The GW82xx-2x has two network ports. By convention, the first
port (eth0) should be the WAN port and the second port (eth1)
should be the LAN port.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17717
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d2eaaa90d502fa418d7d9bb8d4e6ccbe0131c832)
The act of attempting link at gen1 then trying to link at higher speeds
causes a hang with the specific PCIe switch used on the Gateworks Venice
boards. Work around this by linking at the highest speed first as is
common with all other PCI controller drivers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17717
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 23a18a57cf750d9081353cdd34e44982ea10e191)
Add several dt backports for the Gateworks Venice product family.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17717
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1ce87cf25c19f030b81954639545db2ab7f17062)
Add a backport of a btsdio patch for the cyw437 bluetooth controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17717
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c9f11523dd5b8639b24b97043d70f2a197a00a84)
This commit fixes nmbm configuration mismatch error on Xiaomi AX3000t
with Winbond W25N01KVZEIR spi-nand:
'''
[ 0.786783] NMBM configuration mismatch
'''
Root cause:
1. U-Boot W25N01KV spi-nand driver ia compiled with 64B OOB size for the
chip and store this size in the nmbm signature;
2. Linux W25N01KV driver use 96B OOB.
The change doesn't affect AX3000t variants with other spi-nand chips
(ESMT, Foresee) because their Linux drivers use 64B OOB.
Fixes: openwrt#16972
Tested-by: Aleksandr Danilov <sc16me@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3299d19c01080c3320e3ff6964d7825da81bb8b4)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds new "mediatek,bmt-mtd-overridden-oobsize" property. The
property helps avoid "NMBM configuration mismatch" error if mtd "OOB size"
is not equal to the "spare size" which is stored in the nmbm signature.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e585ae70d4f2a563b3b0e430e15ee19ad25caeb5)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b11bff90f2ad r8169: add support for RTL8125BP rev.b
b3593df26ab1 r8169: add support for RTL8125D rev.b
b299ea006928 r8169: adjust version numbering for RTL8126
bb18265c3aba r8169: remove support for chip version 11
2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
The EEE advertisement patch has been reworked for linux v6.6 because
phy_set_eee_broken() is only present on linux >= v6.13 and eee_broken_modes
declaration has been converted to a bitmap, so linkmode_set_bit() can't be
used either.
e340bff27eed623fb8e3721aa69e70
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 084618f8db7d0e413b47bab3e0ea70804bf84ee2)
This reverts commit 3295f6f1c254cd7e5e5285a05581bf6abbde8999.
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
Fixes: #17818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f628467dfd6b32ead172d33a2593f04901395343)
Fix broken WAN on Linksys EAX and Asrock G10 by incrementing the WAN
interface MAC address + 1. This caused conflicting entry in the FDB
table and caused the WAN port to malfunction with the DSA conversion.
Fixes: #17157Fixes: #15585Fixes: #16604
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eba2fbf63814bbcf8c99c98177818476fca808a7)
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 69890e16b37d59b55ba64633522c727f957cb2fd)
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c87a767801ef375feadb0a5c41d5a674ad3a7d2c)
Link: https://github.com/openwrt/openwrt/pull/17790
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add kmod-drm-i915 to the default packages. It was build into the kernel
before and is now build as a kernel module.
Fixes: 77cfe8fd15d3 ("x86: make i915 as a kmod with required firmware")
Link: https://github.com/openwrt/openwrt/pull/17781
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8390599c9a29dbb0019447df9086cb8667bfd3d7)
Link: https://github.com/openwrt/openwrt/pull/17792
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt76x8 SDXC pin register definition is incompatible with the
mtmips generic pinctrl driver structure. This hack allows us to
mux the SDXC IO to different pin groups in device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
(cherry picked from commit 05ec3b50a8e673786dda0224b23f18b5d96a4a65)
Link: https://github.com/openwrt/openwrt/pull/17754
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The definition for the netgear_wndr4700 had two different
DEVICE_COMPAT_VERSION definitions.
In commit 5815884c3a2 ("apm821xx: migrate to DSA"), an additional
DEVICE_COMPAT_VERSION := 3.0 attribute was added to the device
definition. The old one with version 2.0 stayed and was defined later
overwriting the new one.
Replace the old version 2.0 with the new version 3.0
Fixes: 5815884c3a2a ("apm821xx: migrate to DSA")
Link: https://forum.openwrt.org/t/openwrt-24-10-0-rc6-sixth-release-candidate/222466/43
Link: https://github.com/openwrt/openwrt/pull/17741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dab52c00d712a421d6e61eebc51359e5d38ad347)
The STM32MP135F-DK board uses the LAN8742 PHY.
Enable CONFIG_SMSC_PHY to have full PHY support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17745
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d981f28f762a559ae50386fa089b050aaaa78555)
Since commit f1c9afd80138 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd80138 for USW-Flex restores full 1 Gbps switching
performance on all ports.
Signed-off-by: Anders Melchiorsen <amelchio@nogoto.net>
Link: https://github.com/openwrt/openwrt/pull/17703
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 62872f8bfd5c8bc80bb014417c6ed8057bbeb773)
Replace clock patch for eMMC with upstream version to add the tag and
flag them as upstreamed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a9b408a97f7bf8b1f98f355fefe3c9bfc959d5a6)
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b7edf88b0fe15b32be802c7de54036ff8e66dcc1)
Refresh cpufreq with merged upstream version. Also fix the PM Domain
rebased patch to correctly expose the symbol for non Mediatek target.
Update dtsi with new pm domain name.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fbbfcbf150cd7c72f49c149e7f9b9f4d0bf43e4b)
The on-device board name reported by 'ubus call system board' is not present
in the generated profiles.json. This results in upgrade tools being unable
to match the image with the proper device. Let's add a 'SUPPORTED_DEVICES'
entry for the board name to fix this.
Links: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/441
Links: 2a07270180
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17736
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7165937c3b6ebe5ac692fcde1cc69ba1c7a3d9c9)
Fix usage of non-existent 'caldata_patch_mac' function
by using the 'caldata_patch_data' function.
Fixes: #17734
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17737
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3295f6f1c254cd7e5e5285a05581bf6abbde8999)
Import patch "net: phy: realtek: mark existing MMDs as present"
When using Clause-45 mode to access RealTek RTL8221B 2.5G PHYs some
versions of the PHY fail to report the MMDs present on the PHY.
Mark MMDs PMAPMD, PCS and AN which are always existing according to
the datasheet as present to fix that.
Fixes: #16823, #17183, #17232
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
(cherry picked from commit 730db6b893748517949b1d3a0c0cb8b6c1288040)
Fixes typo for led properties.
Delete the unused rfb compatible.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 64d1b1089c25d778f5f22bfc0c1590a2e83b664e)
Use white led when running, consistent with the stock firmware.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 87632219d4b8f0c96ea053e375f6f324fab0806f)
Fixed interrupt support for 2.5G PHY.
Removed useless phy-mode on phy node.
Tested on Cudy TR3000.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 82b69dfaf6ca92eeffb7523295d3d81a1d54323a)
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Move the nmbm properties outside the partition definition.
Change uppercase to lowercase, add missing read-only flag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit ab375a3484db67857450ced461498ad3d7942e05)
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
CC: John Crispin <john@phrozen.org>
Fixes: cfd42a0098 ("ipq40xx: add Intel/Lantiq ATM hacks")
Suggested-by: Andre Heider <a.heider@gmail.com>
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-4-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6d6dc3a3c967174598a44503f4af281574660356)
the wifi leds of the wax206 were not reacting.
This patch enables the green leds to show activity, as the blue ones are very bright.
Also set the label-mac to the gmac0
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9ada8578fd2768d077607b189987972ad600a804)
Supported devices are listed in the metadata as the first part of the
DTS compatible. This normally follows the format "vendor,device".
When updating the device name of the 180W 1920-8G PoE an underscore was
used, instead of a comma, to join the vendor and device name. This will
lead to warnings for users wanting to sysupgrade a device with an older
compatible, as the device's info does not match the one the metadata.
Fixes: 987c96e88927 ("realtek: rename hpe,1920-8g-poe to match hardware")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 6a7fa68569ac11bb2c2abb14026e8b84acd3a12f)
Fixed an issue where both WAN LEDs light up before plugging in the
ethernet cable and no blinking regardless of WAN network activity.
Updated the LED configuration to reflect proper status:
Green indicates 2.5Gb connection speed.
Yellow indicates other connection speed and traffic activity.
This resolves inconsistent WAN LED behavior on Spectrum SAX1V1K routers.
Signed-off-by: Ivan Deng <hongba@rocketmail.com>
Link: https://github.com/openwrt/openwrt/pull/17623
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8e78bc39a38d2a82818bcae467d3bcbbbe8531f3)
This patch has been accepted for linux v6.14 so we can move it from pending
to backport.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 2f2e21a52bdfdcf83868e3169768fda134aa883b)
These patches have been accepted in linux v6.14 instead of v6.13.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 12a07e934c013c87ea96ddda8ec18c9af0362c53)
Expose the temperature sensor built-into RTL822x 2.5G and 5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 3a189e38317e3390ba5b17523f55bd2fb1b72327)
Refresh hack patches with make target/linux/refresh.
Fixes: 9508ca44eb57 ("kernel: backport improvement to page pool fragment handling from 6.7")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit ee730a66e9c670ec2ee37ee2b207accd539e1d15)
Makes it easier to keep drivers like mt76 in sync with newer versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9508ca44eb577a13e795e0a6c5683689efc61475)
(cherry picked from commit 478041997f068c87c6356108cf3dc3b667666dd5)
1. Import pending patch to fix ramips/mt7621 64MB targets.
2. Do not enable CONFIG_PAGE_POOL_STATS by default.
Signed-off-by: Danila Romanov <pervokur@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 15887235c1e3b732d4c8e14afac253d00a7bfb36)
Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.
Fixes: 1d49310fdb5e ("ath79: add Cisco Meraki MR18")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17680
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7423e67e1b8c7e4c9f527d1300dbeaab72b1f95f)
This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users:
Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.
RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function
RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call
I didn't find opened issue for AX3000t. Similar AX3200 issue:
Link: https://github.com/openwrt/openwrt/issues/16347
So, other Xiaomi devices (e.g. Xiaomi WR30U) may also require fix.
Fixes: 7dbcc1215a56cc1da68c81bf92d7efa174c5e051 ("mediatek: filogic: add support for Xiaomi AX3000T")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 42a253c7e8992e2274628b1770a0263ac433d0bc)
This commit replaces multiple fw_setenv calls by the bulk one to reduce
flash writes.
Thanks @Linaro1985 for the idea.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a6b0abf4661e4dc1449494e46340f75c44df81de)
the CWMP account mac is correctly set on the lan device but was not correctly as label-mac
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f9813f41b2e9fccb644ae149eabe575fbae12fa3)
Devices with wifi (LicheePi RV and MangoPi MQ Pro) were using the
wrong module. Also wpad was missing to enable using the WiFi.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/17576
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
(cherry picked from commit 8a17bae722a62954269f29dc48025e88c919dc24)
The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before.
This commit changes this to trigger on activity of the respective radio
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17627
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 99431e315039d7f9689b21a8aa220adadf52a886)
Now that LZMA_TEXT_START is configurable per-target once again,
move the target above 32MB boundary for ZTE MF28* devices.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 32c6b9064ac7fc62cead37b1bc7d46ffba598c71)
initramfs for some devices grew so big, that it can't be loaded within
the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable
per-target once again, to fix it for bigger devices, while maintaining
compatibility with previous ones.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6720958659d226e71dca49657202e0502bb059bd)
Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3d63a41ffab69cb6f49c14cff99c3c3a84899363)
This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.
This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).
In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.
However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2cac2a9785ada7c30388349f5d9a9bdcff2e730)
