2018-12-28 08:24:01 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
|
|
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
|
|
|
|
|
|
/ {
|
|
|
|
|
aliases {
|
ath79: provide label MAC address
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-15 13:13:33 +00:00
|
|
|
label-mac-device = ð0;
|
2018-12-28 08:24:01 +00:00
|
|
|
};
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
&pcie {
|
|
|
|
|
status = "okay";
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
&uart {
|
|
|
|
|
status = "okay";
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
&mdio0 {
|
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
|
|
phy-mask = <0>;
|
|
|
|
|
|
|
|
|
|
phy0: ethernet-phy@0 {
|
|
|
|
|
reg = <0>;
|
|
|
|
|
phy-mode = "sgmii";
|
2019-04-14 15:26:04 +00:00
|
|
|
qca,mib-poll-interval = <500>;
|
2018-12-28 08:24:01 +00:00
|
|
|
|
|
|
|
|
qca,ar8327-initvals = <
|
|
|
|
|
0x04 0x00080080 /* PORT0 PAD MODE CTRL */
|
|
|
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
|
|
|
>;
|
|
|
|
|
};
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
ð0 {
|
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
|
|
phy-mode = "sgmii";
|
|
|
|
|
phy-handle = <&phy0>;
|
ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-05 13:44:55 +00:00
|
|
|
|
|
|
|
|
mtd-mac-address = <&mac 0x8>;
|
2018-12-28 08:24:01 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
|
|
&wmac {
|
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
|
|
|
mtd-mac-address = <&mac 0x8>;
|
|
|
|
|
};
|
