mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-18 21:28:02 +00:00
mediatek: filogic: Add support for D-Link AQUILA PRO AI M60
Specification: - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX) - MT7531 switch - 512MB RAM - 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size - 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1) - 3 buttons (WPS, reset, LED on/off) - 1x 2.5 Gbit WAN port with Maxlinear GPY211C - 4x 1 Gbit LAN ports Disassembly: - There are five screws at the bottom: 2 under the rubber feet, 3 under the label. - After removing the screws, the white plastic part can be shifted out of the blue part. - Be careful because the antennas are mounted on the side and the top of the white part. Serial Interface - The serial interface can be connected to the 4 pin holes next to/under the antenna cables. - Note that there is another set of 4 pin holes on the side of the board, it's not used. - Pins (from front to rear): - 3.3V (do not connect) - TX - RX - GND - Settings: 115200, 8N1 MAC addresses: - MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52) - MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53) - WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52) - LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53) - WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54) - WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57) Flashing via OEM web interface: - Currently not supported because image crypto is not known Flashing via recovery web interface: - Currently not supported because recovery image format is not known (differs from M30) - Recovery web interface is accessible via 192.168.200.1 after pressing the reset button during start of the device Flashing via Initramfs: - Open router, connect serial interface - Start a TFTP server at 192.168.200.2 and provide the initramfs image there - When starting the router, select "7. Load Image" in U-Boot - Settings for load address, load method can be kept as they are - Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2) - Enter the file name of the initramfs image - Confirm "Run loaded data now?" question after loading the image with "Y" - OpenWrt initramfs will start now - Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM - Check the active boot partition settings by running fw_printenv, the following variables should be set for booting from the ubi partition: - bootpart=0 - sw_tryactive=2 - sw_active=1 - If the variables are not set as expected, OEM firmware is running on the ubi1 partition. Change the settings accordingly: - fw_setenv sw_tryactive 0 - Flash sysupgrade image to flash - After first OpenWrt boot from flash, OpenWrt will set the U-Boot variables accordingly (must not be done manually): - bootpart=0 - sw_tryactive=2 - sw_active=1 Reverting back to OEM: - Boot the initramfs image as described in "Flashing via Initramfs" above - Copy the backed up ubi partition to /tmp (e.g. by using SCP) - Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4 - Reboot the device, OEM firmware will start now Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
This commit is contained in:
Roland Reinl
parent
03560d470c
commit
d513185d7f
@ -96,7 +96,8 @@ zbtlink,zbt-z8102ax|\
|
||||
zbtlink,zbt-z8103ax)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
|
||||
;;
|
||||
dlink,aquila-pro-ai-m30-a1)
|
||||
dlink,aquila-pro-ai-m30-a1|\
|
||||
dlink,aquila-pro-ai-m60-a1)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x40000"
|
||||
;;
|
||||
gatonetworks,gdsp)
|
||||
|
||||
377
target/linux/mediatek/dts/mt7986a-dlink-aquila-pro-ai-m60-a1.dts
Normal file
377
target/linux/mediatek/dts/mt7986a-dlink-aquila-pro-ai-m60-a1.dts
Normal file
@ -0,0 +1,377 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "mt7986a.dtsi"
|
||||
|
||||
/ {
|
||||
model = "D-Link AQUILA PRO AI M60 A1";
|
||||
compatible = "dlink,aquila-pro-ai-m60-a1", "mediatek,mt7986a";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &led_status_white;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_white;
|
||||
led-upgrade = &led_status_blue;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@40000000 {
|
||||
reg = <0 0x40000000 0 0x20000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
button-wps {
|
||||
label = "wps";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
button-leds-on-off {
|
||||
label = "leds-on-off";
|
||||
linux,code = <KEY_LIGHTS_TOGGLE>;
|
||||
gpios = <&pio 47 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cells = <&macaddr_odm 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "2500base-x";
|
||||
phy-handle = <&phy6>;
|
||||
nvmem-cells = <&macaddr_odm 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
label = "internet";
|
||||
};
|
||||
|
||||
mdio: mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <1500000>;
|
||||
reset-post-delay-us = <1000000>;
|
||||
|
||||
phy6: phy@6 {
|
||||
compatible = "maxlinear,gpy211", "ethernet-phy-ieee802.3-c45";
|
||||
reg = <6>;
|
||||
phy-mode = "2500base-x";
|
||||
};
|
||||
|
||||
switch@1f {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan4";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi_flash_pins: spi-flash-pins-33-to-38 {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
conf-pu {
|
||||
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-up-adv = <0>; /* bias-disable */
|
||||
};
|
||||
conf-pd {
|
||||
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
|
||||
drive-strength = <8>;
|
||||
mediatek,pull-down-adv = <0>; /* bias-disable */
|
||||
};
|
||||
};
|
||||
|
||||
wf_2g_5g_pins: wf_2g_5g-pins {
|
||||
mux {
|
||||
function = "wifi";
|
||||
groups = "wf_2g", "wf_5g";
|
||||
};
|
||||
conf {
|
||||
pins =
|
||||
"WF0_HB2",
|
||||
"WF0_HB3",
|
||||
"WF0_HB4",
|
||||
"WF0_HB0",
|
||||
"WF0_HB0_B",
|
||||
"WF0_HB5",
|
||||
"WF0_HB6",
|
||||
"WF0_HB7",
|
||||
"WF0_HB8",
|
||||
"WF0_HB9",
|
||||
"WF0_HB10",
|
||||
"WF0_TOP_CLK",
|
||||
"WF0_TOP_DATA",
|
||||
"WF1_HB1",
|
||||
"WF1_HB2",
|
||||
"WF1_HB3",
|
||||
"WF1_HB4",
|
||||
"WF1_HB0",
|
||||
"WF1_HB5",
|
||||
"WF1_HB6",
|
||||
"WF1_HB7",
|
||||
"WF1_HB8",
|
||||
"WF1_TOP_CLK",
|
||||
"WF1_TOP_DATA";
|
||||
drive-strength = <4>;
|
||||
};
|
||||
};
|
||||
|
||||
i2c_pins_3_4: i2c-pins-3-4 {
|
||||
mux {
|
||||
function = "i2c";
|
||||
groups = "i2c";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "spi-nand";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <20000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x000000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x3200000>;
|
||||
};
|
||||
|
||||
partition@3780000 {
|
||||
label = "ubi1";
|
||||
reg = <0x3780000 0x3200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6980000 {
|
||||
label = "Odm";
|
||||
reg = <0x6980000 0x40000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_odm: macaddr@81 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x81 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
partition@69c0000 {
|
||||
label = "Config1";
|
||||
reg = <0x69c0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6a40000 {
|
||||
label = "Config2";
|
||||
reg = <0x6a40000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@6ac0000 {
|
||||
label = "Storage";
|
||||
reg = <0x6ac0000 0xA00000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&wf_2g_5g_pins>;
|
||||
|
||||
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
|
||||
band@0 {
|
||||
/* 2.4 GHz */
|
||||
reg = <0>;
|
||||
nvmem-cells = <&macaddr_odm 2>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
band@1 {
|
||||
/* 5 GHz */
|
||||
reg = <1>;
|
||||
nvmem-cells = <&macaddr_odm 5>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c_pins_3_4>;
|
||||
|
||||
gca230718@40 {
|
||||
compatible = "unknown,gca230718";
|
||||
reg = <0x40>;
|
||||
|
||||
led_status_red: led@0 {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
led@1 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
led_status_blue: led@2 {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
led_status_white: led@3 {
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
function = LED_FUNCTION_STATUS;
|
||||
reg = <3>;
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -89,7 +89,8 @@ mediatek_setup_interfaces()
|
||||
openwrt,one)
|
||||
ucidef_set_interfaces_lan_wan eth1 eth0
|
||||
;;
|
||||
dlink,aquila-pro-ai-m30-a1)
|
||||
dlink,aquila-pro-ai-m30-a1|\
|
||||
dlink,aquila-pro-ai-m60-a1)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet
|
||||
;;
|
||||
keenetic,kn-3911|\
|
||||
|
||||
@ -12,6 +12,11 @@ boot() {
|
||||
fw_setenv bootpart 1
|
||||
fi
|
||||
;;
|
||||
dlink,aquila-pro-ai-m60-a1)
|
||||
fw_setenv bootpart 0
|
||||
fw_setenv sw_active 1
|
||||
fw_setenv sw_tryactive 2
|
||||
;;
|
||||
zyxel,ex5700-telenor)
|
||||
fw_setenv uboot_bootcount 0
|
||||
;;
|
||||
|
||||
@ -701,6 +701,18 @@ define Device/dlink_aquila-pro-ai-m30-a1
|
||||
endef
|
||||
TARGET_DEVICES += dlink_aquila-pro-ai-m30-a1
|
||||
|
||||
define Device/dlink_aquila-pro-ai-m60-a1
|
||||
DEVICE_VENDOR := D-Link
|
||||
DEVICE_MODEL := AQUILA PRO AI M60
|
||||
DEVICE_VARIANT := A1
|
||||
DEVICE_DTS := mt7986a-dlink-aquila-pro-ai-m60-a1
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-leds-gca230718 kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware
|
||||
IMAGE_SIZE := 51200k
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += dlink_aquila-pro-ai-m60-a1
|
||||
|
||||
define Device/edgecore_eap111
|
||||
DEVICE_VENDOR := Edgecore
|
||||
DEVICE_MODEL := EAP111
|
||||
|
||||
Loading…
Reference in New Issue
Block a user