openwrt/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt

2446 lines
58 KiB
Plaintext
Raw Normal View History

config ATH79_MACH_A60
bool "OpenMesh A40/A60 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_USB
config ATH79_MACH_WI2A_AC200I
bool "Nokia WI2A-AC200i support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_NFC
select ATH79_DEV_WMAC
select ATH79_DEV_USB
config ATH79_MACH_ALFA_AP120C
bool "ALFA Network AP120C board support"
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_AP121F
bool "ALFA Network AP121F support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ALFA_AP96
bool "ALFA Network AP96 board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_HORNET_UB
bool "ALFA Network Hornet-UB board support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ALFA_NX
bool "ALFA Network N2/N5 board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_TUBE2H
bool "ALFA Network Tube2H board support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_SC1750
bool "Abicom SC1750 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_SC300M
bool "Abicom SC300M board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_SC450
bool "Abicom SC450 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ALL0258N
bool "Allnet ALL0258N support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_ALL0315N
bool "Allnet ALL0315N support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_ANTMINER_S1
bool "Bitmain Antminer S1 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ANTMINER_S3
bool "Bitmain Antminer S3 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ANTROUTER_R1
bool "Bitmain Antrouter R1 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ARDUINO_YUN
bool "Arduino Yun"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_AP132
bool "Atheros AP132 reference board"
select SOC_QCA955X
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_AP143
bool "Atheros AP143 reference board"
select SOC_QCA953X
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_SPI
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_DEV_ETH
select ATH79_DEV_M25P80
config ATH79_MACH_AP147
bool "Atheros AP147 reference board"
select SOC_QCA953X
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_DEV_AP9X_PCI if PCI
config ATH79_MACH_AP152
bool "Atheros AP152 reference board"
select SOC_QCA956X
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_DEV_AP9X_PCI if PCI
config ATH79_MACH_AP531B0
bool "Rockeetech AP531B0 support"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_SPI
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_AP90Q
bool "YunCore AP80Q/AP90Q support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_AP91_5G
bool "ALFA Network AP91-5G support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_AP96
bool "Atheros AP96 board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_PB42
bool "Atheros PB42 board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_M25P80
config ATH79_MACH_C55
bool "AirTight Networks C-55 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_C60
bool "AirTight Networks C-60 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_NFC
select ATH79_DEV_USB
config ATH79_MACH_AW_NR580
bool "AzureWave AW-NR580 board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_F9K1115V2
bool "Belkin AC1750DB board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_EPG5000
bool "EnGenius EPG5000 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_ESR1750
bool "EnGenius ESR1750 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_PQI_AIR_PEN
bool "PQI Air Pen"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_SOM9331
bool "SOM9331 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
config ATH79_MACH_SR3200
bool "YunCore SR3200 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_BHR_4GRV2
bool "Buffalo BHR-4GRV2 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_WHR_HP_G300N
bool "Buffalo WHR-HP-G300N board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_WLAE_AG300N
bool "Buffalo WLAE-AG300N board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_WLR8100
bool "Sitecom WLR-8100 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WZR_HP_AG300H
bool "Buffalo WZR-HP-AG300H board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_WZR_HP_G300NH
bool "Buffalo WZR-HP-G300NH board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select RTL8366_SMI
config ATH79_MACH_WZR_HP_G300NH2
bool "Buffalo WZR-HP-G300NH2 board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_WZR_HP_G450H
bool "Buffalo WZR-HP-G450H board support"
select SOC_AR724X
select ATH79_DEV_ETH
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_WZR_450HP2
bool "Buffalo WZR-450HP2 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WP543
bool "Compex WP543/WPJ543 board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select MYLOADER
config ATH79_MACH_WPE72
bool "Compex WPE72/WPE72NX board support"
select SOC_AR724X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select MYLOADER
config ATH79_MACH_WPJ342
bool "Compex WPJ342 board support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WPJ344
bool "Compex WPJ344 board support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WPJ531
bool "Compex WPJ531 board support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WPJ558
bool "Compex WPJ558 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WPJ563
bool "Compex WPJ563 board support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
config ATH79_MACH_XD3200
bool "YunCore XD3200 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_DGL_5500_A1
bool "D-Link DGL-5500 A1 support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_USB
config ATH79_MACH_DHP_1565_A1
bool "D-Link DHP-1565 rev. A1 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_DIR_505_A1
bool "D-Link DIR-505-A1 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_DIR_600_A1
bool "D-Link DIR-600 A1/DIR-615 E1/DIR-615 E4 support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_NVRAM
config ATH79_MACH_DIR_615_C1
bool "D-Link DIR-615 rev. C1 support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_DIR_615_I1
bool "D-Link DIR-615 rev. I1 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_DIR_825_B1
bool "D-Link DIR-825 rev. B1 board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_DIR_825_C1
bool "D-Link DIR-825 rev. C1/DIR-835 rev. A1 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_DIR_869_A1
bool "D-Link DIR-869 rev. A1"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_DLAN_HOTSPOT
bool "devolo dLAN Hotspot support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_DLAN_PRO_500_WP
bool "devolo dLAN pro 500 Wireless+ support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_SPI
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_USB
config ATH79_MACH_DLAN_PRO_1200_AC
bool "devolo dLAN pro 1200+ WiFi ac support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_SPI
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_NFC
select ATH79_DEV_USB
config ATH79_MACH_DOMYWIFI_DW33D
bool "DomyWifi DW33D support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_NFC
select ATH79_DEV_WMAC
select ATH79_DEV_USB
config ATH79_MACH_DR342
bool "Wallys DR342 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_DR344
bool "Wallys DR344 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_DR531
bool "Wallys DR531 board support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_DRAGINO2
bool "DRAGINO V2 support"
select SOC_AR933X
select ATH79_DEV_M25P80
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_WMAC
select ATH79_DEV_ETH
select ATH79_DEV_USB
ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2 WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334. Specification: - 750/400/250 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) - 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 1x USB 2.0 - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 2-pos switch - 1x DC jack for main power input (9-48 V) - UART (J5) and LEDs (J13) headers on PCB WHQX E600G is based on Qualcomm QCA9531. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) - 2x 10/100 Mbps Ethernet - 6x LED (1x RGB, 5 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-12 V) - UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB Important notice: First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data! Flash instruction (using U-Boot CLI and tftp server): 1. Configure PC with static IP 192.168.1.10 and tftp server. 2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. 3. Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. 4. Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): 1. Configure PC with static IP 192.168.1.xxx(2-254)/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. 3. Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: Peng Zhang <sd20@qxwlan.com> [reworked: image generation code, mach-* files, commit description, fixed minor code style issues, rebased on master] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-05 09:38:05 +00:00
config ATH79_MACH_E1700AC_V2
bool "Qxwlan E1700AC v2 support"
ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2 WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334. Specification: - 750/400/250 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) - 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 1x USB 2.0 - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 2-pos switch - 1x DC jack for main power input (9-48 V) - UART (J5) and LEDs (J13) headers on PCB WHQX E600G is based on Qualcomm QCA9531. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) - 2x 10/100 Mbps Ethernet - 6x LED (1x RGB, 5 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-12 V) - UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB Important notice: First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data! Flash instruction (using U-Boot CLI and tftp server): 1. Configure PC with static IP 192.168.1.10 and tftp server. 2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. 3. Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. 4. Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): 1. Configure PC with static IP 192.168.1.xxx(2-254)/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. 3. Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: Peng Zhang <sd20@qxwlan.com> [reworked: image generation code, mach-* files, commit description, fixed minor code style issues, rebased on master] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-05 09:38:05 +00:00
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_E2100L
bool "Linksys E2100L board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_E558_V2
bool "Qxwlan E558 v2 support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2 WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334. Specification: - 750/400/250 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) - 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 1x USB 2.0 - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 2-pos switch - 1x DC jack for main power input (9-48 V) - UART (J5) and LEDs (J13) headers on PCB WHQX E600G is based on Qualcomm QCA9531. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) - 2x 10/100 Mbps Ethernet - 6x LED (1x RGB, 5 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-12 V) - UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB Important notice: First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data! Flash instruction (using U-Boot CLI and tftp server): 1. Configure PC with static IP 192.168.1.10 and tftp server. 2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. 3. Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. 4. Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): 1. Configure PC with static IP 192.168.1.xxx(2-254)/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. 3. Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: Peng Zhang <sd20@qxwlan.com> [reworked: image generation code, mach-* files, commit description, fixed minor code style issues, rebased on master] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-05 09:38:05 +00:00
config ATH79_MACH_E600G_V2
bool "Qxwlan E600G/E600GAC v2 support"
ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2 WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334. Specification: - 750/400/250 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11) - 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11) - 2x 10/100/1000 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 1x USB 2.0 - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 2-pos switch - 1x DC jack for main power input (9-48 V) - UART (J5) and LEDs (J13) headers on PCB WHQX E600G is based on Qualcomm QCA9531. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601) - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-48 V) - UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 64/128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11) - 2x 10/100 Mbps Ethernet - 6x LED (1x RGB, 5 driven by GPIO) - 1x button (reset) - 1x DC jack for main power input (9-12 V) - UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB Important notice: First version of these boards are using different mtd layout, with ART data at the end. You should not use v2 images on v1 board because it will result in lost of ART data! Flash instruction (using U-Boot CLI and tftp server): 1. Configure PC with static IP 192.168.1.10 and tftp server. 2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. 3. Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. 4. Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): 1. Configure PC with static IP 192.168.1.xxx(2-254)/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. 3. Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: Peng Zhang <sd20@qxwlan.com> [reworked: image generation code, mach-* files, commit description, fixed minor code style issues, rebased on master] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-05 09:38:05 +00:00
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_E750A_V4
bool "Qxwlan E750A v4 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_E750G_V8
bool "Qxwlan E750G v8 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ESR900
bool "EnGenius ESR900 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_EW_BALIN
bool "embedded wireless Balin Platform support"
select SOC_AR934X
select ATH79_DEV_M25P80
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_WMAC
select ATH79_DEV_ETH
select ATH79_DEV_USB
select ATH79_DEV_AP9X_PCI if PCI
config ATH79_MACH_EW_DORIN
bool "embedded wireless Dorin Platform support"
select SOC_AR933X
select ATH79_DEV_M25P80
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_WMAC
select ATH79_DEV_ETH
config ATH79_MACH_EL_M150
bool "EasyLink EL-M150 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_EL_MINI
bool "EasyLink EL-MINI support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_AR150
bool "GL AR150 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_AR300
bool "GL_AR300 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_AR300M
bool "GL_AR300M support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_AR750
bool "GL.iNet GL-AR750 support"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_AR750S
bool "GL.iNet GL-AR750S support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_DOMINO
bool "DOMINO support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_MIFI
bool "GL MIFI support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_INET
bool "GL-INET support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GL_USB150
bool "GL.iNet GL-USB150 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_EAP120
bool "TP-LINK EAP120 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
ar71xx: add support for EnGenius ENS202EXT EnGenius ENS202EXT is an outdoor wireless access point with 2-port 10/100 switch, detachable antennas and proprietery PoE. The device is based on Qualcomm/Atheros AR9341 v1. Specifications: - 535/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM - 16 MB of FLASH - UART (J1) header on PCB (unpopulated) - 2x 10/100 Mbps Ethernet - 2.4 GHz, up to 26dBm - 2x external, detachable antennas - 7x LED, 1x button Flash instructions: You have three options: - Use the vendor firmware upgrade page on the web interface and give it the factory.img. This is the easiest way to go about it. - If you have serial access during u-boot, interrupt the normal boot (any key before timeout) and run 'run failsafe_boot'; this will bring you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've bricked the normal firmware. - Use the vendor's management cli, which can be accessed via telnet with the same credentials as the web login (default admin:admin), then issue the following commands: *** Hi admin, welcome to use cli(V-1.6.7) *** ---========= Commands Help =========--- stat -- Status sys -- System wless2 -- 2.4G-Wireless mgmt -- Management tree -- Tree help -- Help reboot -- Reboot ens202ext>mgmt Management ---========= Commands Help =========--- admin -- Administration mvlan -- Management VLAN settings snmp -- SNMP settings backup -- Backup/Restore settings autorb -- Auto reboot settings fwgrade -- Firmware upgrade time -- Time settings wifisch -- Wifi schedule log -- Log diag -- Diagnostics disc -- Device Discovery logout -- Logout help -- Help exit -- Exit ens202ext/mgmt>fwgrade Management --> Firmware upgrade ---========= Commands Help =========--- fwup -- Firmware upgrade help -- Help exit -- Exit ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2017-04-14 17:08:17 +00:00
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_ENS202EXT
bool "EnGenius ENS202EXT support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_EAP300V2
bool "EnGenius EAP300 v2 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_GS_OOLITE_V1
bool "GainStrong Oolite/Minibox V1.0 support"
select SOC_AR933X
select ARH79_DEV_ETH
select ARH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_GS_OOLITE_V5_2
bool "GainStrong Oolite V5.2 support"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_HIVEAP_121
bool "Aerohive HiveAP-121 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_HIWIFI_HC6361
bool "HiWiFi HC6361 board support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_JA76PF
bool "jjPlus JA76PF board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_JWAP003
bool "jjPlus JWAP003 board support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_JWAP230
bool "jjPlus JWAP230 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_KOALA
bool "OCEDO Koala board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_ETH
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
ar71xx: add support for Samsung WAM250 Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless hub, dedicated for Samsung Shape Wireless Audio System. The device is based on Atheros AR9344. FCC ID: A3LWAM250. Specification: - 560/450/225 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet - 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA - 1x USB 2.0 - 4x LED (all are driven by GPIO) - 2x button (reset, wps/speaker add) - DC jack for main power input (14 V) - UART header on PCB (J4, RX: 3, TX: 5) Flash instruction: This device uses dual-image (switched between upgrades) with a common jffs2 config partition. Fortunately, there is a way to disable this mode so that more flash space can be used by OpenWrt image. You can easily access this device over telnet, using root/root credentials (the same also work for serial console access). 1. Make sure that your device uses second (bootpart=2) image using command: "fw_printenv bootpart". 2. If your device uses first image (bootpart=1), perform upgrade to the latest vendor firmware (after the update, device should boot from second partition) using web gui (default login: admin/1234567890). 3. Rename "sysupgrade" image to "firmware.bin", download it (you can use wget, tftp or ftpget) to "/tmp" and issue below commands: mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}') mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin) fw_setenv bootpart fw_setenv bootcmd "bootm 0x9f070000" reboot Revert to vendor firmware instruction: 1. Download vendor firmware to "/tmp" device and issue below commands: fw_setenv bootpart 1 sysupgrade -n -F SS_BHUB_v2.2.05.bin Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-08 21:28:07 +00:00
config ATH79_MACH_WAM250
bool "Samsung WAM250 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WIFI_PINEAPPLE_NANO
bool "Hak5 WiFi Pineapple NANO support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WRT160NL
bool "Linksys WRT160NL board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_WRT400N
bool "Linksys WRT400N board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_WRTNODE2Q
bool "WRTnode2Q board support"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_R36A
bool "ALFA Network R36A support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:54:08 +00:00
config ATH79_MACH_R602N
bool "P&W R602N support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_R6100
bool "NETGEAR R6100 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_MC_MAC1200R
bool "MERCURY MAC1200R board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_RB4XX
bool "MikroTik RouterBOARD 4xx series support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_USB
config ATH79_MACH_RB750
bool "MikroTik RouterBOARD 750 support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_USB
select ATH79_ROUTERBOOT
config ATH79_MACH_RB91X
bool "MikroTik RouterBOARD 91X support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_SPI
select ATH79_DEV_WMAC
select ATH79_DEV_USB
select ATH79_ROUTERBOOT
config ATH79_MACH_RB922
bool "MikroTik RouterBOARD 922 support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_M25P80
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_ROUTERBOOT
select RLE_DECOMPRESS
config ATH79_MACH_RB95X
bool "MikroTik RouterBOARD 95X support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_NFC
select ATH79_DEV_WMAC
select ATH79_DEV_USB
select ATH79_ROUTERBOOT
config ATH79_MACH_RB2011
bool "MikroTik RouterBOARD 2011 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_M25P80
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_ROUTERBOOT
config ATH79_MACH_RBSPI
bool "MikroTik RouterBOARD SPI-NOR support"
select SOC_AR934X
select SOC_QCA953X
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_ROUTERBOOT
help
Say 'Y' here if you want your kernel to support the
ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards The patch adds support for the MikroTik RB911-2Hn (911 Lite2) and the RB911-5Hn (911 Lite5) boards: https://mikrotik.com/product/RB911-2Hn https://mikrotik.com/product/RB911-5Hn The two boards are using the same hardware design, the only difference between the two is the supported wireless band. Specifications: * SoC: Atheros AR9344 (600MHz) * RAM: 64MiB * Storage: 16 MiB SPI NOR flash * Ethernet: 1x100M (Passive PoE in) * Wireless: AR9344 built-in wireless MAC, single chain 802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn) Notes: * Older versions of these boards might be equipped with a NAND flash chip instead of the SPI NOR device. Those boards are not supported (yet). * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the same hardware. Support for that can be added later with little effort probably. Installation: 1. Setup a DHCP/BOOTP Server with the following parameters: * DHCP-Option 66 (TFTP server name): pointing to a local TFTP server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename of the to be booted image. The usable intramfs files are: - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin 2. Press the reset button on the board and keep that pressed. 3. Connect the board to your local network via its ethernet port. 4. Release the button after the LEDs on the board are turned off. Now the board should load and start the initramfs image from the TFTP server. 5. Upload the sysupgrade image to the board with scp: $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin 5. Log in to the running system listening on 192.168.1.1 via ssh as root (without password): $ ssh root@192.168.1.1 7. Flash the uploaded firmware file from the ssh session via the sysupgrade command: root@OpenWrt:~# sysupgrade /tmp/fw.bin Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-18 12:50:32 +00:00
MikroTik ROuterBOARD 911-2Hn (911 Lite2)
MikroTik ROuterBOARD 911-5Hn (911 Lite5)
ar71xx: complete support for RB mAP 2nD This patch adds support for the MikroTik RouterBOARD mAP 2nD https://mikrotik.com/product/RBmAP2nD Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: builtin QCA9531, 2x2:2 - Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2) - USB: microUSB type AB port This patch adds missing code to fully support mAP. Machfile already contained configuration for mAP 2nD, but device specific configuration like LEDs etc., was missing. Note: The POE LED works but doesn't turn on when POE passthrough is enabled, despite being configured with GPIO trigger. Installation 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 11:15:03 +00:00
MikroTik RouterBOARD mAP
MikroTik RouterBOARD mAP lite
ar71xx: add support for MikroTik RB931-2nD This patch adds support for the MikroTik RB931-2nD (hAP mini): https://mikrotik.com/product/RB931-2nD Specifications: * SoC: Qualcomm QCA9533 (650MHz) * RAM: 32MiB * Storage: 16MiB SPI NOR flash * Ethernet: 3x100M * Wireless: QCA9533 built-in, dual-chain 802.11b/g/n Installation: 1. Setup a DHCP/BOOTP Server with the following parameters: * DHCP-Option 66 (TFTP server name): pointing to a local TFTP server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename of the to be booted image. The usable intramfs files are: - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin 2. Press the reset button on the board and keep that pressed. 3. Connect the board to your local network via its Internet port. 4. Release the button after the LEDs on the board are turned off. Now the board should load and start the initramfs image from the TFTP server. 5. Now connect the board via either of its LAN ports (2 or 3). 6. Upload the sysupgrade image to the board with scp: $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin 7. Log in to the running system listening on 192.168.1.1 via ssh as root (without password): $ ssh root@192.168.1.1 8. Flash the uploaded firmware file from the ssh session via the sysupgrade command: root@OpenWrt:~# sysupgrade /tmp/fw.bin Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-12 11:43:36 +00:00
MikroTik RouterBOARD hAP mini
MikroTik RouterBOARD hAP lite
MikroTik RouterBOARD hAP
MikroTik RouterBOARD hAP ac
MikroTik RouterBOARD hAP ac lite
MikroTik RouterBOARD hEX PoE lite
MikroTik RouterBOARD hEX lite
MikroTik RouterBOARD Powerbox
MikroTik RouterBOARD LHG 5
MikroTik RouterBOARD cAP (EXPERIMENTAL)
ar71xx: complete support for RB wAP 2nD This patch adds support for the MikroTik RouterBOARD wAP https://mikrotik.com/product/RBwAP2nD Specifications: - SoC: Qualcomm QCA9533 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9533, 2x2:2 - Ethernet: 1x100M (802.3af/at POE in) This patch adds missing code to fully support wAP. Machfile already contained configuration for wAP 2nD but device specific configuration like LEDs etc. was missing. Installation: 1. Login to the Mikrotik WebUI to backup your licence keys 2. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. Connect the port labeled internet to your local network 4. Keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started LEDE via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-28 10:30:39 +00:00
MikroTik RouterBOARD wAP
ar71x: add support for Mikrotik Routerboard wAP R This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change is based on 3b15eb0 which added support for the wAP 2nD. This change lacks LED support. Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9531, 802.11b/g/n 2x2:2 - Ethernet: 1x100Mbps - Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack - SIM card slot - Mini-PCIe slot Installation: 1. Login to the Mikrotik WebUI to backup your licence key 2. Change the following settings in System->Routerboard->Settings: - Boot device: try ethernet once then NAND - Boot protocol: DHCP - Force Backup Booter: checked 3. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image, e.g. openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf 4. Power off the device 5. If this is the second attempt to boot OpenWRT or the boot device isn't "try ethernet once then NAND," press and hold the reset button while powered off. If this is the first attempt, this step isn't necessary. 6. Power on the device, holding the reset button for 15-20s if already pressed from the previous step. The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started OpenWRT via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT. Revert to RouterOS Use the "rbcfg" package on in OpenWRT: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: David Ehrmann <ehrmann@gmail.com>
2018-06-10 01:33:24 +00:00
MikroTik RouterBOARD wAP R-2nD
config ATH79_MACH_RBSXTLITE
bool "MikroTik RouterBOARD SXT Lite"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_NFC
select ATH79_DEV_WMAC
select ATH79_ROUTERBOOT
config ATH79_MACH_SMART_300
bool "NC-LINK SMART-300 board support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_T830
bool "YunCore T830 support"
select SOC_QCA953X
select ARH79_DEV_ETH
select ARH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TELLSTICK_ZNET_LITE
bool "TellStick ZNet Lite"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WNDAP360
bool "NETGEAR WNDAP360 board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_WNDR3700
bool "NETGEAR WNDR3700 board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_WNDR4300
bool "NETGEAR WNDR3700v4/WNDR4300 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_WNR2000
bool "NETGEAR WNR2000 board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_WNR2000_V3
bool "NETGEAR WNR2000 V3/WNR612 v2/WNR1000 v2/WPN824N board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_WNR2200
bool "NETGEAR WNR2200 board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_WNR2000_V4
bool "NETGEAR WNR2000 V4"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_OM2P
bool "OpenMesh OM2P board support"
select SOC_AR724X
select SOC_AR933X
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_OM5P
bool "OpenMesh OM5P board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_OM5P_AC
bool "OpenMesh OM5P-AC board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_OM5P_ACv2
bool "OpenMesh OM5P-ACv2 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_OMY_G1
bool "OMYlink OMY G1 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_OMY_X1
bool "OMYlink OMY X1 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_ONION_OMEGA
bool "ONION OMEGA support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_MR12
bool "Meraki MR12 board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_MR16
bool "Meraki MR16 board support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_MR18
bool "Meraki MR18 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_NFC
select ATH79_DEV_WMAC
select LEDS_NU801
config ATH79_MACH_MR600
bool "OpenMesh MR600 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_MZK_W04NU
bool "Planex MZK-W04NU board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_MZK_W300NH
bool "Planex MZK-W300NH board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_RE355
bool "TP-LINK RE355 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_RE450
bool "TP-LINK RE450 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_RME_EG200
bool "eTactica EG200 board supprt"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support for Teltonika RUT900 Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-10-15 11:24:02 +00:00
config ATH79_MACH_RUT9XX
bool "Teltonika RUT900 series support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select GPIO_PCA953X
config ATH79_MACH_RW2458N
bool "Redwave RW2458N board support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_CAP324
bool "PowerCloud Systems CAP324 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_CAP4200AG
bool "Senao CAP4200AG support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_CR3000
bool "PowerCloud Systems CR3000 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_CR5000
bool "PowerCloud CR5000 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_MR1750
bool "OpenMesh MR1750 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_MR900
bool "OpenMesh MR900 board support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_EAP7660D
bool "Senao EAP7660D support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_BSB
bool "Smart Electronics Black Swift board"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ARCHER_C25_V1
bool "TP-LINK Archer C25 v1 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_ARCHER_C58_V1
bool "TP-LINK Archer C58 v1 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
ar71xx: add support to TP-Link Archer C59v1 and C60v1 TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-27 21:41:41 +00:00
config ATH79_MACH_ARCHER_C59_V1
bool "TP-LINK Archer C59 v1 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ARCHER_C59_V2
bool "TP-LINK Archer C59 v2 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support to TP-Link Archer C59v1 and C60v1 TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - 8x LED (controled by 74HC595), 3x button - UART header on PCB TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561+QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Currently not working: - Port LAN1 on C59, LAN4 on C60 - WiFi 5GHz (missing ath10k firmware for QCA9886 chip) - Update from oficial web interface ( tplink-saveloader not support "product-info") Flash instruction: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f020000 +$filesize 3. cp.b $fileaddr 0x9f020000 $filesize 4. reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> [Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-27 21:41:41 +00:00
config ATH79_MACH_ARCHER_C60_V1
bool "TP-LINK Archer C60 v1 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_ARCHER_C60_V2
bool "TP-LINK Archer C60 v2 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_ARCHER_C7
bool "TP-LINK Archer C5/C7/TL-WDR4900 v2 board support"
select SOC_QCA955X
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:54:08 +00:00
config ATH79_MACH_CPE505N
bool "P&W CPE505N support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_CPE510
bool "TP-LINK CPE510 support"
select SOC_AR934X
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_CPE830
bool "YunCore CPE830 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_CPE870
bool "YunCore CPE870 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_MR11U
bool "TP-LINK TL-MR11U/TL-MR3040 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_MR13U
bool "TP-LINK TL-MR13U support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_MR3020
bool "TP-LINK TL-MR3020 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_MR3X20
bool "TP-LINK TL-MR3220/3420 support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_TL_MR6400
bool "TP-LINK TL-MR6400 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WAX50RE
bool "TP-LINK TL-WA750/850RE support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA701ND_V2
bool "TP-LINK TL-WA701ND v2 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA7210N_V2
bool "TP-LINK TL-WA7210N v2 support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA801ND_V3
bool "TP-LINK TL-WA801ND v3 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA830RE_V2
bool "TP-LINK TL-WA830RE v2 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA850RE_V2
bool "TP-LINK TL-WA850RE v2 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA855RE_V1
bool "TP-LINK TL-WA855RE V1 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA901ND
bool "TP-LINK TL-WA901ND/TL-WA7510N support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_TL_WA901ND_V2
bool "TP-LINK TL-WA901ND v2 support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WA901ND_V4
bool "TP-LINK TL-WA901ND v4 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WDR3320_V2
bool "TP-LINK TL-WDR3320 v2 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WDR3500
bool "TP-LINK TL-WDR3500 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WDR4300
bool "TP-LINK TL-WDR3600/4300/4310 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WDR6500_V2
bool "TP-LINK TL-WDR6500 v2 board support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR703N
bool "TP-LINK TL-WR703N/TL-WR710N/TL-MR10U support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR720N_V3
bool "TP-LINK TL-WR720N v3/v4 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR741ND
bool "TP-LINK TL-WR741ND support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_TL_WR741ND_V4
bool "TP-LINK TL-WR741ND v4/TL-MR3220 v2 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR802N_V1
bool "TP-LINK TL-WR802N v1 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_TL_WR802N_V2
bool "TP-LINK TL-WR802N v2 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_TL_WR810N
bool "TP-LINK TL-WR810N support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR810N_V2
bool "TP-LINK TL-WR810N v2 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR840N_V2
bool "TP-LINK TL-WR840N v2/v3 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR841N_V1
bool "TP-LINK TL-WR841N v1 support"
select SOC_AR71XX
select ATH79_DEV_DSA
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_TL_WR841N_V8
bool "TP-LINK TL-WR841N/ND v8/TL-MR3420 v2 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR841N_V9
bool "TP-LINK TL-WR841N/ND v9/TL-WR842N/ND v3/TL-WR740N/ND v6 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR902AC_V1
bool "TP-LINK TL-WR902AC v1 support"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR941ND
bool "TP-LINK TL-WR941ND support"
select SOC_AR913X
select ATH79_DEV_DSA
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR941ND_V6
bool "TP-LINK TL-WR941ND v6 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR940N_V4
bool "TP-LINK TL-WR940N v4 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
ar71xx: add support for TP-Link TL-WR942N v1 TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii <serguzhg@gmail.com> [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-08 20:10:05 +00:00
config ATH79_MACH_TL_WR942N_V1
bool "TP-LINK TL-WR942N v1 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_TL_WR1041N_V2
bool "TP-LINK TL-WR1041N v2 support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR1043N_V5
bool "TP-LINK TL-WR1043N v5 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR1043ND
bool "TP-LINK TL-WR1043ND support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR1043ND_V2
bool "TP-LINK TL-WR1043ND v2 support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR1043ND_V4
bool "TP-LINK TL-WR1043ND v4 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TL_WR2543N
bool "TP-LINK TL-WR2543N/ND support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_TS_D084
bool "PISEN TS-D084 support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_TEW_632BRP
bool "TRENDnet TEW-632BRP support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_TEW_673GRU
bool "TRENDnet TEW-673GRU support"
select SOC_AR71XX
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_TEW_712BR
bool "TRENDnet TEW-712BR support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TEW_732BR
bool "TRENDnet TEW-732BR support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_TEW_823DRU
bool "TRENDnet TEW-823DRU support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_UBNT
bool "Ubiquiti AR71xx based boards support"
select SOC_AR71XX
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_UBNT_UNIFIAC
bool "Ubiquiti UniFi AC (LITE/LR/MESH/PRO) support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_USB
config ATH79_MACH_WEIO
bool "WeIO board"
select SOC_AR933X
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_MYNET_N600
bool "WD My Net N600 board support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_MYNET_N750
bool "WD My Net N750 board support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_MYNET_REXT
bool "WD My Net Wi-Fi Range Extender board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_Z1
bool "Meraki Z1 board support"
select SOC_AR934X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select LEDS_NU801
config ATH79_MACH_ZBT_WE1526
bool "Zbtlink ZBT-WE1526 board support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_ZCN_1523H
bool "Zcomax ZCN-1523H support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_N5Q
bool "ALFA Network N5Q support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_WMAC
config ATH79_MACH_NBG460N
bool "Zyxel NBG460N/550N/550NH board support"
select SOC_AR913X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_NBG6716
bool "Zyxel NBG6616/NBG6716 board support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_CARAMBOLA2
bool "8devices Carambola2 board"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_LAN_TURTLE
bool "Hak5 LAN Turtle and Packet Squirrel support"
select SOC_AR933X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
config ATH79_MACH_LIMA
bool "8devices Lima board"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_M25P80
select ATH79_DEV_SPI
select ATH79_DEV_USB
select ATH79_DEV_WMAC
select ATH79_DEV_ETH
config ATH79_MACH_RAMBUTAN
bool "8devices Rambutan board"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_NFC
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E316N_V2
bool "COMFAST CF-E316N v2 support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E320N_V2
bool "COMFAST CF-E320N v2 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E355AC
bool "COMFAST CF-E355AC v1/v2 support"
select SOC_QCA953X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E375AC
bool "COMFAST CF-E375AC support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E380AC_V1
bool "COMFAST CF-E380AC v1 support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E380AC_V2
bool "COMFAST CF-E380AC v2 support"
select SOC_QCA955X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E520N
bool "COMFAST CF-E520N support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_CF_E530N
bool "COMFAST CF-E530N support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_BHU_BXU2000N2_A
bool "BHU BXU2000n-2 rev. A support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_USB
select ATH79_DEV_WMAC
config ATH79_MACH_QIHOO_C301
bool "Qihoo 360 C301 board support"
select SOC_AR934X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_DEV_USB
select ATH79_NVRAM
config ATH79_MACH_DAP_1330_A1
bool "D-Link DAP-1330 rev. A1 support"
select SOC_QCA953X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_DAP_2695_A1
bool "D-Link DAP-2695 rev. A1 support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
select ATH79_NVRAM
config ATH79_MACH_TL_WPA8630
bool "TP-Link TL-WPA8630 support"
select SOC_QCA956X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
config ATH79_MACH_FRITZ300E
bool "AVM FRITZ!WLAN Repeater 300E support"
select SOC_AR724X
select ATH79_DEV_AP9X_PCI if PCI
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
config ATH79_MACH_FRITZ4020
bool "AVM FRITZ!Box 4020 support"
select SOC_QCA956X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_USB
select ATH79_DEV_M25P80
config ATH79_MACH_FRITZ450E
bool "AVM FRITZ!WLAN Repeater 450E support"
select SOC_QCA955X
select ATH79_DEV_ETH
select ATH79_DEV_GPIO_BUTTONS
select ATH79_DEV_LEDS_GPIO
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC