openwrt/package/firmware/ipq-wifi/Makefile

166 lines
6.2 KiB
Makefile
Raw Normal View History

firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/version.mk
PKG_NAME:=ipq-wifi
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
PKG_RELEASE:=1
PKG_SOURCE_PROTO:=git
PKG_SOURCE_URL=$(PROJECT_GIT)/project/firmware/qca-wireless.git
PKG_SOURCE_DATE:=2023-03-19
PKG_SOURCE_VERSION:=31ff96d9f99f993cb43d79f0c411fe6bf55633bb
PKG_MIRROR_HASH:=8005a884059925a627024b9022ed06a36ebf4ed7a20e8aab191585afbdd6895f
PKG_FLAGS:=nonshared
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
include $(INCLUDE_DIR)/package.mk
define Build/Compile
endef
ipq40xx: Add support for D-Link DAP-2610 Specifications ============== - SOC: IPQ4018 - RAM: DDR3 256MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11 - 5GHz: IPQ4018, 2x2, front end SKY85717-21 - Ethernet: 1x 10/100/1000Mbps, POE 802.3af - PHY: QCA8072 - UART: GND, blocked, 3.3V, RX, TX / 115200 8N1 - LED: 1x red / green - Button: 1x reset / factory default - U-Boot bootloader with tftp and "emergency web server" accessible using serial port. Installation ============ Flash factory image from D-Link web UI. Constraints in the D-Link web UI makes the factory image unnecessarily large. Flash again using sysupgrade from inside OpenWrt to reclaim some flash space. Return to stock D-Link firmware =============================== Partition layout is preserved, and it is possible to return to the stock firmware simply by downloading it from D-Link and writing it to the firmware partition. # mtd -r write dap2610-firmware.bin firmware Quirks ====== To be flashable from the D-Link http server, the firmware must be larger then 6MB, and the size in the firmware header must match the actual file size. Also, the boot loader verifies the checksum of the firmware before each boot, thus the jffs2 must be after the checksum covered part. This is solved in the factory image by having the rootfs at the very end of the image (without pad-rootfs). The sysupgrade image which does not have to be flashable from the D-Link web UI may be smaller, and the checksum in the firmware header only covers the kernel part of the image. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> [added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux, added emd1's gmac0 config,fix dtc warnings] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-10 09:25:53 +00:00
# Use ath10k-bdencoder from https://github.com/qca/qca-swiss-army-knife.git
# to generate the board-* files here.
#
# This is intended to be used on an interim basis until device-specific
# board data for new devices is available through the upstream compilation
#
# Please send a mail with your device-specific board files upstream.
# You can find instructions and examples on the linux-wireless wiki:
# <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
ALLWIFIBOARDS:= \
8dev_habanero \
8dev_jalapeno \
aruba_ap-365 \
ipq807x: add support for Buffalo WXR-5950AX12 Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ8074A. Specification: - SoC : Qualcomm IPQ8074A - RAM : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK) - Flash : RAW NAND 256 MiB (Winbond W29N02GZBIBA) - WLAN : 2.4/5 GHz (IPQ8074A) - Ethernet : 5 ports - WAN : 100/1000/2500/10000 Mbps x1 (AQR113C) - LAN : 100/1000/2500/10000 Mbps x1 (AQR113C), 10/100/1000 Mbps x3 (QCA8075) - LED/Keys : 8x/5x - UART : pin header on PCB (J7) - assignment: 3.3V, GND, TX, RX from disc marking - settings : 115200n8 - Power : 12 VDC, 4 A Flash instruction using initramfs image: 1. Prepare TFTP server with IP address 192.168.11.10 2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and place it to TFTP directory 3. Hold AOSS (WPS) button and power on WXR-5950AX12 4. WXR-5950AX12 downloads initramfs image from TFTP server and boots with it automatically 5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade 6. Wait ~120 seconds to complete flashing Partition layout: 0x000000000000-0x000000100000 : "0:sbl1" 0x000000100000-0x000000200000 : "0:mibib" 0x000000200000-0x000000280000 : "0:bootconfig" 0x000000280000-0x000000300000 : "0:bootconfig1" 0x000000300000-0x000000600000 : "0:qsee" 0x000000600000-0x000000900000 : "0:qsee_1" 0x000000900000-0x000000980000 : "0:devcfg" 0x000000980000-0x000000a00000 : "0:devcfg_1" 0x000000a00000-0x000000a80000 : "0:apdp" 0x000000a80000-0x000000b00000 : "0:apdp_1" 0x000000b00000-0x000000b80000 : "0:rpm" 0x000000b80000-0x000000c00000 : "0:rpm_1" 0x000000c00000-0x000000c80000 : "0:cdt" 0x000000c80000-0x000000d00000 : "0:cdt_1" 0x000000d00000-0x000000d80000 : "0:appsblenv" 0x000000d80000-0x000000e80000 : "0:appsbl" 0x000000e80000-0x000000f80000 : "0:appsbl_1" 0x000000f80000-0x000001000000 : "0:art" 0x000001000000-0x000001080000 : "0:art_1" 0x000001080000-0x000001100000 : "0:orgdata" 0x000001100000-0x000001180000 : "0:orgdata_1" 0x000001180000-0x000005180000 : "rootfs" 0x000005180000-0x000009180000 : "rootfs_recover" 0x000009180000-0x000010000000 : "user_property" Notes: - WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for normal operation and the 2nd one is for recoverying or firmware upgrading on stock. - Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*" partition when booting. This is just a comparation of hash strings. Behaviors: - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover ---> boot from rootfs - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover ---> boot from rootfs_recover Note: this behavior is used for firmware upgrading on stock - "fw_hash" volume in rootfs is missing ---> boot from rootfs_recover - "fw_hash" volume in rootfs_recover is missing ---> boot from rootfs - "fw_hash" volumes in both root* partition are missing ---> boot from rootfs_recover Reverting to stock firmware: 1. Decrypt official image by buffalo-enc and remove header example of decryption: $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \ -d -k olaffuB -O 0xc8 example of removing header (v3.05): - before $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec 00000000 57 58 52 2d 35 39 35 30 41 58 31 32 5f 33 2e 30 |WXR-5950AX12_3.0| 00000010 35 5f 31 2e 30 31 5f 4a 50 5f 6a 70 5f 71 63 61 |5_1.01_JP_jp_qca| 00000020 0a 66 69 6c 65 6c 65 6e 3d 34 35 33 35 30 39 31 |.filelen=4535091| 00000030 32 0a 55 42 49 23 01 00 00 00 00 00 00 00 00 00 |2.UBI#..........| 00000040 - after $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi 00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............| 00000010 00 00 08 00 00 00 10 00 78 cf c4 91 00 00 00 00 |........x.......| 00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000030 00 00 00 00 00 00 00 00 00 00 00 00 3d 2a 64 fd |............=*d.| 00000040 2. Boot WXR-5950AX12 with OpenWrt initramfs image 3. Upload modified stock image to WXR-5950AX12 4. Find partitions "rootfs" and "rootfs_recover" example: root@OpenWrt:/# cat /proc/mtd dev: size erasesize name ... mtd22: 04000000 00020000 "rootfs" mtd23: 04000000 00020000 "rootfs_recover" ... in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23 5. Format "rootfs"/"rootfs_recover" partition with the uploaded image example: ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi 6. Remove "rootfs"/"rootfs_data" volume from user_property partition example: . /lib/upgrade/nand.sh UBI=$(nand_attach_ubi user_property) ubirmvol /dev/$UBI -N rootfs ubirmvol /dev/$UBI -N rootfs_data 7. Reboot MAC addresses: LAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) WAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) 2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text)) 5 GHz : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text)) Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-23 04:01:13 +00:00
buffalo_wxr-5950ax12 \
ipq40xx: add support for devolo Magic 2 WiFi next SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
2020-10-02 12:32:55 +00:00
devolo_magic-2-wifi-next \
ipq807x: add Dynalink DL-WRX36 Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-08-05 09:38:37 +00:00
dynalink_dl-wrx36 \
edgecore_eap102 \
ipq806x: add Edgecore ECW5410 support This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-07 10:43:37 +00:00
edgecore_ecw5410 \
edgecore_oap100 \
ipq807x: add Edimax CAX1800 Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:17:51 +00:00
edimax_cax1800 \
extreme-networks_ws-ap3915i \
glinet_gl-a1300 \
glinet_gl-ap1300 \
glinet_gl-s1300 \
ipq40xx: Add support for Linksys EA8300 (Dallas) The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-10 15:34:28 +00:00
linksys_ea8300 \
ipq40xx: add support for Linksys WHW03 V2 SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2022-12-23 17:30:36 +00:00
linksys_whw03v2 \
ipq806x: add support for Nokia Airscale AC400i Hardware -------- SoC: Qualcomm IPQ8065 RAM: 512 MB DDR3 Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB) 4 MB SPI-NOR (Macronix MX25U3235F) WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz Qualcomm Atheros QCA9984 - 5Ghz ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt) eth1 - (1000Mbps in both) Auto-negotiation broken on both. USB: USB 2.0 LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red) BTN: Reset Other: SD card slot (non-functional) Serial: 115200bps, near the Ethernet transformers, labeled 9X. Connections from the arrow to the 9X text: [NC] - [TXD] - [GND] - [RXD] - [NC] Installation ------------ 0. Connect to the device Plug your computer into LAN2 (1000Mbps connection required). If you use the LAN1/POE port, set your computer to force a 100Mbps link. Connect to the device via TTL (Serial) 115200n8. Locate the header (or solder pads) labeled 9X, near the Ethernet jacks/transformers. There should be an arrow on the other side of the header marking. The connections should go like this: (from the arrow to the 9X text): NC - TXD - GND - RXD - NC 1. Prepare for installation While the AP is powering up, interrupt the startup process. MAKE SURE TO CHECK YOUR CURRENT PARTITION! If you see: "Current Partition is : partB" or "Need to switch partition from partA to partB", you have to force the device into partA mode, before continuing. This can be done by changing the PKRstCnt to 5 and resetting the device. setenv PKRstCnt 5 saveenv reset After you interrupt the startup process again, you should see: Need to switch partition from partB to partA You can now continue to the next step. If you see: "Current Partition is : partA", you can continue to the next step. 2. Prevent partition switching. To prevent the device from switching partitions, we are going to modify the startup command. set bootcmd "setenv PKRstCnt 0; saveenv; bootipq" setenv 3. First boot Now, we have to boot the OpenWrt intifs. The easiest way to do this is by using Tiny PXE. You can also use the normal U-Boot tftp method. Run "bootp" this will get an IP from the DHCP server and possibly the firmware image. If it doesn't download the firmware image, run "tftpboot". Now run "bootm" to run the image. You might see: "ERROR: new format image overwritten - must RESET the board to recover" this means that the image you are trying to load is too big. Use a smaller image for the initial boot. 4. Install OpenWrt from initfs Once you are booted into OpenWrt, transfer the OpenWrt upgrade image and use sysupgrade to install OpenWrt to the device. Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
2023-02-04 16:00:57 +00:00
nokia_ac400i \
ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0) P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> Signed-off-by: Richard Yu <yurichard3839@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> [Added comment about MIBIB+128 MiB variant. Added commit message section about pcie slot. Renamed gpio-leds' subnodes and added color, function+enum properties.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-12 03:16:21 +00:00
p2w_r619ac \
pakedge_wr-1 \
ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:20:19 +00:00
qnap_301w \
qxwlan_e2600ac-c1 \
qxwlan_e2600ac-c2 \
ipq807x: add Redmi AX6 Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
2022-01-01 22:12:51 +00:00
redmi_ax6 \
ipq40xx: add support for Sony NCP-HG100/Cellular Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac (WiFi-5) wireless function, based on IPQ4019. Specification: - SoC : Qualcomm IPQ4019 - RAM : DDR3 512 MiB (H5TC4G63EFR) - Flash : eMMC 4 GiB (THGBMNG5D1LBAIT) - WLAN : 2.4/5 GHz 2T2R (IPQ4019) - Ethernet : 10/100/1000 Mbps x2 - Transceiver : Qualcomm QCA8072 - WWAN : Telit LN940A9 - Z-Wave : Silicon Labs ZM5101 - Bluetooth : Qualcomm CSR8811 - Audio DAC : Realtek ALC5629 - Audio Amp. : Realtek ALC1304 - Voice Input Processor : Conexant CX20924 - Micro Controller Unit : Nuvoton MINI54FDE - RGB LED, Fan, Temp. sensors - Touch Sensor : Cypress CY8C4014LQI - RGB LED driver : TI LP55231 (2x) - LEDs/Keys : 11x, 6x - UART : through-hole on PCB - J1: 3.3V, TX, RX, GND from tri-angle marking - 115200n8 - Power : 12 VDC, 2.5 A Flash instruction using initramfs image: 1. Prepare TFTP server with the IP address 192.168.132.100 and place the initramfs image to TFTP directory with the name "C0A88401.img" 2. Boot NCP-HG100/Cellular and interrupt after the message "Hit any key to stop autoboot: 2" 3. Perform the following commands and set bootcmd to allow booting from eMMC setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000" saveenv 4. Perform the following command to load/boot the OpenWrt initramfs image tftpboot && bootm 5. On the initramfs image, perform sysupgrade with the sysupgrade image (if needed, backup eMMC partitions by dd command and download to other place before performing sysupgrade) 6. Wait for ~120 seconds to complete flashing Known issues: - There are no drivers for audio-related chips/functions in Linux Kernel and OpenWrt, they cannot be used. - There is no driver for MINI54FDE Micro-Controller Unit, customized for this device by the firmware in the MCU. This chip controls the following functions, but they cannot be controlled in OpenWrt. - RGB LED - Fan this fan is controlled automatically by MCU by default, without driver - Thermal Sensors (2x) - Currently, there is no driver or tool for CY8C4014LQI and cannot be controlled. It cannot be exited from "booting mode" and moved to "normal op mode" after booting. And also, the 4x buttons (mic mute, vol down, vol up, alexa trigger) connected to the IC cannot be controlled. - it can be exited from "booting mode" by installing and executing i2cset command: opkg update opkg install i2c-tools i2cset -y 1 0x14 0xf 1 - There is a connection issue on the control by uqmi for the WWAN module. But modemmanager can be used without any issues and the use of it is recommended. - With the F2FS format, too many errors are reported on erasing eMMC partition "rootfs_data" while booting: [ 1.360270] sdhci: Secure Digital Host Controller Interface driver [ 1.363636] sdhci: Copyright(c) Pierre Ossman [ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO ... [ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 1.528325] mmc0: new HS200 MMC card at address 0001 [ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB [ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB [ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB [ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0) [ 1.550323] Alternate GPT is invalid, using primary GPT. [ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 ... [ 8.841400] mount_root: loading kmods from internal overlay [ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 9.240465] block: attempting to load /etc/config/fstab [ 9.246722] block: unable to load configuration (fstab: Entry not found) [ 9.246863] block: no usable configuration [ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet [ 9.438915] urandom_read: 5 callbacks suppressed [ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read) [ 12.243332] mmc_erase: erase error -110, status 0x800 [ 12.246638] mmc0: cache flush error -110 [ 15.134585] mmc_erase: erase error -110, status 0x800 [ 15.135891] mmc_erase: group start error -110, status 0x0 [ 15.139850] mmc_erase: group start error -110, status 0x0 ...(too many the same errors)... [ 17.350811] mmc_erase: group start error -110, status 0x0 [ 17.356197] mmc_erase: group start error -110, status 0x0 [ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00 [ 17.446910] mmc0: tuning execution failed: -5 [ 17.447111] mmc0: cache flush error -110 [ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint [ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b [ 18.198691] block: attempting to load /etc/config/fstab [ 18.198972] block: unable to load configuration (fstab: Entry not found) [ 18.203029] block: no usable configuration [ 18.211371] mount_root: overlay filesystem has not been fully initialized yet [ 18.214487] mount_root: switching to f2fs overlay So, this support uses ext4 format instead which has no errors. Note: - The primary uart is shared for debug console and Z-Wave chip. The function is switched by GPIO15 (Linux: 427). value: 1: debug console 0: Z-Wave - NCP-HG100/Cellular has 2x os-image pairs in eMMC. - 0:HLOS, rootfs - 0:HLOS_1, rootfs_1 In OpenWrt, the first image pair is used. - "bootipq" command in U-Boot requires authentication with signed-image by default. To boot unsigned image of OpenWrt, use "mmc read" and "bootm" command instead. - This support is for "Cellular" variant of NCP-HG100 and not tested on "WLAN" (non-cellular) variant. - The board files of ipq-wifi may also be used in "WLAN" variant of NCP-HG100, but unconfirmed and add files as for "Cellular" variant. - "NET" LED is used to indicate WWAN status in stock firmware. - There is no MAC address information in the label on the case, use the address included in UUID in the label as "label-MAC" instead. - The "CLOUD" LEDs are partially used for indication of system status in stock firmware, use they as status LEDs in OpenWrt instead of RGB LED connected to the MCU. MAC addresses: LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex)) WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex)) 2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex)) 5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex)) partition layout in eMMC (by fdisk, GPT): Disk /dev/mmcblk0: 7733248 sectors, 3776M Logical sector size: 512 Disk identifier (GUID): **** Partition table holds up to 20 entries First usable sector is 34, last usable sector is 7634910 Number Start (sector) End (sector) Size Name 1 34 1057 512K 0:SBL1 2 1058 2081 512K 0:BOOTCONFIG 3 2082 3105 512K 0:QSEE 4 3106 4129 512K 0:QSEE_1 5 4130 4641 256K 0:CDT 6 4642 5153 256K 0:CDT_1 7 5154 6177 512K 0:BOOTCONFIG1 8 6178 6689 256K 0:APPSBLENV 9 6690 8737 1024K 0:APPSBL 10 8738 10785 1024K 0:APPSBL_1 11 10786 11297 256K 0:ART 12 11298 11809 256K 0:HSEE 13 11810 28193 8192K 0:HLOS 14 28194 44577 8192K 0:HLOS_1 15 44578 306721 128M rootfs 16 306722 568865 128M rootfs_1 17 568866 3958065 1654M rootfs_data [initial work] Signed-off-by: Iwao Yuki <dev.clef@gmail.com> Co-developed-by: Iwao Yuki <dev.clef@gmail.com> [adjustments, cleanups, commit message, sending patch] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (dropped clk_unused_ignore, dropped 901-* patches, renamed key nodes, changed LEDs chan/labels to match func-en, made :net -> (w)wan leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-04 12:27:11 +00:00
sony_ncp-hg100-cellular \
ipq40xx: Add ZTE MF289F It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
teltonika_rutx \
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
xiaomi_ax3600 \
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-10 23:50:37 +00:00
xiaomi_ax9000 \
ipq40xx: Add support ZTE MF18A Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2022-12-28 18:01:40 +00:00
zte_mf18a \
ipq807x: Add ZyXEL NBG7815 ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-03 18:23:41 +00:00
zte_mf289f \
zyxel_nbg7815
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
define Package/ipq-wifi-default
SUBMENU:=ath10k Board-Specific Overrides
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
SECTION:=firmware
CATEGORY:=Firmware
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_ipq807x)
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
TITLE:=Custom Board
endef
define ipq-wifi-install-one-to
$(INSTALL_DIR) $(2)/lib/firmware/ath10k/$(3)/
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
endef
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
define ipq-wifi-install-ath11-one-to
$(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
endef
define ipq-wifi-install-one
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
$(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
ipq40xx: Add support ZTE MF18A Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2022-12-28 18:01:40 +00:00
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
$(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-10 23:50:37 +00:00
$(if $(filter $(suffix $(1)),.QCN9074 .qcn9074),\
$(call ipq-wifi-install-ath11-one-to,$(1),$(2),QCN9074/hw1.0),\
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-10 23:50:37 +00:00
)))))))
endef
# Blank line required at end of above define due to foreach context
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
define generate-ipq-wifi-package
define Package/ipq-wifi-$(1)
$(call Package/ipq-wifi-default)
TITLE:=board-2.bin Overrides for $(2)
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
CONFLICTS:=$(PREV_BOARD)
endef
define Package/ipq-wifi-$(1)/description
The $(2) requires board-specific, reference ("cal") data
that is not yet present in the upstream wireless firmware distribution.
This package supplies board-2.bin file(s) that, in the interim,
overwrite those supplied by the ath10k-firmware-* packages.
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
This is package is only necessary for the $(2).
Do not install it for any other device!
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
endef
define Package/ipq-wifi-$(1)/install-overlay
$$$$(foreach IPQ_WIFI_BOARD_FILE,$$$$(wildcard $(PKG_BUILD_DIR)/board-$(1).*),\
$$$$(call ipq-wifi-install-one,$$$$(IPQ_WIFI_BOARD_FILE),$$(1)))
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
endef
PREV_BOARD+=ipq-wifi-$(1)
endef
# Add board name to ALLWIFIBOARDS
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
$(eval $(call generate-ipq-wifi-package,8dev_habanero,8devices Habanero))
$(eval $(call generate-ipq-wifi-package,8dev_jalapeno,8devices Jalapeno))
$(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
ipq807x: add support for Buffalo WXR-5950AX12 Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ8074A. Specification: - SoC : Qualcomm IPQ8074A - RAM : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK) - Flash : RAW NAND 256 MiB (Winbond W29N02GZBIBA) - WLAN : 2.4/5 GHz (IPQ8074A) - Ethernet : 5 ports - WAN : 100/1000/2500/10000 Mbps x1 (AQR113C) - LAN : 100/1000/2500/10000 Mbps x1 (AQR113C), 10/100/1000 Mbps x3 (QCA8075) - LED/Keys : 8x/5x - UART : pin header on PCB (J7) - assignment: 3.3V, GND, TX, RX from disc marking - settings : 115200n8 - Power : 12 VDC, 4 A Flash instruction using initramfs image: 1. Prepare TFTP server with IP address 192.168.11.10 2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and place it to TFTP directory 3. Hold AOSS (WPS) button and power on WXR-5950AX12 4. WXR-5950AX12 downloads initramfs image from TFTP server and boots with it automatically 5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade 6. Wait ~120 seconds to complete flashing Partition layout: 0x000000000000-0x000000100000 : "0:sbl1" 0x000000100000-0x000000200000 : "0:mibib" 0x000000200000-0x000000280000 : "0:bootconfig" 0x000000280000-0x000000300000 : "0:bootconfig1" 0x000000300000-0x000000600000 : "0:qsee" 0x000000600000-0x000000900000 : "0:qsee_1" 0x000000900000-0x000000980000 : "0:devcfg" 0x000000980000-0x000000a00000 : "0:devcfg_1" 0x000000a00000-0x000000a80000 : "0:apdp" 0x000000a80000-0x000000b00000 : "0:apdp_1" 0x000000b00000-0x000000b80000 : "0:rpm" 0x000000b80000-0x000000c00000 : "0:rpm_1" 0x000000c00000-0x000000c80000 : "0:cdt" 0x000000c80000-0x000000d00000 : "0:cdt_1" 0x000000d00000-0x000000d80000 : "0:appsblenv" 0x000000d80000-0x000000e80000 : "0:appsbl" 0x000000e80000-0x000000f80000 : "0:appsbl_1" 0x000000f80000-0x000001000000 : "0:art" 0x000001000000-0x000001080000 : "0:art_1" 0x000001080000-0x000001100000 : "0:orgdata" 0x000001100000-0x000001180000 : "0:orgdata_1" 0x000001180000-0x000005180000 : "rootfs" 0x000005180000-0x000009180000 : "rootfs_recover" 0x000009180000-0x000010000000 : "user_property" Notes: - WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for normal operation and the 2nd one is for recoverying or firmware upgrading on stock. - Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*" partition when booting. This is just a comparation of hash strings. Behaviors: - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover ---> boot from rootfs - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover ---> boot from rootfs_recover Note: this behavior is used for firmware upgrading on stock - "fw_hash" volume in rootfs is missing ---> boot from rootfs_recover - "fw_hash" volume in rootfs_recover is missing ---> boot from rootfs - "fw_hash" volumes in both root* partition are missing ---> boot from rootfs_recover Reverting to stock firmware: 1. Decrypt official image by buffalo-enc and remove header example of decryption: $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \ -d -k olaffuB -O 0xc8 example of removing header (v3.05): - before $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec 00000000 57 58 52 2d 35 39 35 30 41 58 31 32 5f 33 2e 30 |WXR-5950AX12_3.0| 00000010 35 5f 31 2e 30 31 5f 4a 50 5f 6a 70 5f 71 63 61 |5_1.01_JP_jp_qca| 00000020 0a 66 69 6c 65 6c 65 6e 3d 34 35 33 35 30 39 31 |.filelen=4535091| 00000030 32 0a 55 42 49 23 01 00 00 00 00 00 00 00 00 00 |2.UBI#..........| 00000040 - after $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi 00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............| 00000010 00 00 08 00 00 00 10 00 78 cf c4 91 00 00 00 00 |........x.......| 00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000030 00 00 00 00 00 00 00 00 00 00 00 00 3d 2a 64 fd |............=*d.| 00000040 2. Boot WXR-5950AX12 with OpenWrt initramfs image 3. Upload modified stock image to WXR-5950AX12 4. Find partitions "rootfs" and "rootfs_recover" example: root@OpenWrt:/# cat /proc/mtd dev: size erasesize name ... mtd22: 04000000 00020000 "rootfs" mtd23: 04000000 00020000 "rootfs_recover" ... in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23 5. Format "rootfs"/"rootfs_recover" partition with the uploaded image example: ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi 6. Remove "rootfs"/"rootfs_data" volume from user_property partition example: . /lib/upgrade/nand.sh UBI=$(nand_attach_ubi user_property) ubirmvol /dev/$UBI -N rootfs ubirmvol /dev/$UBI -N rootfs_data 7. Reboot MAC addresses: LAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) WAN : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text)) 2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text)) 5 GHz : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text)) Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-01-23 04:01:13 +00:00
$(eval $(call generate-ipq-wifi-package,buffalo_wxr-5950ax12,Buffalo WXR-5950AX12))
ipq40xx: add support for devolo Magic 2 WiFi next SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
2020-10-02 12:32:55 +00:00
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
ipq807x: add Dynalink DL-WRX36 Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-08-05 09:38:37 +00:00
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
ipq806x: add Edgecore ECW5410 support This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-09-07 10:43:37 +00:00
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
ipq807x: add Edimax CAX1800 Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:17:51 +00:00
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
$(eval $(call generate-ipq-wifi-package,extreme-networks_ws-ap3915i,Edgecore OAP100))
$(eval $(call generate-ipq-wifi-package,glinet_gl-a1300,GL.iNet GL-A1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
ipq40xx: Add support for Linksys EA8300 (Dallas) The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-04-10 15:34:28 +00:00
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
ipq40xx: add support for Linksys WHW03 V2 SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2022-12-23 17:30:36 +00:00
$(eval $(call generate-ipq-wifi-package,linksys_whw03v2,Linksys WHW03 V2))
ipq806x: add support for Nokia Airscale AC400i Hardware -------- SoC: Qualcomm IPQ8065 RAM: 512 MB DDR3 Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB) 4 MB SPI-NOR (Macronix MX25U3235F) WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz Qualcomm Atheros QCA9984 - 5Ghz ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt) eth1 - (1000Mbps in both) Auto-negotiation broken on both. USB: USB 2.0 LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red) BTN: Reset Other: SD card slot (non-functional) Serial: 115200bps, near the Ethernet transformers, labeled 9X. Connections from the arrow to the 9X text: [NC] - [TXD] - [GND] - [RXD] - [NC] Installation ------------ 0. Connect to the device Plug your computer into LAN2 (1000Mbps connection required). If you use the LAN1/POE port, set your computer to force a 100Mbps link. Connect to the device via TTL (Serial) 115200n8. Locate the header (or solder pads) labeled 9X, near the Ethernet jacks/transformers. There should be an arrow on the other side of the header marking. The connections should go like this: (from the arrow to the 9X text): NC - TXD - GND - RXD - NC 1. Prepare for installation While the AP is powering up, interrupt the startup process. MAKE SURE TO CHECK YOUR CURRENT PARTITION! If you see: "Current Partition is : partB" or "Need to switch partition from partA to partB", you have to force the device into partA mode, before continuing. This can be done by changing the PKRstCnt to 5 and resetting the device. setenv PKRstCnt 5 saveenv reset After you interrupt the startup process again, you should see: Need to switch partition from partB to partA You can now continue to the next step. If you see: "Current Partition is : partA", you can continue to the next step. 2. Prevent partition switching. To prevent the device from switching partitions, we are going to modify the startup command. set bootcmd "setenv PKRstCnt 0; saveenv; bootipq" setenv 3. First boot Now, we have to boot the OpenWrt intifs. The easiest way to do this is by using Tiny PXE. You can also use the normal U-Boot tftp method. Run "bootp" this will get an IP from the DHCP server and possibly the firmware image. If it doesn't download the firmware image, run "tftpboot". Now run "bootm" to run the image. You might see: "ERROR: new format image overwritten - must RESET the board to recover" this means that the image you are trying to load is too big. Use a smaller image for the initial boot. 4. Install OpenWrt from initfs Once you are booted into OpenWrt, transfer the OpenWrt upgrade image and use sysupgrade to install OpenWrt to the device. Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
2023-02-04 16:00:57 +00:00
$(eval $(call generate-ipq-wifi-package,nokia_ac400i,Nokia AC400i))
ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0) P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> Signed-off-by: Richard Yu <yurichard3839@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> [Added comment about MIBIB+128 MiB variant. Added commit message section about pcie slot. Renamed gpio-leds' subnodes and added color, function+enum properties.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-12 03:16:21 +00:00
$(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC))
$(eval $(call generate-ipq-wifi-package,pakedge_wr-1,Pakedge WR-1))
ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:20:19 +00:00
$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
ipq807x: add Redmi AX6 Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
2022-01-01 22:12:51 +00:00
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
ipq40xx: add support for Sony NCP-HG100/Cellular Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac (WiFi-5) wireless function, based on IPQ4019. Specification: - SoC : Qualcomm IPQ4019 - RAM : DDR3 512 MiB (H5TC4G63EFR) - Flash : eMMC 4 GiB (THGBMNG5D1LBAIT) - WLAN : 2.4/5 GHz 2T2R (IPQ4019) - Ethernet : 10/100/1000 Mbps x2 - Transceiver : Qualcomm QCA8072 - WWAN : Telit LN940A9 - Z-Wave : Silicon Labs ZM5101 - Bluetooth : Qualcomm CSR8811 - Audio DAC : Realtek ALC5629 - Audio Amp. : Realtek ALC1304 - Voice Input Processor : Conexant CX20924 - Micro Controller Unit : Nuvoton MINI54FDE - RGB LED, Fan, Temp. sensors - Touch Sensor : Cypress CY8C4014LQI - RGB LED driver : TI LP55231 (2x) - LEDs/Keys : 11x, 6x - UART : through-hole on PCB - J1: 3.3V, TX, RX, GND from tri-angle marking - 115200n8 - Power : 12 VDC, 2.5 A Flash instruction using initramfs image: 1. Prepare TFTP server with the IP address 192.168.132.100 and place the initramfs image to TFTP directory with the name "C0A88401.img" 2. Boot NCP-HG100/Cellular and interrupt after the message "Hit any key to stop autoboot: 2" 3. Perform the following commands and set bootcmd to allow booting from eMMC setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000" saveenv 4. Perform the following command to load/boot the OpenWrt initramfs image tftpboot && bootm 5. On the initramfs image, perform sysupgrade with the sysupgrade image (if needed, backup eMMC partitions by dd command and download to other place before performing sysupgrade) 6. Wait for ~120 seconds to complete flashing Known issues: - There are no drivers for audio-related chips/functions in Linux Kernel and OpenWrt, they cannot be used. - There is no driver for MINI54FDE Micro-Controller Unit, customized for this device by the firmware in the MCU. This chip controls the following functions, but they cannot be controlled in OpenWrt. - RGB LED - Fan this fan is controlled automatically by MCU by default, without driver - Thermal Sensors (2x) - Currently, there is no driver or tool for CY8C4014LQI and cannot be controlled. It cannot be exited from "booting mode" and moved to "normal op mode" after booting. And also, the 4x buttons (mic mute, vol down, vol up, alexa trigger) connected to the IC cannot be controlled. - it can be exited from "booting mode" by installing and executing i2cset command: opkg update opkg install i2c-tools i2cset -y 1 0x14 0xf 1 - There is a connection issue on the control by uqmi for the WWAN module. But modemmanager can be used without any issues and the use of it is recommended. - With the F2FS format, too many errors are reported on erasing eMMC partition "rootfs_data" while booting: [ 1.360270] sdhci: Secure Digital Host Controller Interface driver [ 1.363636] sdhci: Copyright(c) Pierre Ossman [ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO ... [ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 1.528325] mmc0: new HS200 MMC card at address 0001 [ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB [ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB [ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB [ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0) [ 1.550323] Alternate GPT is invalid, using primary GPT. [ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 ... [ 8.841400] mount_root: loading kmods from internal overlay [ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 9.240465] block: attempting to load /etc/config/fstab [ 9.246722] block: unable to load configuration (fstab: Entry not found) [ 9.246863] block: no usable configuration [ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet [ 9.438915] urandom_read: 5 callbacks suppressed [ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read) [ 12.243332] mmc_erase: erase error -110, status 0x800 [ 12.246638] mmc0: cache flush error -110 [ 15.134585] mmc_erase: erase error -110, status 0x800 [ 15.135891] mmc_erase: group start error -110, status 0x0 [ 15.139850] mmc_erase: group start error -110, status 0x0 ...(too many the same errors)... [ 17.350811] mmc_erase: group start error -110, status 0x0 [ 17.356197] mmc_erase: group start error -110, status 0x0 [ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00 [ 17.446910] mmc0: tuning execution failed: -5 [ 17.447111] mmc0: cache flush error -110 [ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint [ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b [ 18.198691] block: attempting to load /etc/config/fstab [ 18.198972] block: unable to load configuration (fstab: Entry not found) [ 18.203029] block: no usable configuration [ 18.211371] mount_root: overlay filesystem has not been fully initialized yet [ 18.214487] mount_root: switching to f2fs overlay So, this support uses ext4 format instead which has no errors. Note: - The primary uart is shared for debug console and Z-Wave chip. The function is switched by GPIO15 (Linux: 427). value: 1: debug console 0: Z-Wave - NCP-HG100/Cellular has 2x os-image pairs in eMMC. - 0:HLOS, rootfs - 0:HLOS_1, rootfs_1 In OpenWrt, the first image pair is used. - "bootipq" command in U-Boot requires authentication with signed-image by default. To boot unsigned image of OpenWrt, use "mmc read" and "bootm" command instead. - This support is for "Cellular" variant of NCP-HG100 and not tested on "WLAN" (non-cellular) variant. - The board files of ipq-wifi may also be used in "WLAN" variant of NCP-HG100, but unconfirmed and add files as for "Cellular" variant. - "NET" LED is used to indicate WWAN status in stock firmware. - There is no MAC address information in the label on the case, use the address included in UUID in the label as "label-MAC" instead. - The "CLOUD" LEDs are partially used for indication of system status in stock firmware, use they as status LEDs in OpenWrt instead of RGB LED connected to the MCU. MAC addresses: LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex)) WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex)) 2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex)) 5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex)) partition layout in eMMC (by fdisk, GPT): Disk /dev/mmcblk0: 7733248 sectors, 3776M Logical sector size: 512 Disk identifier (GUID): **** Partition table holds up to 20 entries First usable sector is 34, last usable sector is 7634910 Number Start (sector) End (sector) Size Name 1 34 1057 512K 0:SBL1 2 1058 2081 512K 0:BOOTCONFIG 3 2082 3105 512K 0:QSEE 4 3106 4129 512K 0:QSEE_1 5 4130 4641 256K 0:CDT 6 4642 5153 256K 0:CDT_1 7 5154 6177 512K 0:BOOTCONFIG1 8 6178 6689 256K 0:APPSBLENV 9 6690 8737 1024K 0:APPSBL 10 8738 10785 1024K 0:APPSBL_1 11 10786 11297 256K 0:ART 12 11298 11809 256K 0:HSEE 13 11810 28193 8192K 0:HLOS 14 28194 44577 8192K 0:HLOS_1 15 44578 306721 128M rootfs 16 306722 568865 128M rootfs_1 17 568866 3958065 1654M rootfs_data [initial work] Signed-off-by: Iwao Yuki <dev.clef@gmail.com> Co-developed-by: Iwao Yuki <dev.clef@gmail.com> [adjustments, cleanups, commit message, sending patch] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (dropped clk_unused_ignore, dropped 901-* patches, renamed key nodes, changed LEDs chan/labels to match func-en, made :net -> (w)wan leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-04 12:27:11 +00:00
$(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
ipq40xx: Add support for Teltonika RUTX10 This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org>
2021-07-15 19:48:11 +00:00
$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
ipq807x: add Xiaomi AX3600 Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-05-19 19:04:43 +00:00
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
ipq807x: Add Xiaomi AX9000 Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-01-10 23:50:37 +00:00
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
ipq40xx: Add support ZTE MF18A Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2022-12-28 18:01:40 +00:00
$(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
ipq40xx: Add ZTE MF289F It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-14 12:20:43 +00:00
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
ipq807x: Add ZyXEL NBG7815 ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-03 18:23:41 +00:00
$(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
firmware: add custom IPQ wifi board definitions On the ath10k-devel ML Michael Kazior stated: "board-2 is a key-value store of actual board files. Some devices, notably qca61x4 hw3+ and qca4019 need distinct board files to be uploaded. Otherwise they fail in various ways." [0]. Later on Rajkumar Manoharan explained: "In QCA4019 platform, only radio specific calibration (pre-cal-data) is stored in flash. Board specific contents are read from board-2.bin. For each radio appropriate board data should be loaded. To fetch correct board data from board-2.bin bundle, pre-cal/radio specific caldata should be loaded first to get proper board id. |My understanding until now was that: | | * pre-cal data + board-2.bin info == actual calibration data Correct." [1]. The standard board-2.bin from the ath10k-firmware-qca4019 barely works on the RT-AC58U. Especially 5GHz clients fail to connect at all and if they do, they have very low throughput even right next to the router. Currently, the solution for this problem is to supply a custom board-2.bin for every device. To implement this feature, this method makes use of: Rafał Miłecki's "base-files: add support for overlaying rootfs content". This comes with a few limitations: 1. Since there can only be one board-2.bin at the right location, there can only one board overwrite installed at any time. (All packages CONFLICT with each other. It's also not possible to "builtin" multiple package.) 2. updating ath10k-firmware-qca4019 will also replace the board-2.bin. For this cases the user needs to manually reinstall the wifi-board package once the ath10k-firmware-qca4019 is updated. To create the individual board-2.bin: Use the ath10k-bdencoder utility from the qca-swiss-army-knife repository: <https://github.com/qca/qca-swiss-army-knife> The raw board.bin files have to be extracted from the vendor's source GPL.tar archieves. Signed-off-by: Alexis Green <agreen@cococorp.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-03-15 10:49:14 +00:00
$(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))