openwrt/target/linux/mpc85xx/base-files/etc/board.d/01_leds


. /lib/functions/leds.sh
. /lib/functions/uci-defaults.sh

board=$(board_name)
boardname="${board##*,}"

board_config_update

case $board in
enterasys,ws-ap3715i|\
extreme-networks,ws-ap3825i)
	ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1"
	ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0"
	;;
esac

board_config_flush

exit 0
mpc85xx: overhaul WS-AP3825i LED setup As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net> 2022-03-24 22:09:24 +00:00
			`. /lib/functions/leds.sh`
			`. /lib/functions/uci-defaults.sh`

			`board=$(board_name)`
			`boardname="${board##*,}"`

			`board_config_update`

			`case $board in`
mpc85xx: add support for Enterasys WS-AP3715i Hardware -------- SoC: NXP P1010 (1x e500 @ 800MHz) RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9) FLASH: 32M NOR (Spansion S25FL256S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035) UART: 115200 8N1 (RJ-45 Cisco) Installation ------------ 1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in the root directory of a TFTP server and serve it at 192.168.1.66/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Alter the bootcmd in U-Boot: $ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm" $ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000; bootm 0x2000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Boot the initramfs image $ run ramboot_openwrt 5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Signed-off-by: David Bauer <mail@david-bauer.net> 2023-03-18 01:28:23 +00:00			`enterasys,ws-ap3715i\|\`
mpc85xx: overhaul WS-AP3825i LED setup As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net> 2022-03-24 22:09:24 +00:00			`extreme-networks,ws-ap3825i)`
			`ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1"`
			`ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0"`
			`;;`
			`esac`

			`board_config_flush`

			`exit 0`