ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-03 04:26:55 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
f2f428c699
openwrt/package/boot/uboot-envtools/files/qualcommax_ipq60xx

33 lines
690 B
Plaintext
Raw Normal View History

qualcommax: ipq60xx: Add 8devices Mango DVK 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-01-22 09:28:32 +00:00
[ -e /etc/config/ubootenv ] && exit 0
touch /etc/config/ubootenv
. /lib/uboot-envtools.sh
. /lib/functions.sh
board=$(board_name)
case "$board" in
8devices,mango-dvk|\
8devices,mango-dvk-sfp)
idx="$(find_mtd_index 0:APPSBLENV)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
;;
qualcommax: ipq60xx: add support for netgear wax214 Netgear WAX214 is a 802.11 ax dual-band AP with PoE. (similar to Engenius EWS357APV3) Specifications: • CPU: Qualcomm IPQ6010 Quad core Cortex-A53 • RAM: 512MB of DDR3 • Storage: 128MB NAND (Macronix MX30UF1G18AC) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WIFI: 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 4 x GPIO-controlled LEDs - 1 Power LED (orange) - 1 LAN LED (blue) - 1 WIFI 5g LED (blue) - 1 WIFI 2g LED (blue) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An populated serial header is onboard, format is 1.25mm 4p (DF13A-4P-1.25H) RX/TX is working, bootwait is active, secure boot is not enabled. The root password of the stock firmware is unknown, but failsafe mode can be entered to reset the password. Installation Instructions: - obtain serial access - stop auto boot (press "4", Entr boot command line interface) - setenv active_fw 0 (to boot from the primary rootfs, or set to 1 to boot from the secondary rootfs partition) - saveenv - tftpboot the initramfs image - bootm - copy openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi to the device - write the image to the NAND: - cat /proc/mtd and look for rootfs partition (should be mtd11, or mtd12 if you choose active_fw 1) - ubiformat /dev/mtd11 -f -y openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi - reboot Note: the firmware is senao-based. But I was unable to build a valid senao-header into the image. Maybe they changed the header format and senaoFW isn't working any more. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-03-03 15:00:46 +00:00
netgear,wax214)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
;;
qualcommax: ipq60xx: add yuncore fap650 support This commit adds support for the Yuncore FAP650 device. Specifications: - Qualcomm IPQ6018+QCA8075+QCN5022+QCN5052 - 512 MB of RAM (DDR3) - 8 MB of serial flash (SPI NOR) - 128 MB of parallel flash (NAND) - 2x2 2.4 GHz WiFi (IPQ6010) - 2x2 5 GHz WiFi (IPQ6010) - 2x 2dBi 2.4G MIMO antenna - 2x 3dBi 5.8G MIMO antenna - 5x 1 Gbps Ethernet (QCA8075) - POE: 48V (IEEE 802.3af) - power: 12V (~1.5A) - 1x passthru port (rj45 - rj45) - 1x cisco rj45 console port - size: 160mm*86mm*29mm BACKUP YOUR STOCK FIRMWARE: ``` export device=fap650 mkdir -p /tmp/fw_dump_$device cd /tmp/fw_dump_$device dmesg > dmesg_$device.log dtc -I fs /sys/firmware/devicetree/base > $device.dts cat /proc/device-tree/model > model cat /proc/mtd > proc_mtd while read p; do mtd_dev=$(echo $p | cut -d: -f1) echo $mtd_dev dd if=/dev/$mtd_dev of=$mtd_dev done < proc_mtd md5sum * > md5sum.log tar -cvzf ../$device.tar.gz . export sum=$(md5sum /tmp/$device.tar.gz | cut -d' ' -f1) mv ../$device.tar.gz /tmp/${device}_${sum}.tar.gz echo fw backup saved to: /tmp/${device}_${sum}.tar.gz ``` Upload your backup via tftp to the safe place. INSTALLATION: 1. stock firmware web ui Rename factory.bin fw image file to factory.ubin. Flash this image like ordinary stock fw upgrade. 2. stock firmware telnet method Enter telnet cli (login: root, password: 476t*_f0%g09y) and upload factory.bin fw image and rename it to factory.ubin `cd /tmp && wget <your_web_server_ip>/factory.ubin` `sysupgrade factory.ubin 3. initramfs method Put imitramfs image to your TFTP server and rename it for example to fap650.initram Enable serial console and enter to the u-boot cli. Exec these commands: `tftpboot <your_tftp_server_ip>:fap650.initram` `dhcp` When downloading is finished: `bootm` After booting the device, you need to upload to the device factory.ubi fw image. ``` cd /tmp && wget <your_web_server_ip>/factory.ubi` export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1) export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1) ubiformat /dev/${rootfs} -y -f factory.ubi ubiformat /dev/${rootfs_1} -y -f factory.ubi reboot ``` 4. u-boot factory.ubi image method Put factory.ubi to your TFTP server Enter u-boot cli and exec these commands: `tftpboot <your_tftp_server_ip>:factory.ubi` `dhcp` After downloading is finished: `flash rootfs` `flash rootfs_1` `reset` STOCK FIRMWARE RECOVERY: Boot initramfs image. Upload your rootfs mtd partition to the device using scp or download it from the device using wget. Enter device ssh cli and exec: ``` cd /tmp && wget <your_web_server_ip>/rootfs_mtd` export rootfs=$(cat /proc/mtd | grep rootfs | cut -d: -f1) export rootfs_1=$(cat /proc/mtd | grep rootfs_1 | cut -d: -f1) ubiformat /dev/${rootfs} -y -f /tmp/rootfs_mtd ubiformat /dev/${rootfs_1} -y -f /tmp/rootfs_mtd reboot ``` Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
2024-02-28 07:53:54 +00:00
yuncore,fap650)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
;;
qualcommax: ipq60xx: Add 8devices Mango DVK 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-01-22 09:28:32 +00:00
esac
config_load ubootenv
config_foreach ubootenv_add_app_config
exit 0
Reference in New Issue Copy Permalink