ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
2024-02-07 13:48:43 +00:00
|
|
|
#include <dt-bindings/leds/common.h>
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
|
|
|
|
/ {
|
|
|
|
aliases {
|
|
|
|
label-mac-device = &gmac0;
|
2020-09-27 17:40:51 +00:00
|
|
|
led-boot = &led_power_orange;
|
|
|
|
led-failsafe = &led_power_white;
|
|
|
|
led-running = &led_power_white;
|
|
|
|
led-upgrade = &led_net_orange;
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
reset {
|
|
|
|
label = "reset";
|
|
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
|
|
|
label = "wps";
|
|
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
|
|
};
|
|
|
|
};
|
2020-09-27 17:40:51 +00:00
|
|
|
|
|
|
|
leds: leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
led_power_orange: power_orange {
|
2024-02-07 13:48:43 +00:00
|
|
|
function = LED_FUNCTION_POWER;
|
|
|
|
color = <LED_COLOR_ID_ORANGE>;
|
2020-09-27 17:40:51 +00:00
|
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
led_power_white: power_white {
|
2024-02-07 13:48:43 +00:00
|
|
|
function = LED_FUNCTION_POWER;
|
|
|
|
color = <LED_COLOR_ID_WHITE>;
|
2020-09-27 17:40:51 +00:00
|
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
led_net_orange: net_orange {
|
|
|
|
label = "orange:net";
|
|
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
net_white {
|
|
|
|
label = "white:net";
|
|
|
|
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
};
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
&nand {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "Bootloader";
|
|
|
|
reg = <0x0 0x80000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@80000 {
|
|
|
|
label = "config";
|
|
|
|
reg = <0x80000 0x80000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
factory: partition@100000 {
|
|
|
|
label = "factory";
|
|
|
|
reg = <0x100000 0x40000>;
|
|
|
|
read-only;
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
nvmem-layout {
|
|
|
|
compatible = "fixed-layout";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
|
|
reg = <0x0 0x4da8>;
|
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
eeprom_factory_8000: eeprom@8000 {
|
|
|
|
reg = <0x8000 0x4da8>;
|
|
|
|
};
|
|
|
|
|
|
|
|
macaddr_factory_e000: macaddr@e000 {
|
2023-11-08 03:39:00 +00:00
|
|
|
compatible = "mac-base";
|
2023-11-07 23:55:58 +00:00
|
|
|
reg = <0xe000 0x6>;
|
2023-11-08 03:39:00 +00:00
|
|
|
#nvmem-cell-cells = <1>;
|
2023-11-07 23:55:58 +00:00
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
macaddr_factory_e006: macaddr@e006 {
|
|
|
|
reg = <0xe006 0x6>;
|
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
};
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
partition@140000 {
|
|
|
|
label = "config2";
|
|
|
|
reg = <0x140000 0x40000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@180000 {
|
|
|
|
label = "firmware";
|
2021-01-20 17:36:46 +00:00
|
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
|
|
openwrt,padding = <96>;
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
reg = <0x180000 0x2800000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@2980000 {
|
|
|
|
label = "private";
|
|
|
|
reg = <0x2980000 0x2000000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@4980000 {
|
|
|
|
label = "firmware2";
|
|
|
|
reg = <0x4980000 0x2800000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@7180000 {
|
|
|
|
label = "mydlink";
|
|
|
|
reg = <0x7180000 0x600000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@7780000 {
|
|
|
|
label = "reserved";
|
|
|
|
reg = <0x7780000 0x880000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie0 {
|
|
|
|
wifi0: wifi@0,0 {
|
|
|
|
compatible = "mediatek,mt76";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
2023-11-08 03:39:00 +00:00
|
|
|
nvmem-cells = <&macaddr_factory_e000 1>;
|
2023-10-02 02:12:02 +00:00
|
|
|
nvmem-cell-names = "eeprom";
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
ieee80211-freq-limit = <2400000 2500000>;
|
|
|
|
|
|
|
|
led {
|
|
|
|
led-active-low;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie1 {
|
|
|
|
wifi1: wifi@0,0 {
|
|
|
|
compatible = "mediatek,mt76";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
2023-11-08 03:39:00 +00:00
|
|
|
nvmem-cells = <&macaddr_factory_e000 2>;
|
2023-10-02 02:12:02 +00:00
|
|
|
nvmem-cell-names = "eeprom";
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
|
|
|
|
|
|
led {
|
|
|
|
led-active-low;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&gmac0 {
|
2023-11-08 03:39:00 +00:00
|
|
|
nvmem-cells = <&macaddr_factory_e000 0>;
|
2021-04-02 21:50:02 +00:00
|
|
|
nvmem-cell-names = "mac-address";
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
};
|
|
|
|
|
2022-07-05 22:20:32 +00:00
|
|
|
&gmac1 {
|
|
|
|
status = "okay";
|
|
|
|
label = "wan";
|
|
|
|
phy-handle = <ðphy4>;
|
|
|
|
|
|
|
|
nvmem-cells = <&macaddr_factory_e006>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
};
|
|
|
|
|
|
|
|
&mdio {
|
|
|
|
ethphy4: ethernet-phy@4 {
|
|
|
|
reg = <4>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:EB (label)
wan factory 0xe006 *:EE
2.4 factory 0xe000 +1 *:EC
5.0 factory 0xe000 +2 *:ED
Seems like vendor didn't replace the dummy entrys in the calibration data.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 15:39:21 +00:00
|
|
|
&switch0 {
|
|
|
|
ports {
|
|
|
|
port@0 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan4";
|
|
|
|
};
|
|
|
|
|
|
|
|
port@1 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan3";
|
|
|
|
};
|
|
|
|
|
|
|
|
port@2 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan2";
|
|
|
|
};
|
|
|
|
|
|
|
|
port@3 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan1";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&state_default {
|
|
|
|
gpio {
|
|
|
|
groups = "i2c", "uart3", "jtag", "wdt";
|
|
|
|
function = "gpio";
|
|
|
|
};
|
|
|
|
};
|