From d513185d7f4dde0adc51c43aa7577a0a1529ea93 Mon Sep 17 00:00:00 2001 From: Roland Reinl Date: Fri, 13 Dec 2024 18:58:26 +0100 Subject: [PATCH] mediatek: filogic: Add support for D-Link AQUILA PRO AI M60 Specification: - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX) - MT7531 switch - 512MB RAM - 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size - 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1) - 3 buttons (WPS, reset, LED on/off) - 1x 2.5 Gbit WAN port with Maxlinear GPY211C - 4x 1 Gbit LAN ports Disassembly: - There are five screws at the bottom: 2 under the rubber feet, 3 under the label. - After removing the screws, the white plastic part can be shifted out of the blue part. - Be careful because the antennas are mounted on the side and the top of the white part. Serial Interface - The serial interface can be connected to the 4 pin holes next to/under the antenna cables. - Note that there is another set of 4 pin holes on the side of the board, it's not used. - Pins (from front to rear): - 3.3V (do not connect) - TX - RX - GND - Settings: 115200, 8N1 MAC addresses: - MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52) - MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53) - WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52) - LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53) - WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54) - WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57) Flashing via OEM web interface: - Currently not supported because image crypto is not known Flashing via recovery web interface: - Currently not supported because recovery image format is not known (differs from M30) - Recovery web interface is accessible via 192.168.200.1 after pressing the reset button during start of the device Flashing via Initramfs: - Open router, connect serial interface - Start a TFTP server at 192.168.200.2 and provide the initramfs image there - When starting the router, select "7. Load Image" in U-Boot - Settings for load address, load method can be kept as they are - Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2) - Enter the file name of the initramfs image - Confirm "Run loaded data now?" question after loading the image with "Y" - OpenWrt initramfs will start now - Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM - Check the active boot partition settings by running fw_printenv, the following variables should be set for booting from the ubi partition: - bootpart=0 - sw_tryactive=2 - sw_active=1 - If the variables are not set as expected, OEM firmware is running on the ubi1 partition. Change the settings accordingly: - fw_setenv sw_tryactive 0 - Flash sysupgrade image to flash - After first OpenWrt boot from flash, OpenWrt will set the U-Boot variables accordingly (must not be done manually): - bootpart=0 - sw_tryactive=2 - sw_active=1 Reverting back to OEM: - Boot the initramfs image as described in "Flashing via Initramfs" above - Copy the backed up ubi partition to /tmp (e.g. by using SCP) - Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4 - Reboot the device, OEM firmware will start now Signed-off-by: Roland Reinl --- .../uboot-envtools/files/mediatek_filogic | 3 +- .../mt7986a-dlink-aquila-pro-ai-m60-a1.dts | 377 ++++++++++++++++++ .../filogic/base-files/etc/board.d/02_network | 3 +- .../filogic/base-files/etc/init.d/bootcount | 5 + target/linux/mediatek/image/filogic.mk | 12 + 5 files changed, 398 insertions(+), 2 deletions(-) create mode 100644 target/linux/mediatek/dts/mt7986a-dlink-aquila-pro-ai-m60-a1.dts diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index d0a15e34736..022e78952d4 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -96,7 +96,8 @@ zbtlink,zbt-z8102ax|\ zbtlink,zbt-z8103ax) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" ;; -dlink,aquila-pro-ai-m30-a1) +dlink,aquila-pro-ai-m30-a1|\ +dlink,aquila-pro-ai-m60-a1) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x40000" ;; gatonetworks,gdsp) diff --git a/target/linux/mediatek/dts/mt7986a-dlink-aquila-pro-ai-m60-a1.dts b/target/linux/mediatek/dts/mt7986a-dlink-aquila-pro-ai-m60-a1.dts new file mode 100644 index 00000000000..a95c069156e --- /dev/null +++ b/target/linux/mediatek/dts/mt7986a-dlink-aquila-pro-ai-m60-a1.dts @@ -0,0 +1,377 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; +#include +#include +#include + +#include "mt7986a.dtsi" + +/ { + model = "D-Link AQUILA PRO AI M60 A1"; + compatible = "dlink,aquila-pro-ai-m60-a1", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + led-boot = &led_status_white; + led-failsafe = &led_status_red; + led-running = &led_status_white; + led-upgrade = &led_status_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@40000000 { + reg = <0 0x40000000 0 0x20000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + button-wps { + label = "wps"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + button-leds-on-off { + label = "leds-on-off"; + linux,code = ; + gpios = <&pio 47 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cells = <&macaddr_odm 1>; + nvmem-cell-names = "mac-address"; + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy-handle = <&phy6>; + nvmem-cells = <&macaddr_odm 0>; + nvmem-cell-names = "mac-address"; + label = "internet"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <1500000>; + reset-post-delay-us = <1000000>; + + phy6: phy@6 { + compatible = "maxlinear,gpy211", "ethernet-phy-ieee802.3-c45"; + reg = <6>; + phy-mode = "2500base-x"; + }; + + switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <66 IRQ_TYPE_LEVEL_HIGH>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = + "WF0_HB2", + "WF0_HB3", + "WF0_HB4", + "WF0_HB0", + "WF0_HB0_B", + "WF0_HB5", + "WF0_HB6", + "WF0_HB7", + "WF0_HB8", + "WF0_HB9", + "WF0_HB10", + "WF0_TOP_CLK", + "WF0_TOP_DATA", + "WF1_HB1", + "WF1_HB2", + "WF1_HB3", + "WF1_HB4", + "WF1_HB0", + "WF1_HB5", + "WF1_HB6", + "WF1_HB7", + "WF1_HB8", + "WF1_TOP_CLK", + "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + i2c_pins_3_4: i2c-pins-3-4 { + mux { + function = "i2c"; + groups = "i2c"; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <20000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x3200000>; + }; + + partition@3780000 { + label = "ubi1"; + reg = <0x3780000 0x3200000>; + read-only; + }; + + partition@6980000 { + label = "Odm"; + reg = <0x6980000 0x40000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_odm: macaddr@81 { + compatible = "mac-base"; + reg = <0x81 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + + }; + + partition@69c0000 { + label = "Config1"; + reg = <0x69c0000 0x80000>; + read-only; + }; + + partition@6a40000 { + label = "Config2"; + reg = <0x6a40000 0x80000>; + read-only; + }; + + partition@6ac0000 { + label = "Storage"; + reg = <0x6ac0000 0xA00000>; + read-only; + }; + + }; + }; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; + + + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; + + band@0 { + /* 2.4 GHz */ + reg = <0>; + nvmem-cells = <&macaddr_odm 2>; + nvmem-cell-names = "mac-address"; + }; + band@1 { + /* 5 GHz */ + reg = <1>; + nvmem-cells = <&macaddr_odm 5>; + nvmem-cell-names = "mac-address"; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_3_4>; + + gca230718@40 { + compatible = "unknown,gca230718"; + reg = <0x40>; + + led_status_red: led@0 { + color = ; + function = LED_FUNCTION_STATUS; + reg = <0>; + }; + + led@1 { + color = ; + function = LED_FUNCTION_STATUS; + reg = <1>; + }; + + led_status_blue: led@2 { + color = ; + function = LED_FUNCTION_STATUS; + reg = <2>; + }; + + led_status_white: led@3 { + color = ; + function = LED_FUNCTION_STATUS; + reg = <3>; + }; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 2a133813263..4a95b4b7f37 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -89,7 +89,8 @@ mediatek_setup_interfaces() openwrt,one) ucidef_set_interfaces_lan_wan eth1 eth0 ;; - dlink,aquila-pro-ai-m30-a1) + dlink,aquila-pro-ai-m30-a1|\ + dlink,aquila-pro-ai-m60-a1) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet ;; keenetic,kn-3911|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/init.d/bootcount b/target/linux/mediatek/filogic/base-files/etc/init.d/bootcount index e186589f281..191f02984a7 100755 --- a/target/linux/mediatek/filogic/base-files/etc/init.d/bootcount +++ b/target/linux/mediatek/filogic/base-files/etc/init.d/bootcount @@ -12,6 +12,11 @@ boot() { fw_setenv bootpart 1 fi ;; + dlink,aquila-pro-ai-m60-a1) + fw_setenv bootpart 0 + fw_setenv sw_active 1 + fw_setenv sw_tryactive 2 + ;; zyxel,ex5700-telenor) fw_setenv uboot_bootcount 0 ;; diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 1fdb3036776..adaabd9acec 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -701,6 +701,18 @@ define Device/dlink_aquila-pro-ai-m30-a1 endef TARGET_DEVICES += dlink_aquila-pro-ai-m30-a1 +define Device/dlink_aquila-pro-ai-m60-a1 + DEVICE_VENDOR := D-Link + DEVICE_MODEL := AQUILA PRO AI M60 + DEVICE_VARIANT := A1 + DEVICE_DTS := mt7986a-dlink-aquila-pro-ai-m60-a1 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-leds-gca230718 kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware + IMAGE_SIZE := 51200k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += dlink_aquila-pro-ai-m60-a1 + define Device/edgecore_eap111 DEVICE_VENDOR := Edgecore DEVICE_MODEL := EAP111