mirror of
https://github.com/openwrt/openwrt.git
synced 2025-01-31 00:24:12 +00:00
ipq806x: add support for Fortinet FAP-421E
Hardware
--------
SoC: Qualcomm IPQ8064
RAM: 235MB
Flash: 128MB NAND (Micron MT29F1G08ABBDAH4)
32MB SPI-NOR (Spansion FL256SAIFRO)
WLAN2: Qualcomm Atheros QCA9980
WLAN5: Qualcomm Atheros QCA9980
ETH: LAN1 - Atheros AR8035
LAN2 - Atheros AR8033
USB: USB-A, 2.0
LED: Power (yellow/amber)
LAN1 (yellow/amber)
LAN2 (yellow/amber)
WLAN2G (yellow)
WLAN5G (yellow)
BTN: Reset
Serial: RJ45 Port (9600 8n1) Cisco console cable, TTL voltage
MAC Address: LAN1 (label) at APPSBL partition
LAN2: label + 1
WLAN2: label + 8
WLAN5: label + 16
Installation
------------
Connect to the RJ45 console (TTL)
Connect LAN1 to host, set host ip as 192.168.1.10
Start a tftp server to serve the initramfs image
Open console connection (9600n8)
Connect power through the DC jack
`Hit any key to stop autoboot: 5`: press any key
`Enter G,Q,or H:`: press `K` to access the hidden option
`Enter password:`: `fap22b1!$` to access a limited u-boot console
`(FAP) #`: `tftpboot your_initramfs_image_name.itb`
`(FAP) #`: `bootm`
Once OpenWrt has booted, install the firmware through sysupgrade
Signed-off-by: JinGen Lim <openwrt@sn.sg>
This commit is contained in:
JinGen Lim
Christian Marangi
parent
7173a52f6a
commit
b38d446ecd
@ -37,6 +37,15 @@ extreme,ap3935)
|
||||
ucidef_set_led_netdev "wan" "wan" "orange:lan1" "eth1"
|
||||
ucidef_set_led_netdev "lan" "lan" "orange:lan2" "eth0"
|
||||
;;
|
||||
fortinet,fap-421e)
|
||||
ucidef_set_led_netdev "eth1-100" "ETH1-100" "amber:eth1" "eth0" "link_100"
|
||||
ucidef_set_led_netdev "eth1-1000" "ETH1-1000" "yellow:eth1" "eth0" "link_1000"
|
||||
ucidef_set_led_netdev "eth2-100" "ETH2-100" "amber:eth2" "eth1" "link_100"
|
||||
ucidef_set_led_netdev "eth2-1000" "ETH2-1000" "yellow:eth2" "eth1" "link_1000"
|
||||
ucidef_set_led_wlan "wlan2g" "2.4G" "yellow:2g" "phy1tpt"
|
||||
ucidef_set_led_wlan "wlan5g" "5G" "yellow:5g" "phy0tpt"
|
||||
ucidef_set_led_usbport "usb" "USB" "amber:power" "usb1-port1" "usb2-port1"
|
||||
;;
|
||||
meraki,mr52)
|
||||
ucidef_set_led_netdev "eth0" "eth0" "green:lan1" "eth0"
|
||||
ucidef_set_led_netdev "eth1" "eth1" "green:lan2" "eth1"
|
||||
|
||||
@ -56,6 +56,7 @@ ipq806x_setup_interfaces()
|
||||
qcom,ipq8064-db149)
|
||||
ucidef_set_interface_lan "eth1 eth2 eth3 lan1 lan2 lan3 lan4" "wan"
|
||||
;;
|
||||
fortinet,fap-421e |\
|
||||
ubnt,unifi-ac-hd)
|
||||
ucidef_set_interface_lan "eth0 eth1"
|
||||
;;
|
||||
|
||||
@ -14,6 +14,7 @@ case "$(board_name)" in
|
||||
asrock,g10 |\
|
||||
buffalo,wxr-2533dhp |\
|
||||
compex,wpq864 |\
|
||||
fortinet,fap-421e |\
|
||||
nec,wg2600hp |\
|
||||
nec,wg2600hp3 |\
|
||||
netgear,d7800 |\
|
||||
|
||||
@ -13,6 +13,7 @@ platform_do_upgrade() {
|
||||
arris,tr4400-v2 |\
|
||||
askey,rt4230w-rev6 |\
|
||||
compex,wpq864|\
|
||||
fortinet,fap-421e|\
|
||||
netgear,d7800 |\
|
||||
netgear,r7500 |\
|
||||
netgear,r7500v2 |\
|
||||
|
||||
@ -0,0 +1,410 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq8064-smb208.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Fortinet FAP-421E";
|
||||
compatible = "fortinet,fap-421e", "qcom,ipq8064";
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x42000000 0xe000000>;
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
rsvd@41200000 {
|
||||
no-map;
|
||||
reg = <0x41200000 0x300000>;
|
||||
};
|
||||
wifi_dump@44000000 {
|
||||
no-map;
|
||||
reg = <0x44000000 0x600000>;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_yellow;
|
||||
led-failsafe = &led_power_yellow;
|
||||
led-running = &led_power_yellow;
|
||||
led-upgrade = &led_power_yellow;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-override = "console=ttyMSM0,9600n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
eth1_amber {
|
||||
label = "amber:eth1";
|
||||
gpios = <&qcom_pinmux 27 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth1_yellow {
|
||||
label = "yellow:eth1";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth2_amber {
|
||||
label = "amber:eth2";
|
||||
gpios = <&qcom_pinmux 29 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
eth2_yellow {
|
||||
label = "yellow:eth2";
|
||||
gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power_amber {
|
||||
label = "amber:power";
|
||||
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_yellow: power_yellow {
|
||||
label = "yellow:power";
|
||||
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
2g_yellow {
|
||||
label = "yellow:2g";
|
||||
gpios = <&qcom_pinmux 30 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
5g_yellow {
|
||||
label = "yellow:5g";
|
||||
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qcom_pinmux {
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
bias-pull-up;
|
||||
drive-strength = <2>;
|
||||
pins = "gpio56";
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
bias-pull-down;
|
||||
drive-strength = <2>;
|
||||
function = "gpio";
|
||||
output-low;
|
||||
pins = "gpio23";
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2-pins {
|
||||
mux {
|
||||
bias-disable;
|
||||
drive-strength = <16>;
|
||||
function = "rgmii2";
|
||||
pins = "gpio66";
|
||||
};
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
data {
|
||||
pins = "gpio18", "gpio19";
|
||||
drive-strength = <10>;
|
||||
};
|
||||
|
||||
cs {
|
||||
pins = "gpio20";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
|
||||
uart0_pins: uart0_pins {
|
||||
mux {
|
||||
bias-disable;
|
||||
drive-strength = <12>;
|
||||
function = "gsbi7";
|
||||
pins = "gpio6", "gpio7";
|
||||
};
|
||||
};
|
||||
|
||||
usb_pwr_en_pins: usb_pwr_en_pins {
|
||||
mux {
|
||||
pins = "gpio22";
|
||||
function = "gpio";
|
||||
drive-strength = <12>;
|
||||
bias-pull-down;
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi7 {
|
||||
status = "okay";
|
||||
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
};
|
||||
|
||||
&gsbi7_serial{
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&uart0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&gsbi5 {
|
||||
status = "okay";
|
||||
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
|
||||
spi@1a280000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
m25p,fast-read;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x20000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "SBL2";
|
||||
reg = <0x40000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "SBL3";
|
||||
reg = <0x80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "DDRCONFIG";
|
||||
reg = <0x100000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@110000 {
|
||||
label = "SSD";
|
||||
reg = <0x110000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@120000 {
|
||||
label = "TZ";
|
||||
reg = <0x120000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1a0000 {
|
||||
label = "RPM";
|
||||
reg = <0x1a0000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x220000 0x80000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_appsbl_7ff80: mac-address@7ff80 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x7ff80 0xc>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@2a0000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x2a0000 0x40000>;
|
||||
};
|
||||
|
||||
partition@2e0000 {
|
||||
label = "ART";
|
||||
reg = <0x2e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@320000 {
|
||||
label = "kernel";
|
||||
reg = <0x320000 0x600000>;
|
||||
};
|
||||
|
||||
partition@920000 {
|
||||
label = "ubi";
|
||||
reg = <0x920000 0x1400000>;
|
||||
};
|
||||
|
||||
partition@1d20000 {
|
||||
label = "reserved";
|
||||
reg = <0x1d20000 0x260000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1f80000 {
|
||||
label = "config";
|
||||
reg = <0x1f80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hs_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&usb_pwr_en_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
compatible = "pci168c,0040";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
|
||||
nvmem-cells = <&macaddr_appsbl_7ff80 8>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
|
||||
max-link-speed = <1>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@1,0 {
|
||||
compatible = "pci168c,0040";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
|
||||
nvmem-cells = <&macaddr_appsbl_7ff80 16>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
#address-cells = <0x1>;
|
||||
#size-cells = <0x0>;
|
||||
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
|
||||
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
phy2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <0>;
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
nvmem-cells = <&macaddr_appsbl_7ff80 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
nvmem-cells = <&macaddr_appsbl_7ff80 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
@ -177,6 +177,18 @@ define Device/extreme_ap3935
|
||||
endef
|
||||
TARGET_DEVICES += extreme_ap3935
|
||||
|
||||
define Device/fortinet_fap-421e
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := Fortinet
|
||||
DEVICE_MODEL := FAP-421E
|
||||
SOC := qcom-ipq8064
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
BOARD_NAME := fap-421e
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += fortinet_fap-421e
|
||||
|
||||
define Device/linksys_ea7500-v1
|
||||
$(call Device/LegacyImage)
|
||||
$(Device/kernel-size-migration)
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user