Commit Graph

2422 Commits

Author SHA1 Message Date
Adrian Schmutzler
2155e94d4b ramips: remove memory node for ZBT-WE1326
Memory auto-detection for mt7621 has just been added to 19.07
stable branch.

This removes the memory node for the ZBT-WE1326, which will support
revision 5 that has 256MiB RAM (Nanya NT5CC128M16IP-DI) instead of
512MiB (up to revision 4).

ref: #1930

This is taken from master commit a2c19f1d2f ("ramips: dts: drop
memory nodes"), where _all_ memory nodes were removed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-11 22:31:24 +08:00
Chuanhong Guo
49c563a829 ramips: mt7621: add support for memory detection
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory

detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.

This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
     This only happens when some weird user decided to change
     kernel load address to 256m or higher address. Since this
     is a quite unusual case, we just skip 512m testing and return
     256m as memory size.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 6d91ddf517)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-11 22:31:22 +08:00
Koen Vandeputte
c4b514b200 kernel: bump 4.14 to 4.14.147
Refreshed all patches.

Altered patches:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ar71xx)
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch (ath79)

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Compile-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-10-08 12:45:13 +02:00
David Bauer
250d57ac29 ramips: add factory image for NETGEAR R6220
This adds an easy-installation factory image for the NETGEAR R6220
router. The factory image can either be flashed via the vendor Web-UI or
the bootloader using nmrpflash.

Tested with NETGEAR V1.1.0.86 firmware.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 607dfdf211)
2019-09-16 21:43:39 +02:00
Adrian Schmutzler
d889cc9887 ramips: fix ethernet MAC address of ASUS RT-AC57U
This backports the only non-cosmetic fix from 6640e1c368
("ramips: clean and improve MAC address setup in 02_network").

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-09 21:12:23 +08:00
Adrian Schmutzler
79b9bc44d6 ramips: fix duplicate network setup for dlink, dir-615-h1
In 555ca422d1 ("ramips: fix D-Link DIR-615 H1 switch port
mapping"), port setup for dir-615-h1 was changed without removing
the old one. This was working as the new one was triggered earlier
than the old one.

(In the meantine, changed sorting during ramips rename patches
actually inversed that order.)

Anyway, just remove the wrong case now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit e35e4a996e)
2019-09-09 21:12:23 +08:00
Adrian Schmutzler
f9ecee7913 ramips: remove duplicate case for MAC setup of freestation5
ARC FreeStation5 is present twice in MAC address setup.

>From older commits/changes, it is not possible to reconstruct
the correct choice only by reading the annotations.

Thus, remove the second case and keep the first one, so behavior
stays the same (as nobody seems to have complained about it).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit ad4eb2241b)
2019-09-09 21:12:23 +08:00
Hauke Mehrtens
6d2044d62f mt7620: disable image generation for Nexx WT3020 (4MB)
Image generation is currently failing on builbots due to the following
error:

WARNING: Image file openwrt-19.07-snapshot-r10495-db5164d3d0-ramips-mt7620-wt3020-4M-squashfs-factory.bin is too big

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-09-08 21:08:22 +02:00
Rafał Miłecki
5ae87c76b7 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8b4bc7abe0)
[rmilecki: dropping ARGV without this change broke sysupgrade]
Fixes: 6ac62c4b6c ("base-files: don't set ARGV and ARGC")
2019-09-07 14:31:16 +02:00
David Bauer
15d84131fe ramips: fix network setup for various NETGEAR boards
There are currently the following issues present for the Netgear R6220,
R6350 and WNDR3700 v5:

 - LAN and WAN MAC-addresses are inverted
 - WAN MAC-address is off. It are +2 compared to the LAN MAC-address
   (R6350 only)
 - Switchport order is inverted in LuCi

This commit fixes both these issues by assigning correct MAC-addresses
to LAN and WAN interfaces and defining the switchports with the correct
labels.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 13937a16d4)
2019-09-07 00:59:41 +02:00
David Bauer
f057133349 ramips: use phy trigger for various Netgear boards
This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit fa46c9b208)
2019-09-07 00:59:41 +02:00
David Bauer
b8b62b8506 ramips: disable badblock shifting for MT7621 NAND
The MediaTek MT7621 NAND driver currently intransparently shifts NAND
pages when a block is marked as bad. Because of this, offsets for e.g.
caldata and MAC-addresses seem to be off.

This is, howeer, not a task for the mtd NAND driver, as the flash
translation layer is tasked with this.

This patch disables this badblock shifting. This fix was originally
proposed by Jo-Philipp Wich at
https://bugs.openwrt.org/index.php?do=details&task_id=1926

Fixes FS#1926 ("MTD partition offset not correctly mapped when bad
eraseblocks present")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 527832e54b)
2019-09-07 00:53:18 +02:00
David Bauer
abe137ff5e ramips: add support for ASUS RT-AC57U
SoC:   MediaTek MT7621AT
RAM:   128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi:  MediaTek MT7603EN bgn 2SS
WiFi:  MediaTek MT7612EN nac 2SS
BTN:   Reset - WPS
LED:    - Power
        - LAN {1-4}
        - WAN
        - WiFi 2.4 GHz
        - WiFi 5 GHz
        - USB
UART:  UART is present next to the Power LED.
       TX - RX - GND - 3V3 / 57600-8N1
       3V3 is the nearest one to the Power LED.

Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
 > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>

Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
 > scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
 > mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
 > reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 14e0e4f138)
2019-07-21 13:10:12 +02:00
Petr Štetiar
4022035aaf mt7620: disable image generation for Netgear EX2700
Image generation is currently failing on builbots due to the following
error:

 WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-20 23:40:20 +02:00
Chuanhong Guo
a353f2ee7f ramips: mt7621: add IRQ for GPIO node
This makes interrupt-based gpio-keys working.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 110daa16e4)
2019-06-27 17:17:23 +02:00
Koen Vandeputte
9ed98198cb kernel: bump 4.14 to 4.14.128
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-20 15:50:00 +02:00
Koen Vandeputte
4089df4f4b kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.

This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297

Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:25:41 +02:00
Kristian Evensen
86b6d31e6e ramips: Remove redundant LED-cases
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-06-10 11:25:47 +02:00
Deng Qingfang
b47cf6d539 ramips: mt7620: select kmod-rt2800-pci driver for RT5592
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages

Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-06-10 11:25:47 +02:00
Chuanhong Guo
0ab9f283f7 ramips: add support for TOTOLINK LR1200
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
        5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot

Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1

Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
   (e.g. minicom or screen). All 4 serial ports of the modem
   should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
   AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
   recognized.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:26:33 +02:00
Pawel Dembicki
9b7abd9fe2 ramips: mt7620: fix 5GHz WiFi LED on DWR-118-A1
Support for D-Link DWR-118 A1 was added before LEDs feature
in mt76x0e driver.

This fixes the 5GHz WiFi LED which was previously inverted.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-06-05 10:12:30 +02:00
Petr Štetiar
bf58bc3bd8 ramips: ethernet: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code.

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Jan Hoffmann
085f66de9a ramips: create R6220 dtsi and improve WNDR3700v5 support
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.

Performed cleanup:
 * generic DTS node names
 * regulator for usb power
 * added missing pinctrl groups
 * use switch port instead of VLAN as trigger for WAN LED

Fixes for WNDR3700v5:
 * all LEDS work
 * correct ethernet MAC addresses

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-31 11:21:22 +02:00
Markus Scheck
5ff5c9bce6 ramips: add support for Xiaomi Mi Router 4A (100M Edition)
- SoC:      MediaTek MT7628AN
- Flash:    16MB (Winbond W25Q128JV)
- RAM:      64MB
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0:    MT7628AN 2.4GHz 802.11b/g/n
- WIFI1:    MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable power-LED (two-colored, yellow/blue)
            Non-programmable internet-LED (shows WAN-activity)
- Buttons:  Reset

INSTALLATION:

1. Connect to the serial port of the router and power it up.
   If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
       > Erasing SPI Flash...
       > raspi_erase: offs:20000 len:10000
   occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
   write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
   Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.

Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
2019-05-31 11:21:22 +02:00
Davide Fioravanti
7c91144ae6 ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas

Specifications:

MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button

Known issues:
The Power LED is always ON, probably because it is connected
directly to power.

Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.

Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.

Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
  WR1000_EU_92.122.2.4987.201806261618.bin
  WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.

1) Download the original FW from the Cudy website.

   (For example WR1000_EU_92.122.2.4987.201806261618.bin)

2) Remove the header.

   dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64

3) XOR the new file with the region key.

   FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
   FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C

   You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:

   xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..

   Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
   https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)

4) Check the resulting decrypted image.

   Check if bytes from 0x20 to 0x3f are:
   4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00

   Alternatively, you can use u-boot's tool dumpimage tool to check
   if the decryption was successful. It should look like:

   # dumpimage -l stock-firmware.bin
   Image Name:   Linux Kernel Image
   Created:      Tue Jun 26 10:24:54 2018
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4406635 Bytes = 4303.35 KiB = 4.20 MiB
   Load Address: 80000000
   Entry Point:  8000c150

5) Flash it via forced firmware upgrade and don't "Keep Settings"

   CLI: sysupgrade -F -n stock-firmware.bin

   LuCI: make sure to click on the "Keep settings" checkbox
         to disable it. You'll need to do this !TWICE! because
         on the first try, LuCI will refuse the image and reset
	 the "Keep settings" to enable. However a new
         "Force upgrade" checkbox will appear as well.
         Make sure to do this very carefully!

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-31 10:36:36 +02:00
Davide Fioravanti
62ce6d58f2 ramips: unify JCG helper command definition
This patch makes the JCG helper command definition available
for every rampis target

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2019-05-31 10:30:03 +02:00
Nicholas Smith
73e0f52b6e ramips: add support for Telco Electronics X1
Hardware:
SoC:   MT7621
DRAM:  256MB DDR3
Flash: 16MB SPI-NOR
WiFi:  2.4GHz: MT7603 @ PCIe0
WiFi:  5.8GHz: MT7612 @ PCIe1
Modem: Sierra Wireless MC74xx

Interfaces:
GBE RJ45 x5
mPCIe    x2
UART     x1
I2C      x1
JTAG     x1
UIM      x1
LEDs     x6

Flash instructions:
Flash from within the factory bootloader, firmware web interface or CLI using
sysupgrade -F -n

Signed-off-by: Nicholas Smith <mips171@icloud.com>
2019-05-18 17:59:49 +02:00
Jan Hoffmann
2fdd02cc7c ramips: add factory image for WNDR3700v5
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.

The new factory image for WNDR3700v5 can be flashed using nmrpflash.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-18 16:44:41 +02:00
Liu Yu
671c9d16e3 ramips: add support for HILINK HLK-7628N
Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       128 MB
Flash:     32 MB
WIFI:      802.11n/g/b 20/40 MHz
Ethernet:  5 Port ethernet switch
UART:      2x

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.
5. After firmware is started connect via ethernet at 192.168.1.1

Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
2019-05-18 13:43:55 +02:00
Kristian Evensen
869376710d ramips: Add support for ZBT WE826-E
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:

- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button

The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address.  Upload the firmware to start the recovery
process.

How to swap SIMs:

You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-05-17 21:41:43 +02:00
Kristian Evensen
52b59a984f ramips: Add support for Head Weblink HDRM200
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:

- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)

Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button

Installation instructions:

Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:

* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.

The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.

Notes:

- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:43 +02:00
Koen Vandeputte
09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
David Bauer
a4dc519888 ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.

When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-11 16:37:11 +02:00
Deng Qingfang
367813b9b1 ramips: mt7620: fix dependencies
MT7620 integrated WMAC does not need RT2x00 PCI driver or firmware
Also corrected kmod-eeprom-93cx6 and kmod-lib-crc-itu-t dependencies
according to original Kconfig and lsmod output

This will remove some unnecessary packages from MT7620 target to
save some space

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[75 characters per line in the commit message]
2019-05-11 01:05:11 +02:00
Eike Feldmann
9e0fb5a27f ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.

Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       64 MB
Flash:     8 MB
WIFI:      802.11n/g/b 20/40 MHz
USB:       1x Port USB 2.0
Ethernet:  5 Port ethernet switch
UART:      2x

Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on.  Choose the option: "Load system code
then write to Flash via TFTP".  Choose the local device IP and the TFTP
server IP and the file name of the system image.  After if the
Bootloader will copy the image to the local flash.

Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845

Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
David Bauer
43e8c37cb4 ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 18:46:40 +02:00
Daniel Golle
66e2acad9c ramips: fix pinctrl to allow hardware i2c on WRTNODE2R
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-04-11 22:26:28 +02:00
Kip Porterfield
b812a7fa68 ramips: correct DTS for Belkin F9K1109v1 to include switch definition
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.

Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2019-04-06 19:14:06 +02:00
Chuanhong Guo
d80a1c6e2c ramips: backport mt7621-spi from linux-next-20190329
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.

Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-04-06 19:14:06 +02:00
David Bauer
b19c48dc34 ramips: enable R6120 USB power
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-06 19:14:06 +02:00
Zhao Yu
32689e93c4 ramips: add support for Youku YK-L2
Hardware spec:

CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0

Flashing instructions:

Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692

to get the bootloader and unlock firmware.

0. upgrade your router with the telnet firmware via the
   firmware upgrade page on the webui.

1. telnet 192.168.11.1 from your PC

2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
   it to the /tmp directory of the router.

3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader

4. turn off the power

5. Push the reset button while turning on the router and
   wait until LED start blinking (~10sec.)

6. Connect Ethernet port and goto http://192.168.1.1.

7. Upload the firmware to firmware restore page in webui.

Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
2019-04-06 19:13:49 +02:00
Felix Fietkau
c9262a96d1 ramips: implement vlan rx offload on MT7621
Avoids the overhead of software VLAN untagging in the network stack

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-04-03 10:40:09 +02:00
David Bauer
38f3433420 ramips: add missing SPDX identifier for EX6150
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-31 20:59:08 +02:00
Rosen Penev
2159b25466 ramips: Increase GB-PC1 SPI frequency to 80MHz
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).

Based on upstream commit: 97738374a310b9116f9c33832737e517226d3722

 time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s

 [test done with backported upstream v4.19 driver[1], for numbers on
  stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
  frequency to 80MHz` commit message]

1. https://github.com/openwrt/openwrt/pull/1578

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:46 +01:00
Rosen Penev
274439b780 ramips: Increase GB-PC2 SPI frequency to 80MHz
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.

>From testing this, higher values do not improve speeds.

time dd if=/dev/mtdblock3 of=/dev/null bs=64k from

42.82s to 14.09s.

boot speed is also faster:
[   66.884087] procd: - init - vs
[   48.976049] procd: - init -

Since spi speed was requested:
[    3.538884] spi-mt7621 1e000b00.spi: sys_freq: 225000000

CPU is 900MHz:
[    0.000000] CPU Clock: 900MHz

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 09:01:23 +01:00
David Bauer
3f019bf96c ramips: add Netgear EX6150
SoC:   MediaTek MT7621
RAM:   64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi:  MediaTek MT7662E bgn 2SS
WiFi:  MediaTek MT7662E nac 2SS
BTN:   ON/OFF - Reset - WPS - AP/Extender toggle
LED:    - Arrow Right (blue)
        - Arrow Left (blue)
        - WiFi 1 (red/green)
        - WiFi 2 (red/green)
        - Power (green/amber)
        - WPS (Green)
UART:  UART is present as Pads on the backside of the PCB. They are
       located on the other side of the Ethernet port.
       3.3V - GND - TX - RX / 57600-8N1
       3.3V is the nearest one to the antenna connectors

Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).

You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash

Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Vladimir Kot
58becdb30d ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button

Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
   to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Tobias Welz
7c4b85ee27 ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.

SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)

Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1).  Then get the
sysupgrade image from a tftp server.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:33:59 +00:00
Koen Vandeputte
af6c86dbe5 kernel: bump 4.14 to 4.14.108
Refreshed all patches.

Altered patches:
- 950-0033-i2c-bcm2835-Add-debug-support.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-27 10:48:59 +01:00
Felix Fietkau
bee7ff7cf3 ramips: allow packets with ttl=0
Some broken ISPs (e.g. Comcast) send DHCPv6 packets with hop limit=0.
This trips up the TTL=0 check in the PPE if enabled.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-03-24 12:10:15 +01:00