ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-06 05:54:25 +00:00
Code Issues Actions 5 Packages Projects Releases Wiki Activity
b17413117d
openwrt/target/linux/mpc85xx/base-files/etc/board.d/01_leds

27 lines
532 B
Plaintext
Raw Normal View History

mpc85xx: overhaul WS-AP3825i LED setup As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net>
2022-03-24 22:09:24 +00:00
. /lib/functions/leds.sh
. /lib/functions/uci-defaults.sh
board=$(board_name)
boardname="${board##*,}"
board_config_update
case $board in
mpc85xx: correct WS-AP3715i eth LED assignment Ethernet LED assignments were incorrectly swapped. Fix the assignment logic so the correct LED is illuminated for the LAN LEDs. Signed-off-by: David Bauer <mail@david-bauer.net>
2023-09-20 18:59:35 +00:00
enterasys,ws-ap3715i)
ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth0"
ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth1"
;;
mpc85xx: overhaul WS-AP3825i LED setup As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net>
2022-03-24 22:09:24 +00:00
extreme-networks,ws-ap3825i)
ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1"
ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0"
;;
mpc85xx: add support for Hewlett Packard MSM460 Hardware -------- CPU: Freescale P1020 2xe500 PPC RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ") NAND: 128M (Micron 2CA1) BTN: 1x Reset LED: Power - ETH - Radio1 - Radio2 UART: RJ-45 Cisco Pinout - 115200 8N1 Installation ------------ NOTE: You can find a repo with up-to-date instructions as well as the required files here: https://github.com/blocktrron/msm460-flashing Required files ============== You need a command-files as well as a U-Boot image. The command-file has the following content (padded to 131072 bytes). If you copy paste these, remove the newlines! ``` U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin; nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset ``` You can download the required U-Boot from this repository: https://github.com/blocktrron/u-boot-msm/releases Preparation =========== Prepare a TFTP server serving two files: - U-Boot NAND image as `msm460-uboot.bin`. - OpenWrt factory image as `msm460-factory.bin` - Command-file names `commands.tftp` You can start a TFTP server in the current directory using dnsmasq: ```bash sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \ --port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \ --user=root --group=root ``` Replace `enxd0` with the name of your network interface. Procedure ========= 1. Assign yourself the IP-Address 192.168.1.66/24. 3. Connect the Router to the PC while keeping the reset button pressed. 4. The LEDs will eventually begin to flash. They will start to flash faster after around 15 seconds. 5. Release the reset button. 6. Start a new shell 7. Make sure you are currently in the directory where the tftp server is located. 8. Run the following command: ```bash tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999 ``` You get the message "Transfer timed out." To find out if you have been successful, please check the blinking LED Pattern. Signed-off-by: David Bauer <mail@david-bauer.net>
2024-05-30 00:27:50 +00:00
hpe,msm460)
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
;;
mpc85xx: overhaul WS-AP3825i LED setup As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net>
2022-03-24 22:09:24 +00:00
esac
board_config_flush
exit 0
Reference in New Issue Copy Permalink