openwrt/package/boot/uboot-envtools/files/qualcommax_ipq60xx

[ -e /etc/config/ubootenv ] && exit 0

touch /etc/config/ubootenv

. /lib/uboot-envtools.sh
. /lib/functions.sh

board=$(board_name)

case "$board" in
8devices,mango-dvk|\
8devices,mango-dvk-sfp)
	idx="$(find_mtd_index 0:APPSBLENV)"
	[ -n "$idx" ] && \
		ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
	;;
netgear,wax214)
	idx="$(find_mtd_index 0:appsblenv)"
	[ -n "$idx" ] && \
		ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
	;;
esac

config_load ubootenv
config_foreach ubootenv_add_app_config

exit 0
qualcommax: ipq60xx: Add 8devices Mango DVK 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com> 2024-01-22 09:28:32 +00:00			`[ -e /etc/config/ubootenv ] && exit 0`

			`touch /etc/config/ubootenv`

			`. /lib/uboot-envtools.sh`
			`. /lib/functions.sh`

			`board=$(board_name)`

			`case "$board" in`
			`8devices,mango-dvk\|\`
			`8devices,mango-dvk-sfp)`
			`idx="$(find_mtd_index 0:APPSBLENV)"`
			`[ -n "$idx" ] && \`
			`ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"`
			`;;`
qualcommax: ipq60xx: add support for netgear wax214 Netgear WAX214 is a 802.11 ax dual-band AP with PoE. (similar to Engenius EWS357APV3) Specifications: • CPU: Qualcomm IPQ6010 Quad core Cortex-A53 • RAM: 512MB of DDR3 • Storage: 128MB NAND (Macronix MX30UF1G18AC) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WIFI: 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 4 x GPIO-controlled LEDs - 1 Power LED (orange) - 1 LAN LED (blue) - 1 WIFI 5g LED (blue) - 1 WIFI 2g LED (blue) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An populated serial header is onboard, format is 1.25mm 4p (DF13A-4P-1.25H) RX/TX is working, bootwait is active, secure boot is not enabled. The root password of the stock firmware is unknown, but failsafe mode can be entered to reset the password. Installation Instructions: - obtain serial access - stop auto boot (press "4", Entr boot command line interface) - setenv active_fw 0 (to boot from the primary rootfs, or set to 1 to boot from the secondary rootfs partition) - saveenv - tftpboot the initramfs image - bootm - copy openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi to the device - write the image to the NAND: - cat /proc/mtd and look for rootfs partition (should be mtd11, or mtd12 if you choose active_fw 1) - ubiformat /dev/mtd11 -f -y openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi - reboot Note: the firmware is senao-based. But I was unable to build a valid senao-header into the image. Maybe they changed the header format and senaoFW isn't working any more. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> 2024-03-03 15:00:46 +00:00			`netgear,wax214)`
			`idx="$(find_mtd_index 0:appsblenv)"`
			`[ -n "$idx" ] && \`
			`ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"`
			`;;`
qualcommax: ipq60xx: Add 8devices Mango DVK 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com> 2024-01-22 09:28:32 +00:00			`esac`

			`config_load ubootenv`
			`config_foreach ubootenv_add_app_config`

			`exit 0`