Revert "ipq807x: add initial support for prpl Foundation Haze board"

This reverts commit 48603a271e as this
was commited by accident, its still work in progress.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

package/boot/uboot-envtools/files/ipq807x

@@ -36,11 +36,6 @@ xiaomi,ax9000)
 	[ -n "$idx2" ] && \
 		ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x10000" "0x20000"
 	;;
-prpl,haze)
-	mmcpart="$(find_mmc_part 0:APPSBLENV)"
-	[ -n "$mmcpart" ] && \
-		ubootenv_add_uci_config "$mmcpart" "0x0" "0x40000" "0x400" "0x100"
-	;;
 qnap,301w)
 	idx="$(find_mtd_index 0:appsblenv)"
 	[ -n "$idx" ] && \

target/linux/ipq807x/base-files/etc/board.d/02_network

@@ -25,9 +25,6 @@ ipq807x_setup_interfaces()
 	netgear,wax218)
 		ucidef_set_interface_lan "lan" "dhcp"
 		;;
-	prpl,haze)
-		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
-		;;
 	qnap,301w)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1"
 		;;

target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata

@@ -22,17 +22,10 @@ case "$FIRMWARE" in
 	zyxel,nbg7815)
 		caldata_extract "0:art" 0x1000 0x20000
 		;;
-	prpl,haze)
-                caldata_extract_mmc "0:ART" 0x1000 0x20000
-		;;
 	esac
 	;;
-"ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin"|\
+"ath11k/QCN9074/hw1.0/cal-pci-0000:01:00.0.bin")
-"ath11k/QCN9074/hw1.0/cal-pci-0001:01:00.0.bin")
 	case "$board" in
-	prpl,haze)
-                caldata_extract_mmc "0:ART" 0x26800 0x20000
-		;;
 	xiaomi,ax9000)
 		caldata_extract "0:art" 0x26800 0x20000
 		;;

target/linux/ipq807x/base-files/lib/upgrade/platform.sh

@@ -71,7 +71,6 @@ platform_do_upgrade() {
 	netgear,wax218)
 		nand_do_upgrade "$1"
 		;;
-	prpl,haze|\
 	qnap,301w)
 		kernelname="0:HLOS"
 		rootfsname="rootfs"

target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-haze.dts

@@ -1,311 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-/dts-v1/;
-
-#include "ipq8074.dtsi"
-#include "ipq8074-hk-cpu.dtsi"
-#include "ipq8074-ess.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
-	model = "prpl Foundation Haze";
-	compatible = "prpl,haze", "qcom,ipq8074";
-
-	aliases {
-		serial0 = &blsp1_uart5;
-		/* Aliases are required by U-Boot to patch MAC addresses */
-		ethernet0 = &dp6_syn;
-		ethernet1 = &dp4;
-		ethernet2 = &dp3;
-		ethernet3 = &dp2;
-		label-mac-device = &dp6_syn;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	keys {
-		compatible = "gpio-keys";
-		pinctrl-0 = <&button_pins>;
-		pinctrl-names = "default";
-
-		wps-button {
-			label = "wps";
-			gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WPS_BUTTON>;
-		};
-
-		reset-button {
-			label = "reset";
-			gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_RESTART>;
-		};
-	};
-};
-
-&tlmm {
-	mdio_pins: mdio-state {
-		mdc-pins {
-			pins = "gpio68";
-			function = "mdc";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-
-		mdio-pins {
-			pins = "gpio69";
-			function = "mdio";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-	};
-
-	button_pins: button-state {
-		wps-pins {
-			pins = "gpio42";
-			function = "gpio";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-
-		rst-pins {
-			pins = "gpio44";
-			function = "gpio";
-			drive-strength = <8>;
-			bias-pull-up;
-		};
-	};
-};
-
-&blsp1_uart5 {
-	status = "okay";
-};
-
-&prng {
-	status = "okay";
-};
-
-&ssphy_0 {
-	status = "okay";
-};
-
-&qusb_phy_0 {
-	status = "okay";
-};
-
-&ssphy_1 {
-	status = "okay";
-};
-
-&qusb_phy_1 {
-	status = "okay";
-};
-
-&usb_0 {
-	status = "okay";
-};
-
-&usb_1 {
-	status = "okay";
-};
-
-&cryptobam {
-	status = "okay";
-};
-
-&crypto {
-	status = "okay";
-};
-
-&qpic_bam {
-	status = "okay";
-};
-
-&blsp1_spi1 { /* BLSP1 QUP1 */
-	pinctrl-0 = <&spi_0_pins>;
-	pinctrl-names = "default";
-	cs-gpios = <0>;
-	status = "okay";
-
-	flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		reg = <0>;
-		compatible = "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
-
-		partitions {
-			compatible = "qcom,smem-part";
-		};
-	};
-};
-
-&mdio {
-	status = "okay";
-
-	pinctrl-0 = <&mdio_pins>;
-	pinctrl-names = "default";
-	reset-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
-
-	qca8075_1: ethernet-phy@0 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0>;
-	};
-
-	qca8075_2: ethernet-phy@1 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <1>;
-	};
-
-	qca8075_3: ethernet-phy@2 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <2>;
-	};
-
-	qca8075_4: ethernet-phy@3 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <3>;
-	};
-
-	aqr113c: ethernet-phy@5 {
-		compatible ="ethernet-phy-ieee802.3-c45";
-		reg = <8>;
-		reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&sdhc_1 {
-	status = "okay";
-
-	mmc-hs400-1_8v;
-	mmc-hs200-1_8v;
-	mmc-ddr-1_8v;
-	vqmmc-supply = <&l11>;
-};
-
-&switch {
-	status = "okay";
-
-	switch_cpu_bmp = <0x1>;  /* cpu port bitmap */
-	switch_lan_bmp = <0x1e>; /* lan port bitmap */
-	switch_wan_bmp = <0x60>; /* wan port bitmap */
-	switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
-	switch_mac_mode1 = <0xe>; /* mac mode for uniphy instance1*/
-	switch_mac_mode2 = <0xd>; /* mac mode for uniphy instance2*/
-	bm_tick_mode = <0>; /* bm tick mode */
-	tm_tick_mode = <0>; /* tm tick mode */
-
-	qcom,port_phyinfo {
-		port@0 {
-			port_id = <1>;
-			phy_address = <0>;
-		};
-		port@1 {
-			port_id = <2>;
-			phy_address = <1>;
-		};
-		port@2 {
-			port_id = <3>;
-			phy_address = <2>;
-		};
-		port@3 {
-			port_id = <4>;
-			phy_address = <3>;
-		};
-		port@4 {
-			port_id = <6>;
-			phy_address = <8>;
-			compatible = "ethernet-phy-ieee802.3-c45";
-			ethernet-phy-ieee802.3-c45;
-		};
-	};
-};
-
-&edma {
-	status = "okay";
-};
-
-/* Dummy LAN port */
-&dp1 {
-	status = "disabled";
-	phy-handle = <&qca8075_1>;
-	label = "lan4";
-};
-
-&dp2 {
-	status = "okay";
-	phy-handle = <&qca8075_2>;
-	label = "lan3";
-};
-
-&dp3 {
-	status = "okay";
-	phy-handle = <&qca8075_3>;
-	label = "lan2";
-};
-
-&dp4 {
-	status = "okay";
-	phy-handle = <&qca8075_4>;
-	label = "lan1";
-};
-
-&dp6_syn {
-	status = "okay";
-	qcom,mactype = <1>;
-	phy-handle = <&aqr113c>;
-	label = "wan";
-};
-
-&pcie_qmp0 {
-	status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-
-	perst-gpio = <&tlmm 58 GPIO_ACTIVE_LOW>;
-
-	bridge@0,0 {
-		reg = <0x00020000 0 0 0 0>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		ranges;
-	};
-};
-
-&pcie_qmp1 {
-	status = "okay";
-};
-
-&pcie1 {
-	status = "okay";
-
-	perst-gpio = <&tlmm 61 GPIO_ACTIVE_LOW>;
-
-	bridge@1,0 {
-		reg = <0x00010000 0 0 0 0>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		ranges;
-
-		wifi@1,0 {
-			status = "okay";
-
-			/* ath11k has no DT compatible for PCI cards */
-			compatible = "pci17cb,1104";
-			reg = <0x00010000 0 0 0 0>;
-
-			qcom,ath11k-calibration-variant = "prpl-Haze";
-		};
-	};
-};
-
-&wifi {
-	status = "okay";
-
-	qcom,ath11k-calibration-variant = "prpl-Haze";
-};

target/linux/ipq807x/image/generic.mk

@@ -108,18 +108,6 @@ define Device/netgear_wax218
 endef
 TARGET_DEVICES += netgear_wax218
 
-define Device/prpl_haze
-	$(call Device/FitImage)
-	$(call Device/EmmcImage)
-	DEVICE_VENDOR := prpl Foundation
-	DEVICE_MODEL := Haze
-	DEVICE_DTS_CONFIG := config@hk09
-	SOC := ipq8072
-	DEVICE_PACKAGES += ath11k-firmware-qcn9074 ipq-wifi-prpl_haze kmod-ath11k-pci
-	DEFAULT_PACKAGES += ath11k-firmware-qcn9074 ipq-wifi-prpl_haze kmod-ath11k-pci
-endef
-TARGET_DEVICES += prpl_haze
-
 define Device/qnap_301w
 	$(call Device/FitImage)
 	$(call Device/EmmcImage)