The current CFLAGS (rv64imafdc) for the riscv64 targets do not contain
the full generic compute extension (g), as that also includes the
zicsr and zifencei extensions/instructions. Rename the default ISA to
'generic' to add distinction to the current binaries (although it's very
minimal), and use rv64gc for CFLAGS.
This is also a prep step for the upcoming gcv (vector-extension supporting)
targets like the Spacemit K1, and the thead-cores like the TH1520.
Compile-tested: all riscv64 targets
Runtime-tested:
- SiFive Unleashed (FU540)
- SiFive Unmatched (FU740)
- Nezha D1 (D1)
- VisionFive2 (JH7110)
Link: https://github.com/openwrt/openwrt/pull/18094
Tested-by: Chuanhong Guo <gch981213@gmail.com> # siflower target
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Do not assume that the various tools like llc can be found under the
same path as clang; instead, look them up through BPF_PATH (while still
preferring ones found next to clang).
This fixes build in common setups with ccache, where clang resolves to a
path like /usr/lib/ccache/bin/clang, but no other tools can be found at
that location.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18422
Signed-off-by: Robert Marko <robimarko@gmail.com>
CLANG_MIN_VER is 12, so there is no point in looking for clang-11.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18422
Signed-off-by: Robert Marko <robimarko@gmail.com>
TF-A LTS releases have an lts- prefix in their version tag. Introduce a
PKG_LTS variable to support these.
As the non-LTS tarbals do not contain the version prefix in the
directory, we need different PKG_BUILD_DIR for each variant:
➜ tar --list --file dl/trusted-firmware-a-v2.12.tar.gz | head -n1
trusted-firmware-a-2.12/
➜ tar --list --file dl/trusted-firmware-a-lts-v2.12.1.tar.gz | head -n1
trusted-firmware-a-lts-v2.12.1/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
kmod-leds-pwm depends on @PWM_SUPPORT, instead of adding pwm to the
features env for specific targets, use the existing detection method.
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be used by GL.iNet devices from other target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
In some cases hostpkg python from packages feed is used (hostpkg has higher
priority in PATH) which causes build failure (cryptography module is
missing). So override PATH to not use hostpkg python.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18102
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unless another toolchain is present (or selected), build the bpf toolchain
whenever a package is selected that needs it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The three packages base-files, libc and kernel are special, the former
can't be upgraded in place since it's content are modified on startup,
the latter two are virtual packages only used as constraints for the
package manager.
Historically base-files was "locked" via a special OPKG function, the
latter two were hidden from the package index and thereby never picked
as possible upgrade.
Time moved forward and we now have APK and tools like OWUT. The latter
compares available packages with installed packages and generates user
readable output, requiring versions for libc and kernel, too. At the
same time, APK uses a different looking mechanism, which is set during
installation instead of part of the package metadata.
In short, this patch adds version constraints to the three packages,
allowing them to be part of the package index.
Fixes: #17774Fixes: #17775Fixes: efahl/owut#31
Signed-off-by: Paul Spooren <mail@aparcar.org>
This new value points to where firmware can be downloaded. It's not
about a single release but all available firmware releases.
In the next step, this URL should be exposed via `ubus call system
board` as an entry of the `distribution` field. With that value, the
running firmware can check for newer releases.
We already have VERSION_REPO however that's different and only meant for
package managers to download their fitting package indexes/packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/17780
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is currently a problem where the rootfs in an initramfs image for
single target build is not updated on subsequent run. This is caused by
a bug introduced in d78dec3e19e3 ("kernel: copy kernel build dir on
Per-Device Initramfs compilation") where the initramfs_data.cpio rm was
moved to PrepareConfigPerRootfs. This caused the side effect of dropping
the rm call for single target build making the kernel reusing the
previous generated initramfs_data.cpio.
To correctly handle this, restore the original location of this call
right after the touch /init call. This way the kernel will always
regenerate the initramfs embedded rootfs ALSO for single target build.
Fixes: d78dec3e19e3 ("kernel: copy kernel build dir on Per-Device Initramfs compilation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
Strip off initial leading blanks and tabs from scripts and script
fragments that are supplied by the package's Makefile. Specifically,
the script included in the postrm must be left justified so that
the shebang is in the first column.
Fixes: https://github.com/openwrt/openwrt/issues/17439
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17440
Signed-off-by: Robert Marko <robimarko@gmail.com>
If CC is explicitly set to a non default value, TF-A keeps this value.
Otherwise it assigns generic default value.
As the build bot set CC=/usr/bin/gcc-10, TF-A uses it which causes a
compile issue.
So unset CC before compiling.
It's a new behavior since v2.12. A part of the explanation is available in
this commit [1].
[1] e01c71266f
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17465
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since v2.12, TF-A automatically selects the no-warn-rwx-segments option if
needed.
So move this hack to the package Makefiles.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17243
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.65
Update to checksum only/no patches required a rebase.
Per the changelog, this is a trivial upstream bump with only 4
commits, 2 of which being reverts.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17217
Signed-off-by: Robert Marko <robimarko@gmail.com>
mkits.sh creates a root.*.pagesync file with padding, which is global, and
the generated .its files reference it. Since dtc reads this file, it must
not run at the same time as mkits.sh
Fixes generating itb images with broken rootfs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Fixes: #17146
Link: https://github.com/openwrt/openwrt/pull/17151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce package flag MESON_USE_STAGING_PYTHON which allows packages
to be built with the OpenWrt-built python3/host instead of relying on the
buildhost's Python distribution.
This is useful for packages using Meson which require additional Python
modules during build.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, in case when a package in the device package list is marked with
the "-"" prefix meaning that its supposed to be removed for that device but
it was not actually previously built it will cause the APK to error out it
and thus image generation will also fail.
So, lets do what OPKG build step does and supress the error with the "-"
prefix in make.
Fixes: #17103
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17106
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is required for upcoming Keenetic KN-3911 support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set MESON_ARGS and MESON_HOST_ARGS when calling ninja for building.
This is required eg. to be able to set PYTHONPATH= not just for the
Meson (==configure) run but also for the build phase itself.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
