openwrt/target/linux/mpc85xx/generic/target.mk

BOARDNAME:=Generic
FEATURES+=nand
KERNELNAME:=cuImage.tl-wdr4900-v1

define Target/Description
	Build firmware images for generic MPC85xx based boards.
endef
mpc85xx: Add subtargets Generic and P1020 Only difference between Generic and P1020 is that P1020 enables SMP with two CPUs in the kernel config. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36454 2013-04-26 16:57:43 +00:00			`BOARDNAME:=Generic`
mpc85xx: add support for Sophos RED 15w Rev.1 Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> 2019-01-08 00:20:56 +00:00			`FEATURES+=nand`
mpc85xx: use new build code style The following moves the mpc85xx target (generic & P1020) to the new build code style. Compile & Flash tested on an Aerohive HiveAP-330. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> 2017-10-20 17:36:25 +00:00			`KERNELNAME:=cuImage.tl-wdr4900-v1`
mpc85xx: Add subtargets Generic and P1020 Only difference between Generic and P1020 is that P1020 enables SMP with two CPUs in the kernel config. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36454 2013-04-26 16:57:43 +00:00
			`define Target/Description`
			`Build firmware images for generic MPC85xx based boards.`
			`endef`