mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-03 17:50:49 +00:00
kirkwood: add support for Ctera C200 V1 NAS
2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 256MB (Samsung 216 K9F2G08U0C) - Lan: 1x GBE (Marvell 88E1116R-NNC1) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 2.0 port - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ctera_c200-v1_back_to_factory Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> [apply sorting to device recipe] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit is contained in:
Pawel Dembicki
Sungbo Eo
parent
e22c91e144
commit
3843c641d8
@ -18,6 +18,7 @@ cisco,on100)
|
||||
;;
|
||||
cloudengines,pogoe02|\
|
||||
cloudengines,pogoplugv4|\
|
||||
ctera,c200-v1|\
|
||||
globalscale,sheevaplug|\
|
||||
iom,iconnect-1.1|\
|
||||
iom,ix2-200|\
|
||||
|
||||
@ -7,6 +7,13 @@ boot() {
|
||||
# for more information, please read https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface
|
||||
|
||||
case $(board_name) in
|
||||
ctera,c200-v1)
|
||||
path_to_hwmon='/sys/devices/platform/ocp@f1000000/f1011000.i2c/i2c-0/0-004c/hwmon/hwmon0'
|
||||
|
||||
# It should be related to hdd temerature instead lm63 temp
|
||||
echo 1 > "$path_to_hwmon/pwm1_enable"
|
||||
echo 128 > "$path_to_hwmon/pwm1"
|
||||
;;
|
||||
iom,ix2-200)
|
||||
path_to_hwmon='/sys/class/hwmon/hwmon0'
|
||||
echo 2 > "$path_to_hwmon/pwm1_enable" # fan is on pwm1
|
||||
|
||||
@ -1,4 +1,4 @@
|
||||
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
||||
RAMFS_COPY_BIN='fw_printenv fw_setenv strings'
|
||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||
|
||||
REQUIRE_IMAGE_METADATA=1
|
||||
@ -11,6 +11,17 @@ platform_do_upgrade() {
|
||||
local board="$(board_name)"
|
||||
|
||||
case "$board" in
|
||||
ctera,c200-v1)
|
||||
part=$(find_mtd_part "active_bank")
|
||||
|
||||
if [ -n "$part" ]; then
|
||||
CI_KERNPART="$(strings $part | grep bank)"
|
||||
nand_do_upgrade "$1"
|
||||
else
|
||||
echo "active_bank partition missed!"
|
||||
return 1
|
||||
fi
|
||||
;;
|
||||
linksys,e4200-v2|\
|
||||
linksys,ea3500|\
|
||||
linksys,ea4500)
|
||||
|
||||
28
target/linux/kirkwood/base-files/sbin/ctera_c200-v1_back_to_factory
Executable file
28
target/linux/kirkwood/base-files/sbin/ctera_c200-v1_back_to_factory
Executable file
@ -0,0 +1,28 @@
|
||||
#!/bin/sh
|
||||
|
||||
. /lib/functions.sh
|
||||
|
||||
case $(board_name) in
|
||||
ctera,c200-v1)
|
||||
part=$(find_mtd_part "active_bank")
|
||||
|
||||
if [ -n "$part" ]; then
|
||||
active_bank="$(strings $part | grep bank)"
|
||||
|
||||
if [ $active_bank = "bank1" ]; then
|
||||
echo "bank2" > /tmp/change_bank
|
||||
else
|
||||
echo "bank1" > /tmp/change_bank
|
||||
fi
|
||||
|
||||
mtd write /tmp/change_bank active_bank
|
||||
reboot
|
||||
else
|
||||
echo "active_bank partition missed!"
|
||||
return 1
|
||||
fi
|
||||
;;
|
||||
*)
|
||||
echo "Unsupported hardware."
|
||||
;;
|
||||
esac
|
||||
@ -0,0 +1,303 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later
|
||||
/*
|
||||
* Ctera C200 V1 Board Description
|
||||
* Copyright 2021 Pawel Dembicki <paweldembicki@gmail.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "kirkwood.dtsi"
|
||||
#include "kirkwood-6281.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Ctera C200 V1";
|
||||
compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_red;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
stdout-path = &uart0;
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x20000000>;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&pmx_buttons>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
power {
|
||||
label = "Power Button";
|
||||
linux,code = <KEY_POWER>;
|
||||
gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "Reset Button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb1 {
|
||||
label = "USB1 Button";
|
||||
linux,code = <BTN_0>;
|
||||
gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb2 {
|
||||
label = "USB2 Button";
|
||||
linux,code = <BTN_1>;
|
||||
gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-poweroff {
|
||||
compatible = "gpio-poweroff";
|
||||
pinctrl-0 = <&pmx_poweroff>;
|
||||
pinctrl-names = "default";
|
||||
gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&pmx_leds>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led_status_green: status-green {
|
||||
label = "green:status";
|
||||
gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status_red: status-red {
|
||||
label = "red:status";
|
||||
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
cloud-blue {
|
||||
label = "blue:cloud";
|
||||
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
disk1-green {
|
||||
label = "green:disk1";
|
||||
gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "ata1";
|
||||
};
|
||||
|
||||
disk1-red {
|
||||
label = "red:disk1";
|
||||
gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
disk2-green {
|
||||
label = "green:disk2";
|
||||
gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "ata2";
|
||||
};
|
||||
|
||||
disk2-red {
|
||||
label = "red:disk2";
|
||||
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
disk-fail-green {
|
||||
label = "green:disk-fail";
|
||||
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
disk-fail-red {
|
||||
label = "red:disk-fail";
|
||||
gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb1-green {
|
||||
label = "green:usb1";
|
||||
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&hub_port2>;
|
||||
};
|
||||
|
||||
usb1-red {
|
||||
label = "red:usb1";
|
||||
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb2-green {
|
||||
label = "green:usb2";
|
||||
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&hub_port1>;
|
||||
};
|
||||
|
||||
usb2-red {
|
||||
label = "red:usb2";
|
||||
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð0port {
|
||||
phy-handle = <ðphy9>;
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
|
||||
rtc@30 {
|
||||
compatible = "s35390a";
|
||||
reg = <0x30>;
|
||||
};
|
||||
|
||||
lm63@4c {
|
||||
compatible = "national,lm63";
|
||||
reg = <0x4c>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
ethphy9: ethernet-phy@9 {
|
||||
reg = <9>;
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
status = "okay";
|
||||
chip-delay = <40>;
|
||||
|
||||
partition@0 {
|
||||
label = "uboot";
|
||||
reg = <0x0000000 0x200000>;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "certificate";
|
||||
reg = <0x0200000 0x100000>;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "preset_cfg";
|
||||
reg = <0x0300000 0x100000>;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "dev_params";
|
||||
reg = <0x0400000 0x100000>;
|
||||
};
|
||||
partition@500000 {
|
||||
label = "active_bank";
|
||||
reg = <0x0500000 0x0100000>;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "magic";
|
||||
reg = <0x0600000 0x0100000>;
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "bank1";
|
||||
reg = <0x0700000 0x2800000>;
|
||||
};
|
||||
|
||||
partition@2f00000 {
|
||||
label = "bank2";
|
||||
reg = <0x2f00000 0x2800000>;
|
||||
};
|
||||
|
||||
/* 0x5700000-0x5a00000 undefined in vendor firmware */
|
||||
|
||||
partition@5a00000 {
|
||||
label = "reserved";
|
||||
reg = <0x5a00000 0x2000000>;
|
||||
};
|
||||
|
||||
partition@7a00000 {
|
||||
label = "ubi";
|
||||
reg = <0x7a00000 0x8600000>;
|
||||
};
|
||||
};
|
||||
|
||||
&pciec {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
/* buzzer gpios are connected to two pins of buzzer
|
||||
* leave it as is due lack of proper driver
|
||||
*/
|
||||
pmx_buzzer: pmx-buzzer {
|
||||
marvell,pins = "mpp12", "mpp13";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_leds: pmx-leds {
|
||||
marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
|
||||
"mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
|
||||
"mpp45", "mpp46", "mpp47";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_buttons: pmx-buttons {
|
||||
marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
pmx_poweroff: pmx-poweroff {
|
||||
marvell,pins = "mpp34";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
&rtc {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&sata {
|
||||
status = "okay";
|
||||
nr-ports = <2>;
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
port@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
|
||||
hub_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
|
||||
hub_port2: port@2 {
|
||||
reg = <2>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -7,6 +7,63 @@ include $(INCLUDE_DIR)/image.mk
|
||||
|
||||
KERNEL_LOADADDR:=0x8000
|
||||
|
||||
# Some info about Ctera firmware:
|
||||
# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
|
||||
# 2. It contains two images: kernel and romdisk. Both are required.
|
||||
# 3. Every image has header and trailer file.
|
||||
# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
|
||||
# 5. In header file are some strings used to describe image. It was decoded from
|
||||
# factory image.
|
||||
# 6. Version format in header file is restricted by Original FW.
|
||||
# 7. Trailer file contains MD5 sum string of header and image file.
|
||||
# 8. Firmware file must have <=24MB size.
|
||||
|
||||
define Build/ctera-firmware
|
||||
mkdir -p $@.tmp
|
||||
|
||||
# Prepare header and trailer file for kernel
|
||||
echo "# CTera firmware information file" > $@.tmp/header
|
||||
echo "image_type=kernel" >> $@.tmp/header
|
||||
echo "arch=Kirkwood" >> $@.tmp/header
|
||||
echo "board=Any" >> $@.tmp/header
|
||||
echo "version=3.1.22.30669" >> $@.tmp/header
|
||||
echo "kernel_cmd=console=ttyS0,115200 earlyprintk" >> $@.tmp/header
|
||||
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
||||
>> $@.tmp/header
|
||||
|
||||
cp $@ $@.tmp/kernel
|
||||
|
||||
echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
|
||||
> $@.tmp/trailer
|
||||
|
||||
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
||||
-H gnu -C $@.tmp -cf $@.tar header kernel trailer
|
||||
|
||||
# Prepare header and trailer file for fake romdisk
|
||||
echo "# CTera firmware information file" > $@.tmp/header
|
||||
echo "image_type=romdisk" >> $@.tmp/header
|
||||
echo "initrd=yes" >> $@.tmp/header
|
||||
echo "arch=Kirkwood" >> $@.tmp/header
|
||||
echo "board=Any" >> $@.tmp/header
|
||||
echo "version=3.1.22.30669" >> $@.tmp/header
|
||||
echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
|
||||
>> $@.tmp/header
|
||||
|
||||
rm -f $@
|
||||
touch $@
|
||||
$(call Build/append-uImage-fakehdr, ramdisk)
|
||||
cp $@ $@.tmp/romdisk
|
||||
|
||||
echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
|
||||
> $@.tmp/trailer
|
||||
|
||||
tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
|
||||
-H gnu -C $@.tmp -rf $@.tar header romdisk trailer
|
||||
|
||||
mv $@.tar $@
|
||||
rm -rf $@.tmp
|
||||
endef
|
||||
|
||||
define Device/kernel-size-migration
|
||||
DEVICE_COMPAT_VERSION := 2.0
|
||||
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to \
|
||||
@ -70,6 +127,19 @@ define Device/cloudengines_pogoplugv4
|
||||
endef
|
||||
TARGET_DEVICES += cloudengines_pogoplugv4
|
||||
|
||||
define Device/ctera_c200-v1
|
||||
DEVICE_VENDOR := Ctera
|
||||
DEVICE_MODEL := C200
|
||||
DEVICE_VARIANT := V1
|
||||
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-gpio-button-hotplug \
|
||||
kmod-hwmon-lm63 kmod-rtc-s35390a kmod-usb-ledtrig-usbport
|
||||
KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
|
||||
KERNEL_IN_UBI :=
|
||||
KERNEL_SUFFIX := -factory.firm
|
||||
IMAGES := sysupgrade.bin
|
||||
endef
|
||||
TARGET_DEVICES += ctera_c200-v1
|
||||
|
||||
define Device/globalscale_sheevaplug
|
||||
DEVICE_VENDOR := Globalscale
|
||||
DEVICE_MODEL := Sheevaplug
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user