ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50

The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.

This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.

Hardware
--------
SoC:   Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM:   512MB DDR3
FLASH: 4GB EMMC
ETH:
  - 3x 10/100/1000 Mbps Ethernet
  - 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
  - 2.4GHz: 1x IPQ4019 (2x2:2)
  - 5GHz:   1x IPQ4019 (2x2:2)
  - 5GHz:   1x QCA9984 (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x Sync button
  - 1x ON/OFF button
LEDS:
  - 8 leds controlled by TLC59208F (they can be switched on/off
    independendently but the color can by changed by GPIOs)
  - 1x Red led (Power)
  - 1x Green led (Power)
UART:
  - 115200-8-N-1

Everything works correctly.

Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.

The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.

There are 2 ways to install Openwrt the first time:

1) Using NMRPflash
 1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
	file in the same folder of the nmrpflash executable
 3. Connect your pc to the router using the port near the power button.
 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
	Replace XXX with your network interface (can be identified by
	running "nmrpflash -L")
 5. Power on the router and wait for the flash to complete. After about
	a minute the router should boot directly to Openwrt. If nothing
	happens try to reboot the router. If you have problems flashing
	try to set "10.164.183.253" as your computer IP address

2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.

To switch on partition 2 you have to enable telnet first:
 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
 2. Connect through telent ("telnet 192.168.1.250") and login using
	admin/password.

	To read the current boot_part:
		artmtd -r boot_part

	To write the new boot_part:
		artmtd -w boot_part 02

	Then reboot the router and then check again the current booted
	partition

Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.

Restore OEM Firmware
--------------------
 1. Download the stock firmware from official netgear support.
 2. Follow the nmrpflash procedure like above, using the official
	Netgear firmware (for example SRS60-V2.2.1.210.img)

        nmrpflash -i XXX -f SRS60-V2.2.1.210.img

Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
	the UART connection.
	"boot_partition_show" shows the current boot partition
	"boot_partition_set 1" sets the current boot partition to 1

2) Router mac addresses:

   LAN XX:XX:XX:XX:XX:69
   WAN XX:XX:XX:XX:XX:6a
   WIFI 2G XX:XX:XX:XX:XX:69
   WIFI 5G XX:XX:XX:XX:XX:6b
   WIFI 5G (2nd) XX:XX:XX:XX:XX:6c

   LABEL XX:XX:XX:XX:XX:69

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit is contained in:
Davide Fioravanti 2020-09-02 02:10:16 +02:00 committed by Christian Lamparter
parent 6e13794344
commit 2cb24b3f3c
12 changed files with 591 additions and 5 deletions

View File

@ -106,6 +106,14 @@ ipq40xx_setup_interfaces()
"0u@eth0" "3:lan:2" "4:lan:1" "0u@eth0" "3:lan:2" "4:lan:1"
ucidef_set_interface_wan "eth1" ucidef_set_interface_wan "eth1"
;; ;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan" "3:lan" "4:lan"
ucidef_set_interface_wan "eth1"
;;
qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2) qxwlan,e2600ac-c2)
ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_set_interfaces_lan_wan "eth0" "eth1"

View File

@ -46,6 +46,13 @@ case "$FIRMWARE" in
# OEM assigns 4 sequential MACs # OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4)) ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
;; ;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
caldata_extract_mmc "0:ART" 0x9000 0x2f20
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x12)
;;
esac esac
;; ;;
"ath10k/pre-cal-ahb-a000000.wifi.bin") "ath10k/pre-cal-ahb-a000000.wifi.bin")
@ -150,6 +157,13 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x1000 0x2f20 caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary dnidata 0x0) ath10k_patch_mac $(mtd_get_mac_binary dnidata 0x0)
;; ;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
caldata_extract_mmc "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x0)
;;
netgear,wac510) netgear,wac510)
caldata_extract "0:ART" 0x1000 0x2f20 caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary "0:MANUDATA" 0x6) ath10k_patch_mac $(mtd_get_mac_binary "0:MANUDATA" 0x6)
@ -264,6 +278,13 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x5000 0x2f20 caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary dnidata 0xc) ath10k_patch_mac $(mtd_get_mac_binary dnidata 0xc)
;; ;;
netgear,rbr50|\
netgear,rbs50|\
netgear,srr60|\
netgear,srs60)
caldata_extract_mmc "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0xc)
;;
netgear,wac510) netgear,wac510)
caldata_extract "0:ART" 0x5000 0x2f20 caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:MANUDATA" 0x6) 16) ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:MANUDATA" 0x6) 16)

View File

@ -0,0 +1,76 @@
# SPDX-License-Identifier: GPL-2.0-only
. /lib/functions.sh
platform_do_upgrade_netgear_orbi_upgrade() {
command -v losetup >/dev/null || {
logger -s "Upgrade failed: 'losetup' not installed."
return 1
}
local tar_file=$1
local kernel=$2
local rootfs=$3
[ -z "$kernel" ] && kernel=$(find_mmc_part "kernel")
[ -z "$rootfs" ] && rootfs=$(find_mmc_part "rootfs")
[ -z "$kernel" ] && echo "Upgrade failed: kernel partition not found! Rebooting..." && reboot -f
[ -z "$rootfs" ] && echo "Upgrade failed: rootfs partition not found! Rebooting..." && reboot -f
netgear_orbi_do_flash $tar_file $kernel $rootfs
echo "sysupgrade successful"
umount -a
reboot -f
}
netgear_orbi_do_flash() {
local tar_file=$1
local kernel=$2
local rootfs=$3
# keep sure its unbound
losetup --detach-all || {
echo "Failed to detach all loop devices. Skip this try."
reboot -f
}
# use the first found directory in the tar archive
local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
board_dir=${board_dir%/}
echo "flashing kernel to $kernel"
tar xf $tar_file ${board_dir}/kernel -O >$kernel
echo "flashing rootfs to ${rootfs}"
tar xf $tar_file ${board_dir}/root -O >"${rootfs}"
# a padded rootfs is needed for overlay fs creation
local offset=$(tar xf $tar_file ${board_dir}/root -O | wc -c)
[ $offset -lt 65536 ] && {
echo "Wrong size for rootfs: $offset"
sleep 10
reboot -f
}
# Mount loop for rootfs_data
local loopdev="$(losetup -f)"
losetup -o $offset $loopdev $rootfs || {
echo "Failed to mount looped rootfs_data."
sleep 10
reboot -f
}
echo "Format new rootfs_data at position ${offset}."
mkfs.ext4 -F -L rootfs_data $loopdev
mkdir /tmp/new_root
mount -t ext4 $loopdev /tmp/new_root && {
echo "Saving config to rootfs_data at position ${offset}."
cp -v "$UPGRADE_BACKUP" "/tmp/new_root/$BACKUP_FILE"
umount /tmp/new_root
}
# Cleanup
losetup -d $loopdev >/dev/null 2>&1
sync
}

View File

@ -117,6 +117,12 @@ platform_do_upgrade() {
[ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware [ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware
default_do_upgrade "$1" default_do_upgrade "$1"
;; ;;
netgear,rbr50 |\
netgear,rbs50 |\
netgear,srr60 |\
netgear,srs60)
platform_do_upgrade_netgear_orbi_upgrade "$1"
;;
openmesh,a42 |\ openmesh,a42 |\
openmesh,a62 |\ openmesh,a62 |\
plasmacloud,pa1200 |\ plasmacloud,pa1200 |\

View File

@ -0,0 +1,325 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/soc/qcom,tcsr.h>
/ {
aliases {
led-boot = &led_status_white;
led-failsafe = &led_status_red;
led-running = &led_status_green;
led-upgrade = &led_status_blue;
};
soc {
rng@22000 {
status = "okay";
};
mdio@90000 {
status = "okay";
pinctrl-0 = <&mdio_pins>;
pinctrl-names = "default";
};
ess-psgmii@98000 {
status = "okay";
};
counter@4a1000 {
compatible = "qcom,qca-gcnt";
reg = <0x4a1000 0x4>;
};
tcsr@1949000 {
compatible = "qcom,tcsr";
reg = <0x1949000 0x100>;
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
};
tcsr@194b000 {
status = "okay";
compatible = "qcom,tcsr";
reg = <0x194b000 0x100>;
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
};
ess_tcsr@1953000 {
compatible = "qcom,tcsr";
reg = <0x1953000 0x1000>;
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
};
tcsr@1957000 {
compatible = "qcom,tcsr";
reg = <0x1957000 0x100>;
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
};
crypto@8e3a000 {
status = "okay";
};
watchdog@b017000 {
status = "okay";
};
ess-switch@c000000 {
status = "okay";
switch_lan_bmp = <0x1c>;
switch_wan_bmp = <0x02>;
};
edma@c080000 {
status = "okay";
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&tlmm 49 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
led-0 {
label = "green:power";
gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
led-1 {
label = "red:power";
gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
panic-indicator;
};
led_status_green: led-2 {
label = "green:status";
gpios = <&tlmm 53 GPIO_ACTIVE_HIGH>;
};
led_status_red: led-3 {
label = "red:status";
gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
};
led_status_blue: led-4 {
label = "blue:status";
gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>;
};
led_status_white: led-5 {
label = "white:status";
gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
};
};
};
&vqmmc {
status = "okay";
};
&sdhci {
status = "okay";
pinctrl-0 = <&sd_pins>;
pinctrl-names = "default";
cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
vqmmc-supply = <&vqmmc>;
};
&qpic_bam {
status = "okay";
};
&tlmm {
mdio_pins: mdio_pinmux {
mux_1 {
pins = "gpio6";
function = "mdio";
bias-pull-up;
};
mux_2 {
pins = "gpio7";
function = "mdc";
bias-pull-up;
};
};
serial_pins: serial_pinmux {
mux {
pins = "gpio16", "gpio17";
function = "blsp_uart0";
bias-disable;
};
};
i2c_0_pins: i2c_0_pinmux {
pinmux {
function = "blsp_i2c0";
pins = "gpio58", "gpio59";
bias-disable;
};
};
sd_pins: sd_pins {
pinmux {
function = "sdio";
pins = "gpio23", "gpio24", "gpio25", "gpio26",
"gpio28", "gpio29", "gpio30", "gpio31";
drive-strength = <10>;
};
pinmux_sd_clk {
function = "sdio";
pins = "gpio27";
drive-strength = <16>;
};
pinmux_sd7 {
function = "sdio";
pins = "gpio32";
drive-strength = <10>;
bias-disable;
};
};
};
&blsp_dma {
status = "okay";
};
&blsp1_i2c3 {
pinctrl-0 = <&i2c_0_pins>;
pinctrl-names = "default";
status = "okay";
led-controller@27 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "ti,tlc59108"; /* really is tlc59208f */
reg = <0x27>;
led0@0 {
label = "rgb:led0";
reg = <0x0>;
linux,default-trigger = "default-on";
};
led1@1 {
label = "rgb:led1";
reg = <0x1>;
linux,default-trigger = "default-on";
};
led2@2 {
label = "rgb:led2";
reg = <0x2>;
linux,default-trigger = "default-on";
};
led3@3 {
label = "rgb:led3";
reg = <0x3>;
linux,default-trigger = "default-on";
};
led4@4 {
label = "rgb:led4";
reg = <0x4>;
linux,default-trigger = "default-on";
};
led5@5 {
label = "rgb:led5";
reg = <0x5>;
linux,default-trigger = "default-on";
};
led6@6 {
label = "rgb:led6";
reg = <0x6>;
linux,default-trigger = "default-on";
};
led7@7 {
label = "rgb:led7";
reg = <0x7>;
linux,default-trigger = "default-on";
};
};
};
&blsp1_uart1 {
status = "okay";
pinctrl-0 = <&serial_pins>;
pinctrl-names = "default";
};
&cryptobam {
status = "okay";
};
&gmac0 {
vlan_tag = <1 0x1c>;
};
&gmac1 {
qcom,phy_mdio_addr = <0>;
vlan_tag = <2 0x02>;
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
bridge@0,0 {
reg = <0x00000000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
wifi@1,0 {
compatible = "qcom,ath10k";
status = "okay";
reg = <0x00010000 0 0 0 0>;
ieee80211-freq-limit = <5470000 5875000>;
qcom,ath10k-calibration-variant = "Netgear-Orbi-Pro-SRK60";
};
};
};
&wifi0 {
status = "okay";
qcom,ath10k-calibration-variant = "Netgear-Orbi-Pro-SRK60";
};
&wifi1 {
status = "okay";
qcom,ath10k-calibration-variant = "Netgear-Orbi-Pro-SRK60";
};

View File

@ -0,0 +1,30 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019-orbi.dtsi"
/ {
model = "NETGEAR RBR50";
compatible = "netgear,rbr50";
chosen {
bootargs = "root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_ALT)ro,256K(0:CDT)ro,256K(0:CDT_ALT)ro,256K(0:DDRPARAMS)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_ALT)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,1457651200(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait";
};
soc {
usb2@60f8800 {
status = "okay";
};
usb3@8af8800 {
status = "okay";
};
};
};
&usb3_hs_phy {
status = "okay";
};
&usb2_hs_phy {
status = "okay";
};

View File

@ -0,0 +1,30 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019-orbi.dtsi"
/ {
model = "NETGEAR RBS50";
compatible = "netgear,rbs50";
chosen {
bootargs = "root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_ALT)ro,256K(0:CDT)ro,256K(0:CDT_ALT)ro,256K(0:DDRPARAMS)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_ALT)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,1457651200(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait";
};
soc {
usb2@60f8800 {
status = "okay";
};
usb3@8af8800 {
status = "okay";
};
};
};
&usb3_hs_phy {
status = "okay";
};
&usb2_hs_phy {
status = "okay";
};

View File

@ -0,0 +1,12 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019-orbi.dtsi"
/ {
model = "NETGEAR SRR60";
compatible = "netgear,srr60";
chosen {
bootargs = "root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_1)ro,256K(0:CDT)ro,256K(0:CDT_1)ro,512K(0:BOOTCONFIG1)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_1)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,64K(cert)ro,3840K(kernel-2)ro,31488K(rootfs-2)ro,35328K@44881K(firmware-2)ro,5M(device_table)ro,17M(cp_file)ro,102737K(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait";
};
};

View File

@ -0,0 +1,12 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qcom-ipq4019-orbi.dtsi"
/ {
model = "NETGEAR SRS60";
compatible = "netgear,srs60";
chosen {
bootargs = "root=/dev/mmcblk0p20 blkdevparts=mmcblk0:512K@17K(0:SBL1)ro,512K(0:BOOTCONFIG)ro,512K(0:QSEE)ro,512K(0:QSEE_1)ro,256K(0:CDT)ro,256K(0:CDT_1)ro,512K(0:BOOTCONFIG1)ro,256K(0:APPSBLENV)ro,1M(0:APPSBL)ro,1M(0:APPSBL_1)ro,256K(0:ART)ro,256K(ARTMTD)ro,2M(language)ro,256K(config)ro,256K(pot)ro,256K(traffic_meter)ro,256K(pot_bak)ro,256K(traffic_meter.bak)ro,3840K(kernel),31488K(rootfs),35328K@9233K(firmware),256K(mtdoops)ro,64K(cert)ro,3840K(kernel-2)ro,31488K(rootfs-2)ro,35328K@44881K(firmware-2)ro,5M(device_table)ro,17M(cp_file)ro,102737K(reserved)ro,-(unallocated) rootfstype=squashfs,ext4 rootwait";
};
};

View File

@ -646,6 +646,64 @@ define Device/netgear_ex6150v2
endef endef
TARGET_DEVICES += netgear_ex6150v2 TARGET_DEVICES += netgear_ex6150v2
define Device/netgear_orbi
$(call Device/DniImage)
SOC := qcom-ipq4019
DEVICE_VENDOR := NETGEAR
IMAGE/factory.img := append-kernel | pad-offset 128k 64 | \
append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
append-rootfs | pad-rootfs | netgear-dni
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct e2fsprogs kmod-fs-ext4 losetup
endef
define Device/netgear_rbx50
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765352+0+4000+512+2x2+2x2+4x4
KERNEL_SIZE := 3932160
ROOTFS_SIZE := 32243712
IMAGE_SIZE := 36175872
endef
define Device/netgear_rbr50
$(call Device/netgear_rbx50)
DEVICE_MODEL := RBR50
DEVICE_VARIANT := v1
NETGEAR_BOARD_ID := RBR50
endef
TARGET_DEVICES += netgear_rbr50
define Device/netgear_rbs50
$(call Device/netgear_rbx50)
DEVICE_MODEL := RBS50
DEVICE_VARIANT := v1
NETGEAR_BOARD_ID := RBS50
endef
TARGET_DEVICES += netgear_rbs50
define Device/netgear_srx60
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765352+0+4096+512+2x2+2x2+4x4
KERNEL_SIZE := 3932160
ROOTFS_SIZE := 32243712
IMAGE_SIZE := 36175872
endef
define Device/netgear_srr60
$(call Device/netgear_srx60)
DEVICE_MODEL := SRR60
NETGEAR_BOARD_ID := SRR60
endef
TARGET_DEVICES += netgear_srr60
define Device/netgear_srs60
$(call Device/netgear_srx60)
DEVICE_MODEL := SRS60
NETGEAR_BOARD_ID := SRS60
endef
TARGET_DEVICES += netgear_srs60
define Device/netgear_wac510 define Device/netgear_wac510
$(call Device/FitImage) $(call Device/FitImage)
$(call Device/UbiFit) $(call Device/UbiFit)

View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile --- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile
@@ -902,11 +902,61 @@ dtb-$(CONFIG_ARCH_QCOM) += \ @@ -902,11 +902,65 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \ qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \ qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \ qcom-apq8084-mtp.dtb \
@ -47,18 +47,22 @@ Signed-off-by: John Crispin <john@phrozen.org>
qcom-ipq4019-ap.dk07.1-c2.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \ + qcom-ipq4019-a62.dtb \
+ qcom-ipq4019-cm520-79f.dtb \ + qcom-ipq4019-cm520-79f.dtb \
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \
+ qcom-ipq4019-ea8300.dtb \ + qcom-ipq4019-ea8300.dtb \
+ qcom-ipq4019-eap2200.dtb \ + qcom-ipq4019-eap2200.dtb \
+ qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \
+ qcom-ipq4019-fritzrepeater-1200.dtb \ + qcom-ipq4019-fritzrepeater-1200.dtb \
+ qcom-ipq4019-fritzrepeater-3000.dtb \ + qcom-ipq4019-fritzrepeater-3000.dtb \
+ qcom-ipq4019-habanero-dvk.dtb \
+ qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-map-ac2200.dtb \
+ qcom-ipq4019-mr8300.dtb \ + qcom-ipq4019-mr8300.dtb \
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \
+ qcom-ipq4019-habanero-dvk.dtb \
+ qcom-ipq4019-pa2200.dtb \ + qcom-ipq4019-pa2200.dtb \
+ qcom-ipq4019-rbr50.dtb \
+ qcom-ipq4019-rbs50.dtb \
+ qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-rtl30vw.dtb \
+ qcom-ipq4019-srr60.dtb \
+ qcom-ipq4019-srs60.dtb \
+ qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-u4019-32m.dtb \
+ qcom-ipq4019-wpj419.dtb \ + qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4019-wtr-m2133hp.dtb \ + qcom-ipq4019-wtr-m2133hp.dtb \

View File

@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile --- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile
@@ -837,11 +837,61 @@ dtb-$(CONFIG_ARCH_QCOM) += \ @@ -837,11 +837,65 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \ qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \ qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \ qcom-apq8084-mtp.dtb \
@ -58,7 +58,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4019-e2600ac-c2.dtb \ + qcom-ipq4019-e2600ac-c2.dtb \
+ qcom-ipq4019-habanero-dvk.dtb \ + qcom-ipq4019-habanero-dvk.dtb \
+ qcom-ipq4019-pa2200.dtb \ + qcom-ipq4019-pa2200.dtb \
+ qcom-ipq4019-rbr50.dtb \
+ qcom-ipq4019-rbs50.dtb \
+ qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-rtl30vw.dtb \
+ qcom-ipq4019-srr60.dtb \
+ qcom-ipq4019-srs60.dtb \
+ qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-u4019-32m.dtb \
+ qcom-ipq4019-wpj419.dtb \ + qcom-ipq4019-wpj419.dtb \
+ qcom-ipq4019-wtr-m2133hp.dtb \ + qcom-ipq4019-wtr-m2133hp.dtb \