The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 V7.5 @ 320Mhz
- RAM: 64 MB DDR2
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard)
- USB: 1x 2.0
- Buttons: 2x
- ADSL: yes, unsupported
- LEDs: 7x
- UART: yes
Installation via CFE web UI:
1. Power off the router and press the RESET button
2. Power on the router and wait 12 or more seconds
3. Release the RESET button
4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The data RAC is left disabled by the bootloader in some SoCs, at least in
the core it boots from. Enabling this feature increases the performance up
to +30% depending on the task.
The kernel enables the whole RAC unconditionally on BMIPS3300 CPUs. Enable
the data RAC in a similar way also for BMIPS4350.
Tested on DGND3700 v1 (BCM6368) and HG556a (BCM6358).
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
In pushing and refreshing 6.1 pull request, dbac8e8819 ("ipq806x: 6.1:
copy patches, files and config from 5.15") wasn't correctly updated and
resulted in missing the dts for Netgear XR450. This caused compilation
error with Netgear R7800 or XR500 if testing kernel version was used.
Fix this by adding back the missing dts for Netgear XR450 from kernel
5.15.
Fixes: dbac8e8819 ("ipq806x: 6.1: copy patches, files and config from 5.15")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Critical thermal trips patch got merged upstream, so use the upstreamed
patch and mark it as backport along with the future 6.5 kernel version.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Without it the WAN port won't be initialized properly.
Fixes: 8f578c15b3 ("rockchip: add NanoPi R2C support")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Currently, Compex WPQ873 images are not including the ath11k BDF-s at all
and this means that there is no WLAN support, so lets include the BDF as
its already packaged.
Fixes: 07c45c0859 ("ipq807x: add support for Compex WPQ873")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move default cpufreq governor from ONDEMAND to PERFORMANCE. The temp
increase is just 2°C and Watt usage the change is minimal in the order
of additional millwatt. The SoC and krait in general looks to suffer for
some problem with cache scaling. To have better system stability, force
cpu freq and cache freq to the max value supported by the system. This
follows mvebu platform where cpufreq is broken and cause minimal
temp/watt increase.
User can still tweak the governor to ondemand using sysfs entry if
needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.
This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.
This is a preparation for later addition of IPQ60xx and IPQ50xx support.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, ipq807x only covers Qualcomm IPQ807x SoC-s.
However, Qualcomm also has IPQ60xx and IPQ50xx SoC-s under the AX WiSoC-s
and they share a lot of stuff with IPQ807x, especially IPQ60xx so to avoid
duplicating kernel patches and everything lets make a common target with
per SoC subtargets.
Start doing that by renaming ipq807x to qualcommax so that dependencies
on ipq807x target can be updated.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we build also core packages, we need more host tools. Compile
all of them to reduce compile time on other actions.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Power LED register is wrong at dts. Fix it.
Fixes: 9ceeaf4c6c ("brcm63xx: switch to hardware led controllers")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM63169
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 128 MB DDR
- Flash: 128 MB NAND
- LAN switch: Broadcom BCM53125, 5x 1Gbit
- Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 2x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
All switch ports are labeled as port@address so let's follow the same pattern.
Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (v1) / 128 MB (v2) DDR
- Flash: 128 MB NAND
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
- USB: 1x 2.0
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is needed on devices like Sercomm AD1018 for booting recent kernels due
to bigger kernels.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Maintaining bcm63xx is a nightmare due to the amount of devices and patches
required, since every board requires an individual patch due to the lack of
full device tree compatibility.
Moreover, there are a lot of devices supported on this target which won't work
due to not having enough resources (16M-32M of RAM and/or 4M of flash).
Therefore, any development efforts should be focused on bmips and support for
those devices with enough resources should be added on bmips target.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.
Hardware:
- SoC: Broadcom BCM6368
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 32 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 1x 2.0
- Buttons: 2x, 1 reset
- LEDs: 7x
- UART: yes
The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.
Installation via CFE web UI:
1. Connect the UART serial port.
2. Power on the router and press enter at the console prompt to stop the
bootloader.
4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bcm63xx.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bmips.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some Broadcom MIPS devices require JFFS2 cleanmarkers to be present on the
kernel partition or the bootloader will identify the partition as corrupt and
won't boot the kernel.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The DGND3700v2 renames the cferam bootloader from cferam to cfeXXX, where XXX
is the number of firmware upgrades performed by the bootloader. Other bcm63xx
devices rename cferam.000 to cferam.XXX, but this device is special because
the cferam name isn't changed on the first firmware flashing but it's changed
on the subsequent ones.
Therefore, we need to look for "cfe" instead of "cferam" to properly detect
the cferam partition and fix the bootlop.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices rename cferam bootloader using specific patterns and don't follow
broadcom standards for renaming cferam files. This requires supporting
different cferam file names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
openssl sets additional cflags in its configuration script. We need to
make it aware of our custom cflags to avoid adding conflicting cflags.
Fixes: #12866
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
Backport patches improving ppp interface creation. As a side effect this
also fix a bug from using netdev trigger that suffer from LED state
wrongly set due to using old ioctl for ppp creation.
Tested-by: Csaba Sipos <metro4@freemail.hu>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch initially introduced in 94b4da9b4a
breaks mvebu devices when using vlan filtering with kernel 5.15 or 6.1,
it was working ok in 5.10.
With this patch, frame that should exit untagged from the switch exit tagged.
Running 'tcpdump -Q out -evnnli eth1' (eth1 being the dsa interface)
- with the hack, frame is sent directly to the
destination port 4 with VID 2, so the switch leave the tag as instructed:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode From CPU, target dev 0, port 4, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
- without the hack, frame is sent to the switch that
performs the forwarding decision and untagging:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode Forward, dev 1, port 0, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
Removing this patch makes my Turris Omnia usable with vlan filtering,
ie wifi device can talk to wired device again.
Using kernel 5.15 some broadcast/multicast traffic is still leaked
(on a VLAN 2 access port I see tagged VLAN 3 frame),
using kernel 6.1 fixes that.
People needing the extra performance should try the bridger package.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB DDR
- Flash: 16 MB SPI NOR
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn
- USB: 1x 2.0
- Buttons: 1x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This was done by executing these commands:
$ ./scripts/kconfig.pl '+' target/linux/generic/config-6.1 /dev/null > target/linux/generic/config-6.1-new
$ mv target/linux/generic/config-6.1-new target/linux/generic/config-6.1
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This ports the TP-Link TL-WDR6500 v2 from ar71xx to ath79.
Specifications:
SoC: QCA9561
CPU: 750 MHz
Flash: 8 MiB (Winbond W25Q64FVSIG)
RAM: 128 MiB
WiFi 2.4 GHz: QCA956X 3x3 MIMO 802.11b/g/n
WiFi 5 GHz: QCA9882-BR4A 2x2 MIMO 802.11a/n/ac
Ethernet: 4x LAN and 1x WAN (all 100M)
USB: 1x Header
Flashing instructions:
As it appears, the device does not support flashing via GUI or
TFTP, only serial is possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Xiaobing Luo <luoxiaobing0926@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the repository
link to the new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
source.codeaurora.org project has been shut down and the nxp
repositories has been moved to github. Update the link reference to the
new location.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 64 MB DDR
- Flash: 8 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
If dual-stack configuration is in use, and dhcpv6 option is set, do not start
464xlat sub-interface for dhcpv6 sub-interace , as the configuration already
provides IPv4 connectivty, be it through single or dual APN configuration.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Add two new "v6apn" and "v6profile" properties, to support split-APN
dual-stack onfiguration. This extends the existing ipv4v6 PDP type,
allowing simultaneous connection to two distinct APNs,
one for IPv4 and one for IPv6.
The parameters override existing 'apn' and 'profile' respectively,
if set, but only for IPv6 part of the connection.
If unset, they default to their original values, constituting a standard
IPv4v6 setup.
If a different APN is set for IPv6, a corresponding profile MUST also be
configured, with a different ID, than the IPv4 profile, for example,
profile 2.
Both APNs must match ones configured through QMI or through 'AT+CGDCONT'
command.
Example configuration in UCI:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option autoconnect '1'
option pdptype 'ipv4v6'
option apn 'internet'
option v6apn 'internetipv6'
option profile '1'
option v6profile '2'
Corresponding profile configuration:
AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV6","internetipv6","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
