like for the RT-AC54U, this uses a DT trigger for WiFi also at the
RT-AC51U. While at it, rename node and label to wifi2g.

Note that the 5g WiFi LED still isn't supported (see PR #3017 for
further details: https://github.com/openwrt/openwrt/pull/3017 )

Tested-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Adrian Schmutzler
0b34a36da9 ramips: fix MAC address assignment for ASUS RT-AC51U
The current MAC address assignment for the ASUS RT-AC51U is "wrong",
it actually should be the same as for the RT-AC54U. Fix it.

MAC assignment based on vendor firmware:

  2g    0x4	label
  5g    0x8004	label +4
  lan   0x22	label +4
  wan   0x28	label

Thanks to Davide Fioravanti for checking this on his device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 21:51:06 +02:00
Fabian Bläse
33b2078528 mt7621: Make ER-X-SFP factory image compatible with EP-R6
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.

The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.

The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.

This allows the factory image to be flashed on EP-R6 without TFTP.

Signed-off-by: Fabian Bläse <fabian@blaese.de>
2020-05-18 21:11:47 +02:00
David Bauer
4133304413 mpc85xx: restructure image receipts
Move the image receipts into separate per-subtarget files like it is
done on most other targets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-18 21:11:39 +02:00
David Bauer
564f87ef5b mpc85xx: rename generic subtarget to p1010
The mpc85xx-generic subtarget supports the QorIQ SoCs of the p1010
family. Rename the subtarget to reflect this affiliation as it's the
case with the other mpc85xx subtargets.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-18 21:11:22 +02:00
Álvaro Fernández Rojas
367a30389d bcm63xx: add support for Comtrend VR-3032u
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
86583384ff bcm63xx: smp: add NAND support
NAND controller is present on BCM6328, BCM6362, BCM6368 and BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Álvaro Fernández Rojas
cca13d8e82 kernel: mtdsplit: add BCM WFI support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-18 18:24:06 +02:00
Adrian Schmutzler
4a61a88f90 ath79: add support for TP-Link TL-WA901ND v4 and v5
This ports support for the TL-WA901ND v4 and v5 from ar71xx to ath79.
They are similar to the TP9343-based TL-WR940N v3/v4 and TL-WR941ND v6.

Specifications:
  SoC: TP9343
  Flash/RAM: 4/32 MiB
  CPU: 750 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

Flash instruction (TFTP):
  1. Set PC to fixed ip address 192.168.0.66
  2. Download *-factory.bin image and rename it to * (see below)
  3. Start a tftp server with the image file in its root directory
  4. Turn off the router
  5. Press and hold Reset button
  6. Turn on router with the reset button pressed and wait ~15 seconds
  7. Release the reset button and after a short time
     the firmware should be transferred from the tftp server
  8. Wait ~30 second to complete recovery.

  * The image name for TFTP recovery is wa901ndv4_tp_recovery.bin for
  both variants.

In ar71xx, a MAC address with offset 1 was used for ethernet port.
That's probably wrong, but this commit sticks to it until we know
the correct value.

Like in ar71xx, this builds the default factory.bin with EU country
code.

Thanks to Leonardo Weiss for testing on the v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 13:35:38 +02:00
Alexander Couzens
bf5d800578
lantiq: fritz 7360 v2: remove additional supported devices
The additional supported device isn't required since this is a new
device. Some board contains an addtional device,
those device were supported in earlier versions which used the
"old" image builder code.
To support an sysupgrade from such old version, there is the all caps
additional device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:59:22 +02:00
Alexander Couzens
0962baae4e lantiq: fritz 7360 v2: rename device before it will be used
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:57:57 +02:00
Adrian Schmutzler
30cc7f3510 ramips: increase SPI frequency for ASUS RT-AC51U/RT-AC54U
This increases the SPI frequency for both ASUS RT-AC51U and RT-AC54U.

Speed comparison tests have been performed on RT-AC54U:

- 10Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    4m 37.78s
user    0m 0.02s
sys     2m 43.92s

- 50Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 28.34s
user    0m 0.03s
sys     0m 46.96s

- 50Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 11.94s
user    0m 0.01s
sys     0m 46.94s

- 80Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 12.31s
user    0m 0.04s
sys     0m 46.96s

- 80Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real    1m 12.15s
user    0m 0.02s
sys     0m 46.97s

Based on that, we took 50 MHz with fast-read, as higher frequencies
didn't yield further improvements.

For the RT-AC51U, only the final configuration was tested.

Tested-by: Zhijun You <hujy652@gmail.com> [RT-AC54U]
Tested-by: Davide Fioravanti <pantanastyle@gmail.com> [RT-AC51U]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:38:22 +02:00
Álvaro Fernández Rojas
13c33f3f12 bcm63xx: mask interrupts on init
Fixes BCM6348/BCM6358 hangs while booting:
https://bugs.openwrt.org/index.php?do=details&task_id=2202

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-17 23:29:48 +02:00
Roger Pueyo Centelles
a0ef42e77c ath79: add support for Ubiquiti PowerBeam 5AC 500
The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna.

Specifications:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
 - UART: not tested

Not supported:
 - RSSI LEDs (probably through 74HC595 chip)

Installation from stock airOS firmware:
 - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
   https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-05-17 21:03:30 +02:00
Davide Fioravanti
31b49f02ca ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH:   5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615N (4x4:4)
  - 5GHz:   1x MT7615N (4x4:4)
  - 4 antennas: 3 external detachable antennas and 1 internal
USB:
  - 1x USB 3.0
  - 1x USB 2.0
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x White led (Power)
  - 6x Green leds (link lan1-lan4, link wan, wps)
  - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)

Everything works correctly.

Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.

However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).

After this, you should be back in the OEM firmware.

Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).

When the router reboots flash the “factory” OpenWrt image and this
time it should work.

After the OpenWrt installation you have to use the sysupgrade image
for future updates.

Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.

Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
 1) "kernel" and "rootfs"
 2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.

This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.

A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.

Another way to switch the boot partition is:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.

Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.

However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.

If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-17 18:44:28 +02:00
Sungbo Eo
a4e9c8f14b ramips: add support for netis WF2770
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- UART:
  - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-17 18:41:48 +02:00
Zhijun You
46674723e1 ramips: add support for ASUS RT-AC54U
Specification:

- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0

Installation:

   Update using ASUS Firmware Restoration Tool:

1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
   to press and hold the reset button, then turning the router back on while
   keeping the reset button pressed for ~5 secs until the power LED starts
   flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
   Restoration Tool will wrongly assume that the router is not in Rescue Mode
   and will refuse to flash it): go to the Windows Control Panel and
   temporarily disable ALL other network adapters except the one you will use
   to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
   static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
   Ethernet port of the adapter you've just set up) and port 1 of the router
   (not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
   upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
   stays on

MAC assignment based on vendor firmware:

2g    0x4	label
5g    0x8004	label +4
lan   0x22	label +4
wan   0x28	label

Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:40:56 +02:00
Adrian Schmutzler
685cc66c2a ramips: create DTSI for ASUS RT-AC51U and RT-AC54U
This creates a DTSI for the ASUS RT-AC51U and the upcoming RT-AC54U,
as they are quite similar.

White at it, drop the unneeded "status = okay" for ethernet.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:39:48 +02:00
Adrian Schmutzler
b24fd13024 lantiq: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:21 +02:00
Adrian Schmutzler
41b5ca1458 bcm27xx: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
bcm27xx target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Refresh remaining target patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:10 +02:00
Adrian Schmutzler
8ff813e5f4 generic: drop outdated kernel version switches in local drivers
This drops the obsolete version switches for non-supported kernels
from local drivers in generic target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:35:59 +02:00
Adrian Schmutzler
c00b2df6c8 ramips: drop non-existant ralink,port-map for Ravpower WD03
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:34:40 +02:00
Adrian Schmutzler
d7a28e8ed2 ramips: mt7620: tidy up ethernet node in DTS files
This tidies up the ethernet node in mt7620 DTS files by:

- removing unnecessary status as it is not disabled
- reordering properties consistently
- adding empty lines to enhance readability

This should make comparison and reviewing new PRs based on C/P easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:28:03 +02:00
Thibaut VARÈNE
2ea481193c generic: platform/mikrotik: fix LZOR support
31e99fe3da which introduced this code was unfortunately untested.
This commit fixes a number of issues and works around the fact that in
this particular scheme, the LZO payload may be padded at the end which
will trigger a harmless lzo decompression error.
This commit also disambiguates the debug printks.

Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
2020-05-16 20:30:46 +02:00
Yushi Nishida
78bebe680f
lantiq/xrx200: add support for the Fritzbox 7360v2
This commit adds support for the Fritzbox 7360v2

CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A

DECT is not working.

Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.

Firmware can be flashed with this method:

1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
    via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:

passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin

5.) wait till red light flashing turns off.
6.) type: exit

Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.

Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)

Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
2020-05-16 04:37:55 +02:00
Aleksander Jan Bajkowski
2f7118712e ath79: increase spi frequency on tp-link tl-wr1043nd v2
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.

Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.21s
user	0m 0.00s
sys	0m 3.21s

After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.52s
user	0m 0.00s
sys	0m 2.52s

Tested on TP-Link TL-WR1043ND V2.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-05-15 10:00:32 +08:00
Daniel Gonzalez Cabanelas
e04ff3c7cc bcm63xx: periph_intc: report effective affinity
The bcm6345-periph-intc driver only targets a single CPU at a time, even
if the notional affinity is wider. Let's inform the core code about this.

This patch gets rid of the kernel message:
"genirq: irq_chip bcm6345-periph-intc did not update eff. affinity mask
of irq 52"

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2020-05-14 18:10:12 +02:00
Álvaro Fernández Rojas
29c3bb5f41 bcm63xx: ext_intc: fix warning
In file included from ./arch/mips/include/asm/io.h:34,
                 from ./arch/mips/include/asm/mmiowb.h:5,
                 from ./include/linux/spinlock.h:60,
                 from ./include/linux/irq.h:14,
                 from drivers/irqchip/irq-bcm6345-ext.c:10:
drivers/irqchip/irq-bcm6345-ext.c: In function 'bcm6345_ext_intc_of_init':
./arch/mips/include/asm/mach-bcm63xx/ioremap.h:48:9: warning: 'base' may be used uninitialized in this function [-Wmaybe-uninitialized]
  return is_bcm63xx_internal_registers((unsigned long)addr);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-bcm6345-ext.c:255:16: note: 'base' was declared here
  void __iomem *base;
                ^~~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:28:31 +02:00
Álvaro Fernández Rojas
f2f2cf07a6 bcm63xx: periph_intc: fix warning
drivers/irqchip/irq-bcm6345-periph.c: In function 'bcm6345_periph_irq_handle':
drivers/irqchip/irq-bcm6345-periph.c:55:21: warning: 'block' may be used uninitialized in this function [-Wmaybe-uninitialized]
  struct intc_block *block;
                     ^~~~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:27:31 +02:00
Álvaro Fernández Rojas
f314cbe54b bcm63xx: redboot: fix warning
drivers/mtd/parsers/redboot.c: In function 'parse_redboot_partitions':
drivers/mtd/parsers/redboot.c:194:59: warning: suggest parentheses around '-' in operand of '&' [-Wparentheses]
     fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
                                       ~~~~~~~~~~~~~~~~~~~~^~~

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:12 +02:00
Álvaro Fernández Rojas
ee6bf7e865 bcm63xx: bcm6362: fix pinctrl bug
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:12 +02:00
Álvaro Fernández Rojas
aa2f2276f7 bcm63xx: image: remove unused definition
KERNEL_ENTRY isn't used by lzma-loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 16:12:08 +02:00
Álvaro Fernández Rojas
eea23c2004 bcm63xx: remove linux 4.14 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-14 14:52:54 +02:00
Koen Vandeputte
eb17ee294c kernel: bump 5.4 to 5.4.41
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Koen Vandeputte
d503492857 kernel: bump 4.19 to 4.19.123
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-14 13:33:40 +02:00
Adrian Schmutzler
2308644b0c ipq40xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 19:16:41 +02:00
Adrian Schmutzler
fdd968d64e bcm63xx: replace "ok" with "okay" for status in DTS files
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 16:59:04 +02:00
Adrian Schmutzler
026fe1308c bcm63xx: use generic diag.sh
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.

Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.

For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-12 16:57:45 +02:00
Thibaut VARÈNE
96414047c9 ar71xx: mikrotik: mach-rbspi.c remove wlan id
Following on the previous commit, this patch removes useless id argument
from rbspi_wlan_init().

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:41:12 +02:00
Thibaut VARÈNE
1c6990fe6d ar71xx: mikrotik: bypass id check in __rb_get_wlan_data()
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.

Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.

Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-12 12:41:08 +02:00
Koen Vandeputte
0fed36dd48 kernel: bump 5.4 to 5.4.40
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Koen Vandeputte
7dd2d7289a kernel: bump 4.19 to 4.19.122
Refreshed all patches.

Remove upstreamed:
- 551-loop-Better-discard-support-for-block-devices.patch

Fixed:
- CVE-2020-11884
- CVE-2020-12114
- CVE-2019-3016
- CVE-2020-11669

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Koen Vandeputte
ef2d5a2ab4 kernel: bump 4.14 to 4.14.180
Refreshed all patches.

Fixes:
- CVE-2020-12114
- CVE-2020-11669

Compile-tested on: pistachio
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-12 12:36:28 +02:00
Álvaro Fernández Rojas
a0081b1945 bcm63xx: loader-lzma: use default lzma
Specific CFE LZMA parameters aren't needed for LZMA Loader.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Álvaro Fernández Rojas
84646936a6 bcm63xx: image: rename LOADADDR to KERNEL_LOADADDR
Also remove KERNEL_ENTRY, since it's the same as KERNEL_LOADADDR

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-05-12 12:34:57 +02:00
Koen Vandeputte
146e18af56 generic: add MikroTik hw bit description
An e-mail response from MikroTik contained a minimal overview
on hardware option bits which mentioned a currently unknown bit.

While not being too detailed what it does, add it for documentation purposes.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-11 16:49:04 +02:00
David Bauer
300b7fe85a ipq40xx: add support for Aruba AP-365
Hardware
--------
SoC:   Qualcomm IPQ4029
RAM:   512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
       - 4MB SPI-NOR (Macronix MX25R3235F)
TPM:   Atmel AT97SC3203
BLE:   Texas Instruments CC2540T
       attached to ttyMSM0
ETH:   Atheros AR8035
LED:   System (red / green / amber)
BTN:   Reset

The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.

Console baudrate is 9600 8n1.

To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.

Installation
------------

1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
   into the TFTP server root directory. Configure the TFTP server to
   be reachable at 192.168.1.75/24. Connect the machine running the TFTP
   server to the ethernet port of the access point.

2. Connect to the serial console. Interrupt autobooting by pressing
   Enter when prompted.

3. Configure the bootargs and bootcmd for OpenWrt.
   $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
   $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
     ubi read 0x85000000 kernel; bootm 0x85000000"
   $ setenv ramboot_openwrt "run bootargs_openwrt;
     setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
     netget; set fdt_high 0x87000000; bootm"
   $ setenv bootcmd "run nandboot_openwrt"
   $ saveenv

4. Load OpenWrt into RAM:
   $ run ramboot_openwrt

5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
   /tmp folder on the device.

6. Flash OpenWrt:
   Make sure you use the mtd partition with the label "ubi" here!

   $ ubidetach -p /dev/mtd1
   $ ubiformat /dev/mtd1
   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:

  $ setenv bootcmd "boot"
  $ saveenv

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-05-11 01:05:16 +02:00
Andrey Kunitsyn
e31e5c4ea4 bcm27xx: label to boot partition
Get fat partition name allow easy partition identification
for user.

Signed-off-by: Andrey Kunitsyn <blackicebox@gmail.com>
2020-05-10 17:06:27 +02:00
Pawel Dembicki
426fb8cf84 ramips: add support for LB-Link BL-W1200
The BL-W1200 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader

Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.

Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.

How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin

Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-05-09 20:02:17 +02:00
Sungbo Eo
0cdf7bc4fb ramips: dts: fix incorrect flash reg property
Most work was done in commit 021c893658 ("ramips: fix size-cells on spi
nodes"), but a few more DTS files using the old reg style have been added
since then. This commit fixes them.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-09 14:49:33 +02:00
Sungbo Eo
1eceab3fc0 ramips: dts: use generic node name for flash
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

While at it, remove unused m25p80 label.

Tested on rt5350 (for spi-nor) and rt3662 (for cfi-flash).

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-09 14:48:50 +02:00
Jakov Petrina
b1cfbff0a7 mvebu: uDPU: switch default kernel and U-Boot PHY mode
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.

However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.

Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2020-05-09 14:34:23 +02:00
Lech Perczak
94f3449977 ath79: dts: add missing 'serial0' alias for TP-Link TL-MR3040v2
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2020-05-08 19:39:36 +02:00
Sungbo Eo
a5720d3276 ramips: tidy up image subtarget Makefiles
- use tab indent in image build recipes for consistency
- harmonize line wrapping

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-08 18:58:39 +02:00
Sungbo Eo
c5fdab84ed ramips: tidy up image Makefile
- sort recipes alphabetically
- simplify subtarget include directives

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:53:23 +02:00
Sungbo Eo
fa9e7ca466 ramips: simplify palmbus/{i2c,spi} in device DTS files
As the node is already defined and labeled in SoC DTSI file, we can refer to it
outside of root node and reduce redundancy.

While at it, remove unused pcf8563 label.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:43:00 +02:00
Sungbo Eo
22a21b0c18 ramips: use hex notation for *-mtd-eeprom property
Change "0" to "0x0" for consistency. This is an extension of commit 34abfb6e91
("ramips: convert mediatek,mtd-eeprom from decimal to hex notation").

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:34:27 +02:00
Koen Vandeputte
51a7184a7d generic: fix patching error on kernel 5.4
Fixes a build error seen when applying the kernel patches.

Applying patch generic/435-mtd-add-routerbootpart-parser-config.patch
patching file drivers/mtd/parsers/Kconfig
Hunk #1 FAILED at 160.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Kconfig
patching file drivers/mtd/parsers/Makefile
Hunk #1 FAILED at 10.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Makefile

This was missed as 5.4 is currently set as testing kernel
while the main kernel being used is 4.19

Fixes: 2976e423dc ("generic: routerboot partition build bits")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-05-08 17:06:10 +02:00
Thibaut VARÈNE
5e50515fa6 ramips/mt7621: mikrotik: don't use mtd-mac-address in DTS
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.

Adjust config so that WAN is base MAC and LAN is base MAC +1 to better
match label and vendor OS.

[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:18 +02:00
Thibaut VARÈNE
9242d691ec ath79/mikrotik: load caldata via sysfs loader
This commit takes advantages of base-files 220 which introduces routines
to perform caldata loading directly via the kernel sysfs loader helper.
This has the benefits of not wasting flash space to store caldata.

Memory footprint is reduced to the bare minimum: for devices that don't
need MAC patching, the caldata is loaded directly, for devices that do
need MAC patching, the caldata is extracted to /tmp, patched and then
loaded.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
e995577e70 ar71xx/mikrotik: ath10k: use new sysfs driver
Fetch ath10k calibration data from new mikrotik sysfs driver

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
1e24af5638 ath79/mikrotik: use standard caldata functions
With the implementation of a sysfs interface to access WLAN data, this
target no longer needs a special wrapper to extract caldata.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
301bc3290d ath79/mikrotik: don't use mtd-mac-address in DTS
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.

To match sticker and vendor OS behavior, WAN MAC is set to the device
base MAC and LAN MAC is incremented from that.

Note: this will trigger a harmless kernel message during boot:
ag71xx 19000000.eth: invalid MAC address, using random address

There is no clean workaround to prevent this message from being emitted.

[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
31e99fe3da generic: platform/mikrotik: support LZOR encoding
Some newer MikroTik RouterBOARD devices use a new encoding scheme
for their WLAN calibration data. This patch provides support for
decoding this new scheme.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
97337d3e5d ramips/mt7621: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
00d2ab7602 ar71xx/mikrotik: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
65d5053045 ath79/mikrotik: enable mikrotik platform driver
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
1dcc2249cd generic: mikrotik platform build bits
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
5ecf7d9654 generic: routerboot sysfs platform driver
This driver exposes the data encoded in the "hard_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "hard_config". The WLAN calibration data is available on demand via
the 'wlan_data' sysfs file in that folder.

This driver permanently allocates a chunk of RAM as large as the
"hard_config" MTD partition (typically 4KB), although it is technically
possible to operate entirely from the MTD device without using a local
buffer (except when requesting WLAN calibration data), at the cost of a
performance penalty.

This driver does not reuse any of the existing code previously found in
routerboot.c.

This driver has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
21869e8f80 ramips: mikrotik: use routerbootpart partitions
Enable routerbootpart partitions on MikroTik devices.

Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
274221a836 ramips/mt7621: enable CONFIG_MTD_ROUTERBOOT_PARTS
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
8f90dbfd1f ath79/mikrotik: use routerbootpart partitions
Enable routerbootpart partitions on MikroTik devices.

Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
c8b2ad4185 ath79/mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
2976e423dc generic: routerboot partition build bits
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Thibaut VARÈNE
ee5ee99dcf generic: routerbootpart MTD parser for RouterBoot
This driver provides an OF MTD parser to properly assign the RouterBoot
partitions on the flash. This parser builds from the "fixed-partitions"
one (see ofpart.c), but it can handle dynamic partitions as found on
routerboot devices.

The parent node must contain the following:
	compatible = "mikrotik,routerboot-partitions";
	#address-cells = <1>;
	#size-cells = <1>;

Children routerbootpart DTS nodes are defined as follows:
For fixed partitions
	node-name@unit-address {
		reg = <prop-encoded-array>;
		label = <string>;
		read-only;
		lock;
	};

All properties but reg are optional.

For dynamic partitions:
	node-name {
		size = <prop-encoded-array>;
		label = <string>;
		read-only;
		lock;
	};

size property is mandatory unless the next partition is a fixed one or
a "well-known" one (matched from the strings defined below) in which case
it can be omitted or set to 0; other properties are optional.

By default dynamic partitions are appended after the preceding one, except
for "well-known" ones which are automatically located on flash.

Well-known partitions (matched via label or node-name):
 - "hard_config"
 - "soft_config"
 - "dtb_config"

This parser requires the DTS to list partitions in ascending order as
expected on the MTD device.

This parser has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.

Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-08 15:17:17 +02:00
Stijn Tintel
03fd38d612 kernel: add missing symbol to 5.4 config
This symbol is exposed if KERNEL_PROVE_LOCKING is enabled.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-05-08 05:56:36 +03:00
Rosen Penev
73fa1aba94 samba36: Remove
Samba 3.6 is completely unsupported, in addition to having tons of patches

It also causes kernel panics on some platforms when sendfile is enabled.
Example:

https://github.com/gnubee-git/GnuBee_Docs/issues/45

I have reproduced on ramips as well as mvebu in the past.

Samba 4 is an alternative available in the packages repo.

cifsd is a lightweight alternative available in the packages repo. It is
also a faster alternative to both Samba versions (lower CPU usage). It
was renamed to ksmbd.

To summarize, here are the alternatives:
- ksmbd + luci-app-cifsd
- samba4 + luci-app-samba4

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[drop samba36-server from GEMINI_NAS_PACKAGES, ksmbd rename + summary]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-05-08 03:32:52 +03:00
Yangbo Lu
70a6a98149 layerscape: define only one package for ls-dpl
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-dpl with only one package
installing all 4 files as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
2e61c4ac1f layerscape: define only one package for ls-mc
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-mc with only one package
installing all two images as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
6c9d8990a4 layerscape: define only one package for fman-ucode
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain fman-ucode with only one package
installing all two binaries as intermediate files.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
084c82c5b0 layerscape: define only one package for ls-rcw
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
e12ec82e44 layerscape: switch to kernel 5.4
Switch to kernel 5.4 in Makefile.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
670684d9d4 layerscape: disable UEFI runtime support in config-5.4
Disable CONFIG_EFI (UEFI runtime support) in config-5.4,
while is not required.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
7a08169dc1 layerscape: re-enable IFC NAND/NOR controllers in config-5.4
The Freescale IFC NAND/NOR controllers options were disabled
in default in previous running make kernel_oldconfig.
So re-enable them.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
f3476e5be6 layerscape: refresh kernel 5.4 config
By running make kernel_oldconfig and selecting relevant options.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
a812ebafa1 layerscape: copy kernel config from 4.14 to 5.4
Just copy kernel config from 4.14 to 5.4.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
cddd459140 layerscape: add patches-5.4
Add patches for linux-5.4. The patches are from NXP LSDK-20.04 release
which was tagged LSDK-20.04-V5.4.
https://source.codeaurora.org/external/qoriq/qoriq-components/linux/

For boards LS1021A-IOT, and Traverse-LS1043 which are not involved in
LSDK, port the dts patches from 4.14.

The patches are sorted into the following categories:
  301-arch-xxxx
  302-dts-xxxx
  303-core-xxxx
  701-net-xxxx
  801-audio-xxxx
  802-can-xxxx
  803-clock-xxxx
  804-crypto-xxxx
  805-display-xxxx
  806-dma-xxxx
  807-gpio-xxxx
  808-i2c-xxxx
  809-jailhouse-xxxx
  810-keys-xxxx
  811-kvm-xxxx
  812-pcie-xxxx
  813-pm-xxxx
  814-qe-xxxx
  815-sata-xxxx
  816-sdhc-xxxx
  817-spi-xxxx
  818-thermal-xxxx
  819-uart-xxxx
  820-usb-xxxx
  821-vfio-xxxx

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Petr Štetiar
d1d2c0b557 kernel: bump 5.4 to 5.4.39
Refreshed patches.

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53, layerscape/armv7+armv8_64b

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-07 12:53:06 +02:00
Chuanhong Guo
47f17b0662 generic: ar8216: fix unknown packet flooding for ar8229/ar8236
ar8229 and ar8236 don't allow unknown unicast/multicast frames and
broadcast frames to be flooded to cpu port. This isn't desired behavior
for swconfig as we treat it as a standalone switch.
Current code doesn't enable unicast frame flooding for ar8229 and uses
wrong setup for ar8236. This commit fixes both of them by enabling port
0 flooding for all unknown frames.

Fixes: FS#2848
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-05-06 08:59:27 +08:00
Adrian Schmutzler
0fb5962e62 sunxi: remove unneeded shebang for preinit files
preinit files are sourced and they have no execute bit set, so remove
their shebang.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-05 13:09:19 +02:00
Adrian Schmutzler
755790808c sunxi: tidy up cases in base-files
This removes unnecessary quotes in cases and applies alphabetic
order to members.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-05 13:06:26 +02:00
Petr Štetiar
73de205c57 kernel: bump 5.4 to 5.4.38
Refreshed patches.

Run tested: qemu-x86-64, apalis
Build tested: x86/64, ipq40xx, ath79, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-04 21:09:12 +02:00
John Crispin
220f43e0f2 mediatek: fix image building
Signed-off-by: John Crispin <john@phrozen.org>
2020-05-04 16:28:46 +02:00
John Crispin
abb0452cd8 mediatek: update patches
Signed-off-by: John Crispin <john@phrozen.org>
2020-05-04 16:27:30 +02:00
Stijn Tintel
49ab97ca86 bcm27xx: backup /boot/cmdline.txt and restore early
If you want to use the Raspberry Pi UART, "console=serial0,115200" needs
to be removed from the kernel cmdline. This is done by editing
/boot/cmdline.txt. However, this file is not currently backed up during
sysupgrade, so this effectively breaks HATs that require the use of the
UART every sysupgrade.

Backup this file during sysupgrade, and restore it before rebooting.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-05-03 17:30:45 +03:00
Petr Štetiar
5ea3ea154f kernel: bump 5.4 to 5.4.36
Refreshed patches, removed upstreamed patch:

 generic/hack: 551-loop-Better-discard-support-for-block-devices.patch

Added generic config symbol `ARM64_ERRATUM_1542419` due to Fixes:
f2791551cedb ("arm64: errata: Hide CTR_EL0.DIC on systems affected by
Neoverse-N1 #1542419").

Run tested: qemu-x86-64, apalis, nbg6617
Build tested: x86/64, imx6, ipq40xx, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-30 00:52:04 +02:00
Daniel Golle
aa0526b5f2 ath79: fix dts of Teltonika RUT9xx devices
The previous commits were missing a semicolon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 22:59:23 +01:00
Daniel Golle
aa4a33ac62 ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.

To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Daniel Golle
c8b309b53d ath79: split Teltonika RUT955 to support other RUT9xx models
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 21:32:35 +01:00
Adrian Schmutzler
d9ff499671 kirkwood: disable image for Linksys EA3500 (Audi)
Due to the switch to DSA, the kernel image has become too big (2641k) for the
kernel partition (2624k) on this device:

  WARNING: Image file [...]/linux-kirkwood/linksys_audi-uImage is too big

Disable the device until this is fixed, so buildbots can continue their work.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-29 18:04:16 +02:00
Adrian Schmutzler
522f6b7eee ath79: add SUPPORTED_DEVICES based on ar71xx for some devices
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.

Fixes: FS#3017

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 20:28:06 +02:00
Adrian Schmutzler
03e742dcd8 Revert "ramips: explicitly disable built-in switch for lan-only devices"
This reverts commit a1693bf626.

The rt288x and rt3883 devices in question don't have switches.
Only keep the merged case for rt305x.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 16:53:29 +02:00
Adrian Schmutzler
8b373892d3 kirkwood: remove support for kernel 4.19
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices, while support for 4.19 has never left testing state.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-28 16:50:20 +02:00
Adrian Schmutzler
0af2c44604 kirkwood: remove support for kernel 4.14
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-28 16:49:31 +02:00
Pawel Dembicki
4fd7e539e4 kirkwood: switch from swconfig to dsa
This patch removes support for swconfig and switches to dsa driver.

swconfig and switch drivers are removed. DSA driver is enabled and
configuration is adjusted.

In kirkwood only two devices have switches: Linksys EA3500 and EA4500.

WAN MAC configuration in 02_network is required because otherwise WAN
would have the same MAC address as lan interfaces. In swconfig solution
the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled
and wan is part of the switch, we have to set it manually.

Compile tested: EA3500, EA4500
Run tested: EA4500

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[minor commit title/message adjustments, remove swconfig package
for devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 16:49:31 +02:00
DENG Qingfang
a10537f674 ramips: fix MikroTik 750Gr3 ports MAC addresses
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.

Fix the MAC addresses in OpenWrt.

Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 10:57:17 +02:00
Álvaro Fernández Rojas
2e5e9b459e ath10k-ct-firmware: rename ct-htt packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-28 09:33:09 +02:00
Andre Heider
87c909e969 omap: remove support for kernel 4.14
There's support for 5.4 and 4.19 now, remove the 3rd option.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-04-28 01:10:48 +02:00
Andre Heider
1e3ee247be omap: switch to kernel 5.4
Runtime tested on beagleblack.

Signed-off-by: Andre Heider <a.heider@gmail.com>
[added test comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-28 01:10:42 +02:00
Andre Heider
d20cfa2bd3 omap: make kernel_oldconfig
Attempt to keep the same nand/sound/panel functionality using new knobs.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-04-28 01:10:37 +02:00
Andre Heider
75f7f7eee9 omap: copy kernel 4.19 config for 5.4
Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-04-28 01:10:33 +02:00
Adrian Schmutzler
80a094aaf3 ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation AC
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:28:51 +02:00
Roger Pueyo Centelles
e210fe91b1 ath79: add support for Ubiquiti PowerBeam 5AC Gen2
The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.

Specifications:
 - SoC: Qualcomm Atheros AR9342 rev 2
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR (mx25l12805d)
 - Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
 - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
 - WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
 - UART: not tested

Installation from stock airOS firmware:
 - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:17:30 +02:00
Adrian Schmutzler
f0435d5343 ramips: rt3883: remove swconfig from individual DEVICE_PACKAGES
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.

Remove the redundant inclusions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:07:49 +02:00
Adrian Schmutzler
40325abe52 ramips: remove (kmod-)swconfig DEVICE_PACKAGES for Sitecom WL-351
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:59:40 +02:00
Sungbo Eo
a1693bf626 ramips: explicitly disable built-in switch for lan-only devices
Commit 8f6334eb94 ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.

While at it, consolidate duplicate cases in interface setup.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-27 22:54:51 +02:00
Adrian Schmutzler
1553f58a98 ramips: create common definition for I-O DATA NAND devices
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:37:23 +02:00
Yong-hyu, Ban
8fdf77878f mediatek: fix compile error caused by upstreamed mtk_m32 function
This fixes following compile error:

```
  CC      drivers/net/ethernet/mediatek/mtk_eth_soc.o
drivers/net/ethernet/mediatek/mtk_eth_soc.c:70:5: error: conflicting types for 'mtk_m32'
 u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
     ^~~~~~~
In file included from drivers/net/ethernet/mediatek/mtk_eth_soc.c:25:
drivers/net/ethernet/mediatek/mtk_eth_soc.h:964:6: note: previous declaration of 'mtk_m32' was here
 void mtk_m32(struct mtk_eth *eth, u32 clear, u32 set, unsigned reg);
      ^~~~~~~
```

which caused by 5.4.34 mainlining of mtk_m32 function.

Fixes: faf668be35 ("kernel: bump 5.4 to 5.4.34")
Signed-off-by: Yong-hyu, Ban <perillamint@quendi.moe>
2020-04-27 22:32:07 +02:00
INAGAKI Hiroshi
c998ae7f0e ramips: use lzma-loader for I-O DATA mt7621 devices
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Note:
  These devices use Z-LOADER to read the kernel from NAND flash and boot
  it. Z-LOADER cannot load and start plain lzma-loader, so additional
  lzma-compression is needed.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-04-27 12:22:02 +02:00
INAGAKI Hiroshi
a25bb8610f ramips: use lzma-loader for Japanese mt7621 devices
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-27 12:22:02 +02:00
Szabolcs Hubai
ce19571004 ramips: mt7621: use lzma-loader for D-Link DIR-860L B1
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.

Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.

Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB

To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.

The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!

[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
654eec5a2d ath79: enable SGMII workaround for affected boards
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
David Bauer
c760469918 ath79: ag71xx: unify version dependent code
Use IS_ERR_OR_NULL macro to use the same code on kernel 4.19 as well as
5.4.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:21:45 +02:00
David Bauer
5358d8b995 ath79: ag71xx: remove code for legacy kernels
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
David Bauer
3f5997fb28 ath79: remove unused TP-Link partition parser
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:20:41 +02:00
Adrian Schmutzler
3fdb08681b mvebu: tidy up support for GL.iNet GL-MV1000
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:

- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 00:25:12 +02:00
DENG Qingfang
ad697aabc3 bcm53xx: 5.4: enable NAND
NAND driver was dropped in the 5.4 bump, so enable it back

Fixes: 50c6938b95 ("bcm53xx: add v5.4 support")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-26 21:45:41 +02:00
Li Zhang
050c24f05c mvebu: add support for GL.iNet GL-MV1000
This patch adds supports for GL-MV1000.

Specification:
	- SOC: Marvell Armada 88F3720 (1GHz)
	- Flash: 16MB (W25Q128FWSIG)
	- RAM: 1GB DDR4
	- Ethernet: 3x GE (1 WAN + 2 LAN)
	- EMMC: 8GB EMMC (KLM8G1GETF-B041)
	- MicroSD: 1x microSD slot
	- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
	- Button: 1x reset button,1x slide switch
	- LED: 3x greed LED
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)

	Update firmware instructions
	============================
	In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[Copied dts file to files-5.4]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-26 21:45:41 +02:00
Matt Merhar
ee500186a5 kernel: backport fix for non-regular inodes on f2fs
Upstream commit dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").

On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.

More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2020-04-26 21:45:41 +02:00
Sungbo Eo
1dedad2a00 ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:13:33 +02:00
Sungbo Eo
d16a486766 ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.

Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:10:24 +02:00
Sungbo Eo
01961f163d oxnas: move service file to correct place
This service file has been misplaced from the very beginning.

Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:05:15 +02:00
Petr Štetiar
97d86426e2 x86: fix unusable squashfs images by adding missing padding
It was reported, that after image generation rework
x86-64-generic-squashfs-rootfs.img image won't boot on XenServer x86_64
anymore:

 F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x84289960)
 F2FS-fs (xvda): Can't find valid F2FS filesystem in 1th superblock
 F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x4e8ee223)
 F2FS-fs (xvda): Can't find valid F2FS filesystem in 2th superblock
 List of all partitions:
 ca00            4207 xvda
  driver: vbd
 No filesystem could mount root, tried:
  ext3
  ext2
  ext4
  squashfs
  iso9660
  f2fs

 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(202,0)

So lets fix this by adding back padding which was introduced in commit
a17d9482f5 ("x86: image: fix small disk space in squashfs overlay").

Ref: FS#3036
Fixes: 258f070d1a ("x86: fix missing squashfs and ext4 rootfs images")
Fixes: cb007a7bf6 ("x86: switch image generation to new code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-26 12:53:27 +02:00
René van Dorst
4c70bb4f90
ramips: enable SFP port for Ubiquiti ER-X-SFP
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.

Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.

With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.

NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:48:45 +02:00
René van Dorst
ec2f7a47d3 kernel: add module to support SFP cages
Enables kernel SFP case support.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
DENG Qingfang
6d924706a6 ramips: phy: at803x: support RGMII-to-SerDes and SFP support
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
DENG Qingfang
63696bd0fb kernel: backport support for clause 37 1000Base-X auto-negotiation
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
Petr Štetiar
ef5d37ba5e kernel: bump 5.4 to 5.4.35
Refreshed one patch.

Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53, rockchip/armv8

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-25 13:22:28 +02:00
Petr Štetiar
4a3e0f736f imx6: add back perf monitor related config symbol
Commit 0543eb1110 ("imx6: 5.4: add missing kernel perf monitor
symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which
is exposed only when building perf, so add it back.

Fixes: 8d9b36270b ("imx6: refresh kernel config")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-25 13:22:28 +02:00
David Bauer
9fac9168c6 ipq40xx: fix alphabetical order in 02_network
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:41 +02:00
David Bauer
1f45ed6c99 ath79: fix QCA953x DDR and GPIO compatible bindings
The memory as well as GPIO controller had the wrong SoC name used for
their compatible binding.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:18 +02:00
David Bauer
fceef288cf ath79: correct QCA9550 machine compatible binding
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:03:00 +02:00
David Bauer
c0a80b7125 ath79: rename qca9557.dtsi to qca955x.dtsi
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.

Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-24 20:02:29 +02:00
Adrian Schmutzler
d3c9630811 ath79: move tplinkpart.c parser to patches
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.

While at it, remove some outdated kernel version switches from
the C code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:59 +02:00
Adrian Schmutzler
5f92349841 kernel: fix include of myloader.o since kernel 5.4
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.

This resulted in linking errors like the following (on ath25@5.4):

make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
   needed by 'drivers/mtd/parsers/built-in.a'.  Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2

Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.

Other patches have been refreshed accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-24 17:50:12 +02:00
Adrian Schmutzler
58bec0d172 ramips: remove config-4.14 for mt7621/mt76x8
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their
DTS(I) files are incompatible to kernel 4.14.

Remove the corresponding kernel config files to signal that more
boldly and to prevent accidentally patching the wrong kernel when
pulling in older config patches.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:39:48 +02:00
Adrian Schmutzler
f6573ec24e octeon: use kernel version 5.4 for testing
Tested on EdgeRouter Lite (by Daniel Engberg)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:54 +02:00
Daniel Engberg
2095a4e276 octeon: update config for kernel 5.4
Update config with make kernel_oldconfig.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, redo kernel_oldconfig, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:32 +02:00
Daniel Engberg
655c14e88c octeon: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, refresh on newer kernel, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:26 +02:00
Daniel Engberg
91594cb137 octeon: copy files to kernel 5.4
Copy config and patches to kernel 5.4.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, fix patches-5.4 dirname, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-23 18:38:19 +02:00
Felix Fietkau
df27e949fb mediatek: disable the unused pcie port for elecom wrc-2533gent
Fixes MSI support for the primary device

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-04-22 10:50:15 +02:00
Petr Štetiar
faf668be35 kernel: bump 5.4 to 5.4.34
Refreshed patches.

Run tested: qemu-x86-64, apalis, a64-olinuxino
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-21 22:16:33 +02:00
Koen Vandeputte
8d9b36270b imx6: refresh kernel config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-21 14:46:52 +02:00
Alexander Couzens
36f628910b lantiq/fritz 7312: set maximum speed to 100 mbit
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-04-21 00:01:49 +02:00
Daniel Golle
be6543c539 x86: really remove packages already enabled in kconfig
This commit really removes packages in geode profiles already enabled
in kernel config.

Fixes: 9c23ecee57 ("x86: move packages selection to profiles")
Reported-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-20 19:24:18 +01:00
Tomasz Maciej Nowak
9c23ecee57 x86: move packages selection to profiles
This can be rather confusing for contributors, since there are three
layers in which they can be added. As for now there are none profiles
other than generic (exception: geos) let's move them to these profiles.
Being here this commit also removes packages in geode profiles already
enabled in kernel config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
eca6946447 x86: select kmod-button-hotplug by default
This package is useful by all subtargets, therefore move it to default
packages selection.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
fd94d03ae6 x86: fix kmod-forcedeth package selection
There's no such package as forcedeth, threfore the driver is never
selected. Fix it by properly specifying package name.

Fixes: 35f208d ("x86: add nforce eth to default packages")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tomasz Maciej Nowak
282e7862b7 x86: image: drop dead code
These are remnants of old image generation code, which now serve no
purpose.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-20 18:55:30 +01:00
Tobias Mädel
6a05a85dcb rockchip: add support for Pine64 RockPro64
This adds the new rockchip target and support for RockPro64 RK3399

Flash:    16 MiB SPI NOR
RAM:      2 GiB/4 GiB LPDDR4
SoC:      RK3399
USB:      2x USB 2.0, 1x USB 3.0, 1x USB-C
Ethernet: 1x GbE
PCIe:     PCIe 2.0, 4 lanes
Storage:  eMMC or SD card
Optional SDIO wifi/bt module

The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector,
6 ARM64 cores (4 little, 2 big), plenty of RAM and storage.

By default the single Gigabit-Ethernet port is configured as the
LAN port.

Installation of the firware is possible by dd'ing the image
to an SD card or the eMMC flash.

Serial: 3v3 1500000 8n1

U-boot is build from the mainline tree and
integrated into the images. Required ATF to build u-boot
is downloaded from a CI build bot.

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-20 16:37:56 +02:00
Pawel Dembicki
08f5cac6fb ramips: mt7621: add NETGEAR R7200 as DEVICE_ALT1
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")

Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 11:13:39 +01:00
David Bauer
8d9c1087e4 ath79: add support for AVM FRITZ!WLAN Repeater 450E
SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the device afterwards to boot OpenWRT.

Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-19 16:45:40 +02:00
Sungbo Eo
45e2b7763f ramips: replace pinctrl property names for ipTIME A1004ns
The pinctrl driver had been replaced with the upstream one in b756ea2a90
("ramips: replace pinctrl property names"), but the initial A1004ns support
patch did not reflect the changes. This commit updates its pinctrl property
names.

Fixes: 9169482f64 ("ramips: add support for ipTIME A1004ns")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-19 13:47:23 +08:00
Álvaro Fernández Rojas
d27e2c67ed bcm63xx: switch to 5.4 kernel
Seems stable after 6 days of testing on some of my devices.
Let's switch to 5.4 in order to get more feedback.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-04-18 20:58:38 +02:00
Chuanhong Guo
19d9db5a96 ramips: mt7621: use lzma-loader for newifi d1/d2/thunder timecloud
These devices failed to properly extract kernel. enable lzma loader
for them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 14:19:38 +08:00
Chuanhong Guo
1e5d014ba2 ramips: don't reuse KERNEL_DTB for lzma-loader
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:40:31 +08:00
Chuanhong Guo
51c6b14092 ramips: mt7621: backport more pcie driver fixes
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:06:48 +08:00
Sungbo Eo
13a185bf8a ramips: increase spi-max-frequency for ipTIME mt7620 devices
This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz.

[    5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226
[    5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162

`time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns,
and from 11.39s to 8.81s on A1004ns.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
Sungbo Eo
9169482f64 ramips: add support for ipTIME A1004ns
ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
René van Dorst
d682dcc939 ramips: mt7621: Ubiquiti ER-X-SFP: fix gpio numbers for POE enable gpios
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-18 11:59:41 +08:00
René van Dorst
2fac1322f7 ramips: mt7621: Ubiquiti ER-X: fix gpio number for POE enable gpio
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-18 11:59:41 +08:00
DENG Qingfang
d74fb0088c ramips: use all reserved space for HiWiFi HC5962
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:52:12 +08:00
DENG Qingfang
7dc82528a2 ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation

Recovery to stock instruction:
1. Download stock firmware at
   http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware

Then repeat the instruction in edae3479e6 to install OpenWrt

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:50:57 +08:00
Mantas Pucka
4745969ad7 generic: spi-nor: fix 4-byte opcode support for w25q256
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.

Fixes broken reboot on 8devices Habanero since f0f35fdac

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2020-04-18 11:37:06 +08:00
Petr Štetiar
23916bca61 kernel: bump 5.4 to 5.4.33
Refreshed patches, removed upstreamed patches:

 oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
 oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 15:18:12 +02:00
David Bauer
edf812e25c ath79: remove stray pipe
Fixes: 8918c038f3 ("ath79: add support for AVM FRITZ!WLAN Repeater 1750E")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 14:15:09 +02:00
David Bauer
8918c038f3 ath79: add support for AVM FRITZ!WLAN Repeater 1750E
This commit adds support for the AVM Fritz!WLAN Repeater 1750E

SOC:	Qualcomm QCA9556 (Scorpion) 720MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
WLAN2:  QCA9880 5 GHz 802.11 n/ac 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (correct MAC)
 - 5 GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:27:40 +02:00
David Bauer
d883eaacd4 ath79: add QCA9550 reset sequence
The QCA9550 family of SoCs have a slightly different reset
sequence compared to older chips.

Normally the bootloader performs this sequence, however
some bootloader implementation expect the operating system
to clear the reset. Also get the PCIe resets from OF to
support the second RC of the QCA9558.

This is required for the AVM FRITZ!WLAN Repeater 1750E to work,
as EVA leaves the PCIe bus in reset.

Tested: AVM FRITZ!WLAN Repeater 1750E - OCEDO Koala

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-17 13:23:06 +02:00
Koen Vandeputte
75ef28be59 kernel: add support for GD25D05 SPI NOR (5.4)
This chip is used on newer RB912UAG-5HPnD r2 and 922UAGS-5HPacD boards:

Before:

[    0.824562] spi-nor spi0.0: unrecognized JEDEC id bytes: c8 40 10 c8 40 10
[    0.831607] spi-nor: probe of spi0.0 failed with error -2

After:

[    0.825347] spi-nor spi0.0: gd25d05 (64 Kbytes)
[    0.830291] 1 routerbootpart partitions found on MTD device spi0.0
[    0.836577] Creating 1 MTD partitions on "spi0.0":
[    0.841448] 0x000000000000-0x000000010000 : "partitions"
[    0.848418] 4 routerbootpart partitions found on MTD device partitions
[    0.855092] Creating 4 MTD partitions on "partitions":
[    0.860318] 0x000000000000-0x00000000c000 : "routerboot"
[    0.866548] 0x00000000c000-0x00000000d000 : "hard_config"
[    0.872832] 0x00000000d000-0x00000000e000 : "bios"
[    0.878580] 0x00000000e000-0x00000000f000 : "soft_config"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 14:36:35 +02:00
Roger Pueyo Centelles
c0430b8da4 ath79: reduce spi-max-frequency for Mikrotik wAP G-5HacT2HnD
The previous spi-max-frequency value did not work with all the CPU speed
settings (configurable with rbcfg or from the stock firmware); the new
one does for the three of them.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-04-16 13:44:18 +02:00
Koen Vandeputte
20efd5614a ath79: MikroTik: fix missing nand on kernel 5.4
Following symbol got renamed upstream:
CONFIG_MTD_NAND --> CONFIG_MTD_RAW_NAND

Also add this renamed symbol so NAND also works on kernel 5.4.

After:
[    0.628372] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.634862] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.639554] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.647263] Scanning device for bad blocks
[    0.656228] random: fast init done
[    0.789652] 3 fixed-partitions partitions found on MTD device ar934x-nand
[    0.796550] Creating 3 MTD partitions on "ar934x-nand":
[    0.801874] 0x000000000000-0x000000040000 : "booter"
[    0.807715] 0x000000040000-0x000000400000 : "kernel"
[    0.813551] 0x000000400000-0x000008000000 : "ubi"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Koen Vandeputte
3c3825436e kernel: bump 4.19 to 4.19.115
Refreshed all patches.

Remove upstreamed:
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Fixes:
- CVE-2020-8647
- CVE-2020-8648 (potentially)
- CVE-2020-8649

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Koen Vandeputte
e31d158c4d kernel: bump 4.14 to 4.14.176
Refreshed all patches.

Remove upstreamed:
- 0001-net-thunderx-workaround-BGX-TX-Underflow-issue.patch
- 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
- 184-USB-serial-option-add-Wistron-Neweb-D19Q1.patch

Fixes:
- CVE-2020-8648 (potentially)
- CVE-2020-8647
- CVE-2020-8649

Compile-tested on: cns3xxx, octeontx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-04-16 13:23:11 +02:00
Hannu Nyman
a7423fef32 ath79: improve status LED definitions for GL-AR750
Improve the status LED functionality in GL-AR750
by adding the definitions for different statuses
(boot, failsafe, running, flashing).

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2020-04-16 00:02:03 +02:00
Adrian Schmutzler
508462a399 ath79: add SUPPORTED_DEVICES for TP-Link TL-WA901ND v2
This adds the board name from ar71xx to support upgrade without
-F for the TP-Link TL-WA901ND v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-15 12:47:43 +02:00
Chuanhong Guo
ad19751edc ramips: mt7621: enable lzma-loader for some devices
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-15 10:14:19 +08:00
Paul Spooren
f814121600 x86: append metadata to combined images
Now that the x86 target uses the new image generation code we can also
attach metadata to the created images.

As currently the `SUPPORTED_DEVICES` list is empty, no JSON metadata is
attached, however the signing happens in the same step.

This results in signature verification for x86 images.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-04-14 23:38:08 +01:00
Petr Štetiar
0bea89a1d0 kernel: bump 5.4 to 5.4.32
Refreshed patches, removed upstreamed patches:

 generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch

Run tested: qemu-x86-64, apalis
Build tested: x86/64, imx6, sunxi/a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-14 21:58:16 +02:00
Ansuel Smith
9abf01246e ipq806x: add patch to fix broken buttons
From kernel 4.20 msm-gpio driver is broken and cause the
malfunction of the buttons on every ipq806x target.
Add a patch to fix this.

Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2020-04-14 21:58:16 +02:00
Adrian Schmutzler
d0cb6e995b ath79: further fixes for ZyXEL NBG6716
This applies further fixes to the DTS of ZyXEL NBG6716 based on
what is found in ar71xx (mach-nbg6716.c):

- use WiFi label names as in ar71xx
- fix WPS gpio number
- fix GPIO_ACTIVE_HIGH and mode for WiFi switch
- add codes for USB eject buttons
- fix node name for "internet" LED

This device has separate LEDs for WAN and "Internet". As the WAN-LED
(and the four LAN-LEDs) are driven independent of the setup in
DT/01_leds, the "internet" LED is left unassigned (in contrast to
ar71xx, where it was set up effectively as a second WAN LED)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-14 12:03:57 +02:00
Chuanhong Guo
75f19deb3a ramips: define image recipe for uncompressed uimage with loader
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 12:01:50 +08:00
Chuanhong Guo
d9e9a0e6b1 ramips: define lzma loader platform in target
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:17:47 +08:00
Chuanhong Guo
111029bea7 ramips: add missing DEVICE_VARS for lzma-loader
LOADER_TYPE is a per-device variable which should be included in
DEVICE_VARS.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:14:15 +08:00
Luiz Angelo Daros de Luca
1b2c4af039 ath79: enable m25p,fast-read for tplink,tl-wr1043-v1
Enables spi-mem interface for 3x faster flash read.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Luiz Angelo Daros de Luca
e430dfdd69 ath79: enable m25p,fast-read for tplink,tl-wr2543-v1
Enables spi-mem interface usage. It speeds up flash read
in about 3x while it also workaround a possible hardware
bug when normal spi read is used.

Fixes: FS#2742

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Luiz Angelo Daros de Luca
b3f9842330 ath79: add read support using spi-mem
Reimplements read optimization on top of spi-mem. Similar to
what 461-spi-ath79-add-fast-flash-read.patch used to do with
the dropped flash read interface.

It accelerate only fast-read op reading flash directly from
memory mapped region. 'm25p,fast-read' must be set in order
to use the new spi-mem.

It improved read speed up to 3x on old devices (tplink,tl-wr2543-v1)
while no speed improvement was noticed on newer devices like
(tplink,archer-c7-v2).

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2020-04-14 10:47:23 +08:00
Alberto Bursi
35f208da3c x86: add nforce eth to default packages
forcedeth is necessary to use the integrated
ethernet controller of Nvidia nForce chipset.

There are PC motherboards with this chipset
from 2001 that run 32bit Athlon XP CPUs and
more modern ones up to 2009 that can run Intel
and AMD 64bit processors, so add this to
all non-geode x86 targets.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-04-13 22:41:37 +02:00
Tomasz Maciej Nowak
779a1c84ea mvebu: drop armada-37xx PCI aardvark patches
These patches were necessarry for Atheros and some Intel WiFi cards.
After short testing, the current upstream driver state is enough for
these WiFi cards to work. If there are still some issues with other
devices, the patches could be easily restored.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-13 22:41:37 +02:00
DENG Qingfang
f72a13b537 mvebu: refresh config
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
d13fe4127c mvebu: refresh patches
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
ae183c128f mvebu: set kernel testing version to 5.4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
DENG Qingfang
70193703a9 mvebu: copy files and patches to 5.4
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-13 22:41:37 +02:00
Daniel González Cabanelas
85ef69b202 mvebu: add support for Buffalo LinkStation LS421DE
Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370

Hardware:
   SoC:         Marvell Armada 88F6707-A1
   CPU:         Cortex-A9 1200 MHz, 1 core
   Flash:       SPI-NOR 1 MiB, NAND 512 MiB
   RAM:         DDR3 512 MiB
   Ethernet:    1x 10/100/1000 Mbps
   USB:         1x 2.0, 1x 3.0
   SATA:        2x 3.0 Gbps
   LEDs/Input : 5x / 2x (1x button, 1x slide-switch)
   RTC:         Ricoh RS5C372A, I2C, no battery

Flash instruction (UART+TFTP):
  1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13)
  2. Remove any hard drive from inside the bays.
  3. Boot the Openwrt initramfs image using the U-Boot serial console:
         tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin
         bootm 0x1200000
  4. Flash the sysupgrade image using the Openwrt console:
         sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin
  5. Wait until it finish, the device will reboot with Openwrt installed
     on the NAND flash.

Note:
  - Device shuting down doesn't work, even if the power slide switch is
    used. We must first, via MDIO, set the unused LED2 at the ethernet
    phy0 to off state. Reboot works ok.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-13 22:41:14 +02:00
Aleksander Jan Bajkowski
b43023b7ba kernel: remove non-existant symbols
These symbols exist only in older kernels and can be removed.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-04-13 22:40:19 +02:00
Adrian Schmutzler
97af28d23e ath79: fix USB port LED assignment for ZyXEL NBG6716
The USB LED assignment to internal ports was swapped.

Fix it.

We also explicitly checked that the LED label numbers match those
on the device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-13 19:22:16 +02:00
Guillaume Lefebvre
f5a9181d6e ath79: fix wmac initialization for Zyxel NBG6716
2.4 GHz Wifi on ath79 is set up in 10-ath9k-eeprom, but in ar71xx
it was done with ath79_register_wmac.

Thus, the following errors are observed on the device:
ath: phy1: Unable to initialize hardware; initialization status: -5
ath9k 18100000.wmac: failed to initialize device
ath9k: probe of 18100000.wmac failed with error -5

This patch changes the ath79 support to properly use wmac as well.
This will also require fixing the MAC address in a different way.

Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
[several adjustments to 10-fix-wifi-mac, use correct MAC address,
rewrite commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-13 19:21:56 +02:00
Chuanhong Guo
77b99ea3c6 ramips: fix whitespace in 990_NET-no-auto-carrier-support.patch
Fixes: 6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-13 11:49:16 +08:00
Chuanhong Guo
4d06229242 ramips: ralink-eth: fix leftover dma dev argument
Fixes: 05dee5833a ("ramips: ralink-eth: fix device struct passed to dma functions")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-13 11:32:50 +08:00
Jonas Gorski
4e535d81ee bcm63xx: disable all devices with <= 4MiB flash and <= 32 MiB RAM
Device with 4 MiB flash and 32 MiB RAM won't be able to run OpenWrt in
a sufficient manner without tweaks, so don't build images for them by
default.

This includes all BCM6338, BCM6345 and BCM6348 "generic" devices,
as there are no supported devices of these with more than that.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2020-04-12 20:45:21 +02:00
Chuanhong Guo
b756ea2a90 ramips: replace pinctrl property names
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
8f6334eb94 ramips: explicitly disable built-in switch when needed
previously we rely on the failsafe setup in preinit scripts to disable
built-in switch implicitly for single-port devices. This doesn't work
anymore due to preinit script removal.
this patch explicitly disable built-in switch for needed devices.

Fixes: a8d62a4eb1 ("ramips: remove set_preinit_iface script")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:29:17 +08:00
Chuanhong Guo
605a7ffff2 ramips: add 5.4 as testing kernel
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
abadee5d60 ramips: mt76x8: switch to kernel 5.4
4.14 doesn't work anymore due to gpio dt binding changes. Switch mt76x8
to 5.4 directly.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
d7d46da938 ramips: disable images for 4M devices
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
e29e2a9484 ramips: ralink-eth: add support for 5.4 kernel
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
0b68d081eb ramips: mt7628: update dts for upstream gpio-mt7621 driver
upstream driver merged 3 separated gpio banks into one gpio node.
and gpioX Y in our local driver should be replaced with gpio X*32+Y.

This patch is created using the following sed command:
sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge'

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
e320435a6a ramips: refresh kernel config for 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
89bf2b18af ramips: copy kernel config for 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
6fcba5eec3 ramips: port 0034-NET-multi-phy-support.patch to 5.4
This hack is needed for old ethernet driver:
On mt7620, we have two exposed RGMII ports that connects to builtin
switch. However, swconfig has no way to interact with phy subsystem.
As a result, we have to register both PHYs to ethernet mac instead
and this patch prevents main ethernet interface from going down due
to phy link changes.
Also rename the patch for its actual purpose.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Chuanhong Guo
05dee5833a ramips: ralink-eth: fix device struct passed to dma functions
dma functions needs the struct from platform_device instead of
the one for ethernet interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
33d027c5b8 ramips: move and rename out-of-tree mtk eth driver
move the driver into shared 'files' directory and rename all symbols
from mediatek/mtk to ralink.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
b0ec8d0ca0 ramips: increase spi frequency for newifi d1/d2
increase spi frequency for both devices to 45MHz.
while at it, also remove m25p,fast-read for newifi d1 as it's only
needed when spi clock is higher than 50MHz.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
5c8f2c64d7 ramips: enable broken-flash-reset for some 32M flash boards
These are boards known to start on 3-byte address mode, which requires
broken-flash-reset if 4B_OPCODES isn't supported by the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Chuanhong Guo
dfa521f129 generic: spi-nor: rework broken-flash-reset
Instead of resetting flash to 3B address on remove hook, this
implementation only enters 4B mode when needed, which prevents more
unexpected reboot stuck. This implementation makes it only break when
a kernel panic happens during flash operation on 16M+ areas.
Also silent broken-flash-reset warning. We are not dealing with vendors
and it's unpleasant for users to see that unnecessary and long WARN_ON
print.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:17 +08:00
Adrian Schmutzler
de3e5de8cc cns3xx: remove support for kernel 4.14
This target has been on kernel 4.19 for nine months now [1], and
has had testing support for even longer [2].
This should be long enough to drop support for kernel 4.14.

[1] 545bfbc3a9 ("cns3xxx: switch to kernel 4.19")
[2] c6bebe1a94 ("cns3xxx: add support for kernel 4.19")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 13:43:52 +02:00
Adrian Schmutzler
e8931b309f ramips: mt7621: tidy up names for Ubiquiti devices
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.

This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.

While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 13:25:42 +02:00
Adrian Schmutzler
bebc9809d1 bcm63xx: remove support for kernel 4.19
Since stable kernel for this target is still 4.14, kernel 4.19
has never been used much (and actually was broken for some devices).

So, since we bump testing kernel to 5.4, there is no real need to
keep 4.19 and have an additional version to care about.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:48:38 +02:00
Adrian Schmutzler
51b07e782d bcm63xx: use kernel 5.4 as testing kernel
This uses 5.4 as testing kernel. Since 4.19 has not seen broad
testing yet, just keep 4.14 as stable kernel until 5.4 is ready.

Tested on Comtrend AR-5387un (Thanks to @Noltari).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:46:26 +02:00
Adrian Schmutzler
cb2f0df784 bcm63xx: 5.4: fix compilation for changed driver_find_device
In kernel patch 92ce7e83b4e5 ("driver_find_device: Unify the match
function with class_find_device()") the arguments of functions used
with driver_find_device are adjusted. Do the same for our local
user.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:45:56 +02:00
Adrian Schmutzler
8a2118e1b4 bcm63xx: 5.4: add removed helper syscon_regmap_lookup_by_pdevname
The helper syscon_regmap_lookup_by_pdevname has been removed in kernel patch
29d14b668d2f ("mfd: Remove unused helper syscon_regmap_lookup_by_pdevname")
due to lack of users.

However, we use this function in our local pinctrl drivers for BCM6358 and
BCM6368. Thus, we have to add it locally.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:44:57 +02:00
Adrian Schmutzler
43d3ef91f1 bcm63xx: prevent fall-through in kernel patches for 5.4
In kernel 5.4 -Werror=implicit-fallthrough is treated as error:

arch/mips/bcm63xx/cpu.c: In function 'detect_cpu_clock':
arch/mips/bcm63xx/cpu.c:158:2: error: this statement may fall through [-Werror=implicit-fallthrough=]
  {
  ^
arch/mips/bcm63xx/cpu.c:179:2: note: here
  case BCM6328_CPU_ID:
  ^~~~
cc1: all warnings being treated as errors

This can be fixed by adding "Fall through" as a comment where intended,
and has to be fixed by returning a proper default otherwise.

In case of the default clock frequency for BCM6318 we fixed this by
returning the default value taken from BCM6328 and BCM6362.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:43:55 +02:00
Adrian Schmutzler
6c521f6828 bcm63xx: fix missing watchdog core dependency
This patch follows the other patches that added the watchdog
core to various (armvirt, malta, ath79, ...) targets that
have been hit by the following build error:

Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko

In theory, we could have just added the CONFIG_WATCHDOG_CORE=y
to the Kconfig variable of kmod-hwmon-sch5627's package definition.
This would have forced the watchdog core to be builtin and less
architectures would need to be updated. But we might as well follow
through here.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:40:06 +02:00
Adrian Schmutzler
f0fbc47a91 bcm63xx: update config for kernel 5.4
Update config with make kernel_oldconfig.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:39:22 +02:00
Adrian Schmutzler
04c07e05a1 bcm63xx: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.

The removed patches have been merged upstream.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:36:43 +02:00
Adrian Schmutzler
f8f1dc6eab bcm63xx: copy files to kernel 5.4
Copy config and patches to kernel 5.4.
make kernel_oldconfig has been run on 4.19 beforehand.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 12:36:21 +02:00
Yanase Yuki
e66becb490 ramips: add support for I-O DATA WN-AX2033GR
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.

Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V

This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.

Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".

Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
   https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 00:43:09 +02:00
Jo-Philipp Wich
93294b516e generic: drop 616-net_optimize_xfrm_calls.patch
The conditional check introduced by this patch may trigger a NULL pointer
dereference in case the result of dev_net() is NULL.

Since the purpose of this patch is neither sufficiently explained and since
this patch apparently has never been submitted upstream despite it being in
the pending-* patch directory, I propose to drop it without replacement.

If the performance implications of dropping this patch are found to be
significiant, it should be reintroduced with proper description and
benchmark results.

Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2943
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-04-12 00:08:05 +02:00
Pawel Dembicki
c30220d458 ipq40xx: add support for Cell C RTL30VW
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.

This is stripped version of ASKEY RTL0030VW.

Hardware:

Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP

Known issues:

None so far.

Instruction install:

There are two methods: Factory web-gui and serial + tftp.

Web-gui:
1. Apply factory image via stock web-gui.

Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.

4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000

5. Install sysupgrade image via "sysupgrade -n"

Back to stock:

All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:

1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.

Based on work: Cezary Jackiewicz <cezary@eko.one.pl>

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-10 15:22:26 +02:00
DENG Qingfang
a30abb1b6b ipq40xx: add support for MobiPromo CM520-79F
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019

Specification:

SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
      2 (USB, CAN) are GPIO
      other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset

Flash instruction:
Disassemble the router, connect UART pins like this:
 GND TX    RX
  [x x . . x .]
  [. . . . . .]

(QCA8075 and IPQ4019 below)
Baud-rate: 115200

Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
	printenv
	(Copy the output to somewhere save)
Set bootenv:
	setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
	setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
	setenv cm520_boot 'run set_ubi; run bootkernel'
	setenv bootcmd 'run cm520_boot'
	setenv bootargs
	saveenv
Boot initramfs from TFTP:
	tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
	bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
	cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP

Upload nand-factory.ubi to /tmp via SCP, then run
	mtd erase rootfs
	mtd write /tmp/*nand-factory.ubi rootfs
	reboot

To revert to stock image, restore default bootenv in uboot UART console
	setenv bootcmd 'bootipq'
	printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
	saveenv
upload the backed up mtd12.bin and run
	tftpboot mtd12.bin
	nand erase 0xb80000 0x7480000
	nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
	cd /tmp
	cat /dev/mtd7 > mtd7.bin
	echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
	for i in 28 48 68 108; do
		dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
	done
	mtd write mtd7.bin BOOTCONFIG
	mtd write mtd7.bin BOOTCONFIG1

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:22:26 +02:00
Christian Lamparter
8ce138607e apm821xx: use the real default HZ value from upstream
With the "real HZ" debate out of the way, let's actually
use the apm821xx's default upstream config file at
arch/powerpc/configs/44x/bluestone_defconfig. From what
I can tell, it sets NO_HZ (well, this platform was for
NAS, so this is a bit unexpected) and remove any specific
HZ_$VALUE symbol.

Sadly, Daniel Engberg didn't run any before/after netperf
tests, because it would have been such a slam dunk across
the boards. In case of the apm821xx the tcp tx/rx
performance improved ~14% (from 600Mbps to 700Mps).
This now causes the emac to drop frames too, so let's see
if this is causes more problems or not.

This patch includes a refresh of the configuration too.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-04-10 15:20:30 +02:00