Commit Graph

175 Commits

Author SHA1 Message Date
Adrian Schmutzler
0104eed1e5 ath79: add support for TP-Link CPE510 v1
TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with
two Ethernet ports based on Atheros AR9334

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 2T2R 5 GHz
 - 13 dBi built-in antenna
 - Power, LAN0, LAN1 green LEDs
 - 4x green RSSI LEDs

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Based on the work of Paul Wassi <p.wassi@gmx.at>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
08857e69be ath79: add support for TP-Link CPE210 v1
Specifications:

    * SoC: Qualcomm Atheros AR9344 (560 MHz)
    * RAM: 64MB
    * Storage: 8 MB
    * Wireless: 2.4GHz N based built into SoC 2x2
    * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:

Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Adrian Schmutzler
c02b9818a5 ath79: add support for TP9343-based TP-Link TL-WR94x devices
This adds support for several TP-Link devices based on TP9343
("a QCA9561 without PCIe and USB"):
- TL-WR940N v3
- TL-WR940N v4
- TL-WR941ND v6

The devices are only different concerning LEDs and MAC address
assignment.

All TL-WR940 are with non-detachable antennas (N), all
TL-WR941 devices are with detachable antennas (ND).

Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to * (see below)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

* TFTP image names:
940 v3: wr941ndv6_tp_recovery.bin
940 v4: wr940nv4_tp_recovery.bin
941 v6: wr941ndv6_tp_recovery.bin

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-05 21:50:15 +02:00
Jackson Lim
030fc6ab6c ath79: add support for D-Link DIR-842 C1
Hardware spec of DIR-842 C1:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[fix whitespace issues]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-05 10:54:11 +02:00
Adrian Schmutzler
8b76c6695b ath79: add support for TP-Link TL-WR841N/ND v12
This router has the same hardware as TP-LINK TL-WR841N/ND v11 (same
FCC ID, same TFTP image name...).

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv11_tp_recovery.bin
   (it's really v11, not v12)
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-05 10:54:11 +02:00
Adrian Schmutzler
4254193c1d ath79: add support for TP-Link TL-WR841N/ND v10
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to wr841nv10_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-05 10:54:11 +02:00
Roger Pueyo Centelles
334bbc5198 ath79: add support for ALFA Network AP121F
This commit ports support for the ALFA Network AP121F, a pocket-size
router with 1 Ethernet and 2.4 GHz WiFi based on the AR9331 SoC, to the
ath79 target (it was already supported in ar71xx; see commit 0c6165d2
for more details).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[pepe2k@gmail.com: fixed GPIO polarity, included USB support, changed
DTS nodes order, moved WLAN LED trigger define to DTS, made U-Boot env
partition writable]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-07-31 08:38:01 +02:00
Adrian Schmutzler
273b803623 ath79: fix indent in 01_leds
Change capitalization from spaces to tabs in order to match
the style of the file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fix capitalization in commit title, add short description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-24 20:36:27 +02:00
Jackson Lim
209b368254 ath79: add support for D-Link DIR-842 C2
Hardware spec of DIR-842 C2:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: 2.0

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[Reword reset-hog comment, fix formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-24 11:36:02 +02:00
Adrian Schmutzler
974d6958a7 ath79: Add support for TP-Link Archer C60 v2
TP-Link Archer C60 v2 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

Flash instruction (under U-Boot, using UART):
tftp 0x81000000 ...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-18 00:06:55 +02:00
Adrian Schmutzler
6d313da6dc ath79: Add support for TP-Link Archer C60 v1
TP-Link Archer C60v1 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 ...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-18 00:06:55 +02:00
Andrew Cameron
cad4132e00 ath79: add support for TP-Link CPE510-v2/v3
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - Based on the same underlying hardware as the TP-Link CPE510
 - Power, LAN, and 4 green LEDs
 - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in)
 - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
 - Adjustable transmission power from 0 to 23dBm/200mw

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-18 00:06:55 +02:00
Pramod Pancha
8e384ba830 ath79: add support for Trendnet TEW-823DRU
Trendnet TEW-823DRU is a dual-band AC1750 router.
The router is based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

720 MHz CPU
256 MB of RAM
16 MB of FLASH
3T3R 2.4 GHz
3T3R 5 GHz
5x 10/100/1000 Mbps Ethernet

Firmware can be flashed from the web interface. Tested on 3 routers
with no issues.

Signed-off-by: Pramod Pancha <pancha@vill.com>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-18 00:06:55 +02:00
Christoph Krapp
6fde0b735c ath79: add support for TP-Link RE355 v1 and RE450 v1
Specification:

SoC: Qualcomm Atheros QCA9558
RAM: 64/128MiB
Flash: 8MiB SPI-NOR
Wifi:
  - 2.4GHz: 3T3R (QCA9558)
  - 5GHz: 3T3R (QCA9880)
LAN: 1x 10/100/1000 Mbps
UART:
  - TP1: Tx
  - TP2: Rx
  - TP3: Gnd
  - TP4: 3v3

Flash instructions:
Flash factory image through stock firmware WEB UI.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-07-17 23:14:23 +02:00
Daniel Gimpelevich
bc18c2bfe7 ath79: add support for Bluesocket BSAP1880 board
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.

Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B

Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
   115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
   file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
   load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80060000 -l LeNgTh vmlinux_2
   load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
   use a hexadecimal calculator to subtract the start from the end in order
   to substitute it below, with the leading "0x" to specify it in
   hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
   reset
10.Wait for the status LED to go solid green

Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-17 22:59:29 +02:00
Chuanhong Guo
a9360452f0 ath79: add support for Qihoo C301
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882

Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:51:03 +08:00
David Bauer
cb3cd52694 ath79: add support for devolo WiFi pro 1750x
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED Power (non-controllable)
       1x LED Status (internal)
       1x LED LAN (controlled by PHY)
       1x LED WLAN
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to external-LED header.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-14 16:20:53 +02:00
Adrian Schmutzler
ab02584685 ath79: Use -v1 suffix for TP-Link WDR3600/4300
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.

Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.

This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-03 07:45:00 +02:00
Andrew Cameron
e15049c88b ath79: add support for TP-Link CPE610-v1
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - Based on the same underlying hardware as the TP-Link CPE510
 - Power, LAN, WLAN5G green LEDs
 - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2019-06-24 20:22:24 +02:00
Adrian Schmutzler
fde0abf267 ath79: Add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
Adrian Schmutzler
409940cef4 ath79: Reorder some TP-Link Archer devices in 01_leds
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
Adrian Schmutzler
fcb920ffe7 ath79: Consistently label art partition with lower case
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Adrian Schmutzler
3d153323ab ath79: Consistently label info partition
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.

This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.

This patch relabels those partitions in ath79 to consistently use
'info'.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Rytis Zigmantavičius
64493d42b4 ath79: add support for 8devices Carambola2 development board
Specifications:
- Atheros AR9331 (400 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 1T1R 2.4 Wlan (AR9331)
- 2x 10/100 Mbps Ethernet
- 3x LEDs, 1x gpio button
- 1x USB 2.0, 5V
- UART over usb, 115200n8

Upgrading from ar71xx target:
- Put image into board:
    scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \
        root@192.168.1.1/tmp/
- Run sysupgrade
    sysupgrade /tmp/sysupgrade.bin

Upgrading from u-boot:
- Set up tftp server with sysupgrade.bin image
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
    setenv serverip 192.168.1.254
- Set device ip from same subnet
    setenv ipaddr 192.168.1.1
- Copy new firmware to board
    tftpboot 0x81000000 sysupgrade.bin
- erase flash
    erase 0x9f050000 +${filesize}
- flash firmware
    cp.b 0x81000000 0x9f050000 ${filesize}
- Reset board
    reset

Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com>
[wrapped long line in commit description, whitespace and art address
 fix in DTS, keep default lan/wan setup, removed -n in sysupgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:24:45 +02:00
Kristian Evensen
046263095e ath79: Add support for ZBT-WD323
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:

* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)

Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232

Intallation and recovery:

The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated.  The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).

While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware.  Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.

Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:24:36 +02:00
Chuanhong Guo
c3a8518918 ath79: fix default config for devices with eth0/eth1 swapped
also fix the following problems in this commit:
glinet,gl-ar150: This router uses an uncommon order of setting up gmacs
                 in ar71xx. gmac0 is preferred to be wan port because of
                 the additional link status info available. So this
                 router will have eth0/eth1 swapped comparing to ar71xx.
tplink,tl-wr710n-v1: same as gl-ar150
embeddedwireless,dorin: eth0 is used as switch port, which was incorrect.
                        It's correct now, so keep this one untouched.
tplink,tl-wr842n-v1: we don't swap PHYs on ar7241 so the original port order
                     is incorrect.
reorder archer-a7-v5 entry.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:12:31 +02:00
Chuanhong Guo
f84715d463 ath79: rework LED configurations for tplink,archer-d50-v1
The original one has the following problem:
1. Port mask of lan led includes wan port.
2. By using netdev trigger with vlan port, the link led
   is always on.

This commits fixes the above problems by correcting port
mask for lan led and use swconfig trigger for wan leds.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:12:31 +02:00
Ryan Mounce
6d6985ff0e ath79: add support for WD My Net N750
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.

Tested sysupgrade + factory flash from WD Emergency Recovery

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2019-05-27 22:44:08 +02:00
Davide Fioravanti
f5d2c91415 ath79: add support for TP-Link Archer D50 V1
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.

Internally eth0 is connected to the Broadcom CPU.

Router section - Specification:

CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB

Known issues:
DSL not working (eth0) (WIP)

UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC

J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX

The following instructions require a connection to the J2 UART header.

Flash instruction under U-Boot, using UART
------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +$filesize
	cp.b 0x81000000 0x9f020000 $filesize
	reset

Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
	bootm 0x81000000

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
 4. Double check the .mod file size. It must be 7995392 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
        tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
        erase 0x9f020000 +$filesize
        cp.b 0x81000000 0x9f020000 $filesize
        reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
2019-05-18 17:59:49 +02:00
Chris Blake
aee5c98619 ath79: add support for Aruba AP-105
SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud

Factory installation:

 - Needs a u-boot replacement. See Wiki for
   information on how to do a in-circut flash with
   a SPI-Flasher like a CH314A or flashrom. Wiki page
   can be found at https://openwrt.org/toh/aruba/aruba_ap-105

 - Be careful when dis- and reassembling the device to
   not squish any of the antenna cables in the process!

 - Be sure to make a full 16 MiB backup of your device
   before flashing the new u-boot! This is needed if you
   ever have interest in reverting back to stock firmware.

Not working:

 - TPM (needs a driver)

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2019-05-18 16:44:41 +02:00
Adrian Schmutzler
d4b89b7170 ath79: Add support for TP-Link TL-WR1043N v5
Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM Zentel A3R12E40CBF-8E
 - 16 MB flash Winbond W25Q128FVSG
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>

Installation on HW rev.5:

Factory firmware can be installed via the WEB interface.

Alternatively, it is also possible to use a TFTP server
for recovery purposes:
 - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
 - Set static IP of your PC to *192.168.0.66*
 - Router will obtain IP 192.168.0.86 for a few seconds while
   loading, when reset button pressed at power On.

And finally, there's always u-boot access through the UART.
For information visit the wiki.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message]
2019-05-18 16:38:18 +02:00
sven friedmann
30dcbc741d ath79: add support for EnGenius ECB1750
Specification:

- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)

https://fccid.io/A8J-ECB1750

Tested and working:

- lan, wireless, leds, sysupgrade (tftp)

Flash instructions:

1.) tftp recovery

- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade

2.) oem webinterface factory install (not tested)

Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".

3.) oem webinterface command injection

OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.

https://openwrt.org/toh/engenius/engenius_ecb1750_1

Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
2019-05-18 13:43:55 +02:00
Sven Roederer
e0d98e120a ath79: add TP-Link WR842N v3
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).

Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)

Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)

Thanks to Holger Drefs for providing the hardware

Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2019-04-13 14:39:59 +02:00
Daniel Gimpelevich
f61e754522 ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Adrian Schmutzler
0a13f589c3 ath79: Correct MAC address for WAN interface of Archer A7/C7 v5
These devices share the network config with C7v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Christian Mauderer
8a4dc6f48c ath79: add support for Ubiquiti airCube ISP
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.

SoC:       Qualcomm / Atheros QCA9533-BL3A
RAM:       64 MB DDR2
Flash:     16 MB SPI NOR
Ethernet:  4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS:      1x via a SPI controller (not yet supported)
Buttons:   1x Reset
Serial:    1x (only RX and TX); 115200 baud, 8N1

Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
  (Needs RSA signed images, for details see PR#1958)

The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND

Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
  key to stop autoboot` is displayed. Note: Pressing space multiple
  times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
  running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
  image to the server.
- Set the U-Boot server IP with
    setenv serverip 192.168.1.100
- Load the flash image to RAM with
    tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
    erase 0x9f050000 0x9ffaffff
- Write the new flash content with
    cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
    reset

Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Markus Scheck
de2f888024 ath79: add support for OCEDO Ursus
SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
INAGAKI Hiroshi
643fcfc8d6 ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
2019-04-06 19:14:06 +02:00
Adrian Schmutzler
141698ce8f ath79: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-02 02:10:59 +02:00
Mario Schroen
5ec205d7ac ath79: Add support for TP-Link CPE210 v3
Specifications:

    * SoC: Qualcomm Atheros QCA9533 (650MHz)
    * RAM: 64MB
    * Storage: 8 MB SPI NOR
    * Wireless: 2.4GHz N based built into SoC 2x2
    * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
    Flash factory image through stock firmware WEB UI or TFTP
    To get to TFTP recovery just hold reset button while powering
    on for around 4-5 seconds and release.
    Rename factory image to recovery.bin
    Stock TFTP server IP:192.168.0.100
    Stock device TFTP adress:192.168.0.254

Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.

Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-02 02:10:59 +02:00
Ding Tengfei
acf149d531 ath79: add support for COMFAST CF-E5/E7
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.

Short specification:

    2x 10/100 Mbps Ethernet, with 24v PoE support
    64 MB of RAM (DDR2)
    16 MB of FLASH (SPI)
    2T2R 2.4 GHz, 802.11b/g/n
    built-in 1x 3 dBi antennas
    output power (max): 80 mW (19 dBm)
    Qucetel EC20 LTE MODULE(1x external detachable antenna)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:27 +01:00
Marcin Jurkowski
fcc716e21d ath79: add TP-Link TL-WR710N v1
This commit adds support for TP-Link TL-WR710N v1 router.

CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset

Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/18100000.wmac`.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
2019-03-24 01:44:27 +01:00
Chuanhong Guo
8de907c441 ath79: add support for TP-Link TL-WR941N v7 (CN)
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.

Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:27 +01:00
Tobias Schramm
d78e229903 ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.

CPU:   Atheros AR9342 SoC
RAM:   64 MB DDR2
Flash: 16 MB NOR SPI
WLAN:  QCA988X
Ports: 1x GbE

Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.

Serial flashing:

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Flashing through factory firmware:

1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot

Thanks to @cybermaus for testing!

Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-03-22 00:40:29 +01:00
Andreas Ziegler
78b9d57882 ath79: GL.iNet AR300M-nand/nor: correct LAN LED
The port labled as "LAN" is eth1.
That's different from the -lite variant,
where the only existing port eth0 is used as LAN

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2019-03-21 00:57:54 +01:00
Sven Roederer
f1396ac753 ath79: align naming of Ubiquiti Nanostation M
Support for the Nanostation M (XW) was added in 40530c8eb with board
name "nanostation-m-xw". The current image for the "Nanostation M"
uses "nano-m" as the board name.
This commit renames it to the full product name as it's used by all
other boards. The legacy boardname of the ar71xx target is added
via SUPPORTED_DEVICES to ease switching to ath79 target.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[touch-ups on the commit message, removed subject remains]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-18 20:55:24 +01:00
Tomasz Maciej Nowak
b3a0c97b8c ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.

Specification
SoC:		Atheros AR7161
RAM:		64 MB DDR
Flash:		16 MB SPI NOR
Ethernet:	2x 10/100/1000 Mbps AR8316
		LAN (CN11), WAN/PoE (CN6 - close to power barrel
		connector, 48 V)
MiniPCI:	2x
LEDS:		4x, which 3 are GPIO controlled
Buttons:	2x GPIO controlled
		Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial:		1x (only RX and TX are wired)
		baud: 115200, parity: none, flow control: none

Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.

Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
   process and enter RedBoot (bootloader) command line by pressing
   Ctrl+C,
4. Enter following commands (replace variable accordingly),
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_adress>
    (confirm storing the value by inputting y and pressing Enter)
    reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.

Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
   pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_address>
    (confirm storing the value by inputting y and pressing Enter)
    ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
    load -r -b 0x80060000 <openwrt_initramfs_image_name>
    exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
   is ready for configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:43:09 +01:00
Tomasz Maciej Nowak
ee34740ca3 ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.

Specification
SoC:		Qualcomm Atheros QCA9558
RAM:		256 MB DDR2
Flash:		16 MB SPI NOR
WIFI:		2.4 GHz 3T3R integrated
		5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet:	5x 10/100/1000 Mbps QCA8337N
USB:		1x 2.0
LEDS:		4x GPIO controlled
Buttons:	2x GPIO controlled
UART:		4 pin header, starting count from white triangle on PCB
		1. VCC 3.3V, 2. GND, 3. TX, 4. RX
		baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
   image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
   then router ip (default is 192.168.99.9) and for last, image name
   downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
   You can observe progress on console, it'll take few minutes and when
   the Power LED will stop blinking, router is ready for configuration.

Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-13 16:25:35 +01:00
Jeff Kletsky
fefa34def8 ath79: Add GL.iNet AR-300M-Lite
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.

Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
   * Do not preserve settings
   * Access rebooted device via Ethernet at OpenWrt default address

Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds

Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-03-13 16:25:34 +01:00
Santiago Piccinini
24463d0d94 ath79: add support for LibreRouter v1
Hardware
--------
SOC:   QCA9558
RAM:   128M DDR2
Flash: 16MiB SPI-NOR
ETH:   QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN:   1x Reset
GPIO:  multiple GPIO on header, PoE passthrough enable
UART:  3.3V 115200 8N1 header on the board
WDG:   ATTiny13 watchdog
JTAG:  header on the board
USB:   1x connector and 1x header on the board
PoE:   10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)

OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.

Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
   header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
   interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
    ath> tftp 82000000 <your image>-sysupgrade.bin
    ath> erase 0x9f050000 +$filesize
    ath> cp.b 0x82000000 0x9f050000 $filesize
    ath> bootm 0x9f050000

More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
2019-03-13 16:25:34 +01:00