ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-22 15:02:32 +00:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
57f2c72505
openwrt/target/linux/mvebu/image/cortexa9.mk

450 lines
14 KiB
Makefile
Raw Normal View History

target: use SPDX license identifiers on Makefiles Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 13:52:34 +00:00
# SPDX-License-Identifier: GPL-2.0-only
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
#
# Copyright (C) 2012-2016 OpenWrt.org
# Copyright (C) 2016 LEDE-project.org
mvebu: cortexa9: set DTS dir for 6.6 With 6.6, all DTSes were moved to their vendor subdirectories. ARM64 DTSes already used this scheme, but 32 bit Cortex A9 did not, prior to 6.6. Introduce a kernel version check to keep backward compatibility with 6.1. Suggested-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2024-03-19 21:55:11 +00:00
DTS_DIR := $(DTS_DIR)/marvell
mvebu: add support for Fortinet FortiGate 50E Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-50E and interrupt to show bootmenu 2. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 3. Prepare TFTP server with the parameters obtained above 4. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 6. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 7. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 7. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 8. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of WAN1/2 are connected to GPIO expander. There is no way to indicate link speed of networking device on Linux Kernel/OpenWrt, so those LEDs cannot be handled like stock firmware. On OpenWrt, use netdev(link) trigger instead. - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex)) WAN 1 : 70:4C:A5:xx:xx:7D WAN 2 : 70:4C:A5:xx:xx:7E LAN 1 : 70:4C:A5:xx:xx:7F LAN 2 : 70:4C:A5:xx:xx:80 LAN 3 : 70:4C:A5:xx:xx:81 LAN 4 : 70:4C:A5:xx:xx:82 LAN 5 : 70:4C:A5:xx:xx:83 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 12:54:14 +00:00
define Build/fortigate-header
( \
dd if=/dev/zero bs=384 count=1 2>/dev/null; \
datalen=$$(wc -c $@ | cut -d' ' -f1); \
datalen=$$(printf "%08x" $$datalen); \
datalen="$${datalen:6:2}$${datalen:4:2}$${datalen:2:2}$${datalen:0:2}"; \
printf $$(echo "00020000$${datalen}ffff0000ffff0000" | sed 's/../\\x&/g'); \
dd if=/dev/zero bs=112 count=1 2>/dev/null; \
cat $@; \
) > $@.new
mv $@.new $@
endef
mvebu: add support for IIJ SA-W2 Internet Initiative Japan Inc. (IIJ) SA-W2 is a network appliance with 11ac (Wi-Fi 5) wlan, based on 88F6810. Specification: - SoC : Marvell Armada 380 88F6810 - RAM : DDR3 256 MiB (Micron MT41K64M16TW-107:J x2) - Flash : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ) - WLAN : 2.4/5 GHz, Mini PCI-E - 2.4 GHz : Silex SX-PCEGN (Atheros AR9287 (2T2R)) - 5 GHz : Silex SX-PCEAC (Qualcomm Atheros QCA9880 (3T3R)) - Ethernet : 10/100/1000 Mbps x5 - Switch : Marvell 88E6172 - LEDs/Keys : 12x/1x - UART : "CONSOLE" port (RJ-45, RS-232C) - settings : 115200n8 - assignment: 1:NC, 2:NC, 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC, 8:NC - note : compatible with Cisco console cable - Power : DC Input or PoE - DC Input : 12 VDC, 3 A - PoE : 802.3af - module : Silvertel Ag9712-2BR - note : USB ports shouldn't be used when powered by PoE - Bootloader : PMON2000 based - Stock : NetBSD based Flash instruction using sysupgrade image: 1. Prepare TFTP server with IP address 192.168.0.10 and put sysupgrade image to TFTP directory 2. Connect PC to "GE0/PoE" port on SA-W2 3. Power on SA-W2, interrupt count-down by Esc and enter to bootloader CLI 4. Set IP address of the device address 192.168.0.1 5. Download sysupgrade image and flash to storage tftpload 192.168.0.10 <image name> firmwrite example: #tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin Loading openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin loaded 8127268 byte(s) #firmwrite Erasing FLASH block 32 Done 0x00200000. Erasing FLASH block 33 Done 0x00210000. ... Erasing FLASH block 155 Done 0x009b0000. Erasing FLASH block 156 Done 0x009c0000. Programming FLASH. Done. Verifying FLASH. No Errors found. 6. Check the flashed firmware firmcheck example: #firmcheck [Normal firmware] ident: 'SEIL2015' copyright: 'ARM OpenWrt Linux-5.15.93' version format: 1 version major: 9 version minor: 99 version release: 'r22060+36-5163bb5e54' body size: 3578524 checksum: 0x8a083cb8 [Rescue firmware] ident: 'SEIL2015' copyright: 'Copyright (c) 2017 Internet Initiative Japan Inc. All rights reserved.' version format: 1 version major: 3 version minor: 70 version release: 'Release' body size: 10152458 checksum: 0x8f9518c2 7. Boot with the flashed firmware boot Note: - The bootloader on this device is not U-Boot and it's environment space ("bootloader-env") has no compatibility with U-Boot tools. - eth1 is connected to port6 of 88E6172 switch, but multi-cpu port can't be handled on Linux Kernel and not defined. - Powering by PoE hasn't been tested yet. - This device has 2x OS images on flash and they can be switched by setting "BOOTDEV" variable on bootloader CLI. That variable supports the following values: - "flash" : primary image on flash ("firmware") - "rescue": secondary image on flash ("rescue") - "usb" : usb storage (broken?) - "lan0/1": network command to set: set BOOTDEV=<dev> example: set BOOTDEV=rescue This commit also supports booting from secondary partition. - To execute initramfs image on bootloader CLI, use "go" command. ("go" command is not listed on the output of "help", but available) example (download and execute): address 192.168.0.1 tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-initramfs-kernel.bin go MAC addresses: LAN : 00:E0:4D:xx:xx:19 (none) WAN : 00:E0:4D:xx:xx:18 (board_info, 0x6 (hex)) 2.4 GHz: 84:25:3F:xx:xx:xx (Mini PCI-E card) 5 GHz : 84:25:3F:xx:xx:xx (Mini PCI-E card) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-11-13 08:22:26 +00:00
define Build/seil-header
( \
data_size_crc="$$(gzip -c $@ | tail -c8 | \
od -An -tx8 --endian little | tr -d ' \n')"; \
printf "SEIL2015"; \
printf "$(call toupper,$(LINUX_KARCH)) $(VERSION_DIST) Linux-$(LINUX_VERSION)" | \
dd bs=80 count=1 conv=sync 2>/dev/null; \
printf "$$(echo $${data_size_crc:8:8} | sed 's/../\\x&/g')"; \
printf "\x00\x00\x00\x01\x00\x00\x00\x09\x00\x00\x00\x63"; \
printf "$(REVISION)" | dd bs=32 count=1 conv=sync 2>/dev/null; \
printf "\x00\x00\x00\x00"; \
printf "$$(echo $${data_size_crc:0:8} | sed 's/../\\x&/g')"; \
cat $@; \
) > $@.new
mv $@.new $@
endef
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
define Device/dsa-migration
DEVICE_COMPAT_VERSION := 1.1
Revert "treewide: add sysupgrade comment for early DSA-adopters" This reverts commit e81e625ca375d6dc3c885ec870ec15757ac76d72. This was meant just for early DSA-adopters. Those should have updated by now, remove it so future updaters get the intended experience. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 19:30:44 +00:00
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
endef
mvebu: mamba resize kernel to 4MB mamba has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. mamba uboot however as set from factory will load up to 4MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0xa00000, size 0x400000 4194304 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "pri_kern_size"; pri_kern_size=0x400000 Resize the root partitions from 37MB to 36MB to let kernel expand into it another 1MB. And set kernel target size to 4MB. Lastly add a compatibility version message: kernel-size-migration. And set it on mamba to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-02-06 03:38:03 +00:00
define Device/kernel-size-migration
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (up to 19.07) due to kernel size restrictions. \
Upgrade via sysupgrade mechanism is not possible, so new installation via factory style image is required.
endef
mvebu: add support for Buffalo LinkStation LS220DE The Buffalo LinkStation LS220DE is a dual bay NAS, based on Marvell Armada 370 Hardware: SoC: Marvell Armada 88F6707 CPU: Cortex-A9 800 MHz, 1 core Flash 1: SPI-NOR 1 MiB (U-Boot) Flash 2: NAND 512 MiB (OS) RAM: DDR3 256 MiB Ethernet: 1x 1GbE USB: 1x 2.0 SATA: 2x 3Gb/s LEDs/Input: 5x / 2x (1x button, 1x slide-switch) Fan: 1x casing Flash instructions, from hard drive: 1. Get access to the "boot" partition at the hard drive where the stock firmware is installed. It can be done with acp-commander or by plugging the hard drive to a computer. 2. Backup the stock uImage: mv /boot/uImage.buffalo /boot/uImage.buffalo.bak 3. Move and rename the Openwrt initramfs image to the boot partition: mv openwrt-initramfs-kernel.bin /boot/uImage.buffalo 4. Power on the Linkstation with the hardrive inside. Now Openwrt will boot, but still not installed. 5. Connect via ssh to OpenWrt: ssh root@192.168.1.1 6. Rename boot files inside boot partition mount -t ext3 /dev/sda1 /mnt mv /mnt/uImage.buffalo /mnt/uImage.buffalo.openwrt.bak mv /mnt/initrd.buffalo /mnt/initrd.buffalo.bak 7. Format ubi partitions at the NAND flash ("kernel_ubi" and "ubi"): ubiformat /dev/mtd0 -y ubidetach -p /dev/mtd1 ubiformat /dev/mtd1 -y 8. Flash the sysupgrade image: sysupgrade -n openwrt-squashfs-sysupgrade.bin 9. Wait until it finish, the device will reboot with OpenWrt installed on the NAND flash. Restore the stock firmware: 1. Take the hard drive used for the installation and restore boot backup files to their original names: mount -t ext3 /dev/sda1 /mnt mv /mnt/uImage.buffalo.bak /mnt/uImage.buffalo mv /mnt/initrd.buffalo.bak /mnt/initrd.buffalo 2. Boot from the hard drive and perform a stock firmware update using the Buffalo utility. The NAND will be restored to the original state. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-02-20 23:43:55 +00:00
define Device/buffalo_ls220de
$(Device/NAND-128K)
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := LinkStation LS220DE
KERNEL_UBIFS_OPTS = -m $$(PAGESIZE) -e 124KiB -c 172 -x none
KERNEL := kernel-bin | append-dtb | uImage none | buffalo-kernel-ubifs
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
DEVICE_DTS := armada-370-buffalo-ls220de
DEVICE_PACKAGES := \
kmod-hwmon-gpiofan kmod-hwmon-drivetemp kmod-linkstation-poweroff \
kmod-md-mod kmod-md-raid0 kmod-md-raid1 kmod-md-raid10 kmod-fs-xfs \
mdadm mkf2fs e2fsprogs partx-utils
endef
TARGET_DEVICES += buffalo_ls220de
mvebu: add support for Buffalo LinkStation LS421DE Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370 Hardware: SoC: Marvell Armada 88F6707-A1 CPU: Cortex-A9 1200 MHz, 1 core Flash: SPI-NOR 1 MiB, NAND 512 MiB RAM: DDR3 512 MiB Ethernet: 1x 10/100/1000 Mbps USB: 1x 2.0, 1x 3.0 SATA: 2x 3.0 Gbps LEDs/Input : 5x / 2x (1x button, 1x slide-switch) RTC: Ricoh RS5C372A, I2C, no battery Flash instruction (UART+TFTP): 1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13) 2. Remove any hard drive from inside the bays. 3. Boot the Openwrt initramfs image using the U-Boot serial console: tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin bootm 0x1200000 4. Flash the sysupgrade image using the Openwrt console: sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin 5. Wait until it finish, the device will reboot with Openwrt installed on the NAND flash. Note: - Device shuting down doesn't work, even if the power slide switch is used. We must first, via MDIO, set the unused LED2 at the ethernet phy0 to off state. Reboot works ok. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-07 12:35:26 +00:00
define Device/buffalo_ls421de
$(Device/NAND-128K)
DEVICE_VENDOR := Buffalo
DEVICE_MODEL := LinkStation LS421DE
SUBPAGESIZE :=
KERNEL_SIZE := 33554432
FILESYSTEMS := squashfs ubifs
KERNEL := kernel-bin | append-dtb | uImage none | buffalo-kernel-jffs2
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
DEVICE_DTS := armada-370-buffalo-ls421de
DEVICE_PACKAGES := \
mvebu: LS421DE: use automatic fan control with thermal zones The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal hard drives. Currently there is no control over this fan, running always at fixed medium speed. With the recent jump to the kernel 5.4, now we can monitor the hard drive temperature and control the fan with thermal zones. Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the dts file to allow automatic fan control by the kernel. Tested succesfully using a single Crucial BX500 SSD drive. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-06-28 21:52:10 +00:00
kmod-rtc-rs5c372a kmod-hwmon-gpiofan kmod-hwmon-drivetemp kmod-usb3 \
mvebu: LS421DE: add linkstation poweroff driver Compile the Linkstation poweroff module for the Buffalo LS421DE. Without this driver the device remains forever halted if a power off command is executed. The driver will also allow to use the WoL feature, which wasn't availabe in the stock firmware. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-08-28 09:20:46 +00:00
kmod-linkstation-poweroff kmod-md-raid0 kmod-md-raid1 kmod-md-mod \
kmod-fs-xfs mkf2fs e2fsprogs partx-utils
mvebu: add support for Buffalo LinkStation LS421DE Buffalo LinkStation LS421DE is a dual bay NAS, based on Marvell Armada 370 Hardware: SoC: Marvell Armada 88F6707-A1 CPU: Cortex-A9 1200 MHz, 1 core Flash: SPI-NOR 1 MiB, NAND 512 MiB RAM: DDR3 512 MiB Ethernet: 1x 10/100/1000 Mbps USB: 1x 2.0, 1x 3.0 SATA: 2x 3.0 Gbps LEDs/Input : 5x / 2x (1x button, 1x slide-switch) RTC: Ricoh RS5C372A, I2C, no battery Flash instruction (UART+TFTP): 1. Downgrade the OEM firmware to 1.34 version (BUFFALO_BOOTVER=0.13) 2. Remove any hard drive from inside the bays. 3. Boot the Openwrt initramfs image using the U-Boot serial console: tftpboot 0x1200000 buffalo_ls421de-initramfs-kernel.bin bootm 0x1200000 4. Flash the sysupgrade image using the Openwrt console: sysupgrade -n buffalo_ls421de-squashfs-sysupgrade.bin 5. Wait until it finish, the device will reboot with Openwrt installed on the NAND flash. Note: - Device shuting down doesn't work, even if the power slide switch is used. We must first, via MDIO, set the unused LED2 at the ethernet phy0 to off state. Reboot works ok. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-04-07 12:35:26 +00:00
endef
TARGET_DEVICES += buffalo_ls421de
mvebu: cortexa9: Add support for Ctera C200-V2 2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC) - Ram: 1GB (2x Nanya NT5CC512M8DN-D1) - NAND Flash: 256MB (ESMT F59L2G81A-25T) - Lan: 1x GBE (Marvell 88E1318-NNB2) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 3.0 port (Renesas uPD720202) - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver - USB1/2 usbport ledtrigger won't work (through DT) - Renesas uPD720202 requires firmware file. It's possible to find non-free binary. Please look for 'UPDATE.mem' file and put in into '/lib/firmware/renesas_usb_fw.mem' file. Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ## ctera_c200-v2_back_to_factory start ## . /lib/functions.sh part=$(find_mtd_part "active_bank") active_bank=$(strings "$part" | grep bank) if [ "$active_bank" = "bank1" ]; then echo "bank2" > /tmp/change_bank else echo "bank1" > /tmp/change_bank fi mtd write /tmp/change_bank active_bank reboot ## ctera_c200-v2_back_to_factory end ## Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (put back-to-stock script into commit message, removed dup. SUBPAGESIZE var, added 01_leds for non-working dt-usb-port trigger) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-11 22:23:22 +00:00
define Device/ctera_c200-v2
PAGESIZE := 2048
SUBPAGESIZE := 512
BLOCKSIZE := 128k
DEVICE_VENDOR := Ctera
DEVICE_MODEL := C200
DEVICE_VARIANT := V2
SOC := armada-370
KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
KERNEL_IN_UBI :=
KERNEL_SUFFIX := -factory.firm
DEVICE_PACKAGES := \
kmod-gpio-button-hotplug kmod-hwmon-drivetemp kmod-hwmon-nct7802 \
kmod-rtc-s35390a kmod-usb3 kmod-usb-ledtrig-usbport
IMAGES := sysupgrade.bin
endef
TARGET_DEVICES += ctera_c200-v2
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
define Device/cznic_turris-omnia
DEVICE_VENDOR := CZ.NIC
DEVICE_MODEL := Turris Omnia
KERNEL_INSTALL := 1
mvebu: omnia: make initramfs image usable out of the box Currently it's not possible to boot the device with just initramfs image without additional effort as the initramfs image doesn't contain device tree. Fix it by producing FIT based image which could be booted with following commands: setenv bootargs earlyprintk console=ttyS0,115200 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin bootm ${kernel_addr_r} Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-01-30 12:32:43 +00:00
SOC := armada-385
Revert "mvebu: fix initramfs/kernel image for CZNIC Turris Omnia" This reverts commit e401a2a42e6d7c892e1cf7d765fa5ec9b2db3fb3 as at least two users had reported breakage on their devices. References: https://lists.infradead.org/pipermail/openwrt-devel/2020-December/032837.html References: https://github.com/openwrt/openwrt/commit/e401a2a42e6d7c892e1cf7d765fa5ec9b2db3fb3#commitcomment-45189788 Cc: Karel Kočí <karel.koci@nic.cz> Reported-by: Magnus Kroken <mkroken@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-12-22 12:17:32 +00:00
KERNEL := kernel-bin
mvebu: omnia: make initramfs image usable out of the box Currently it's not possible to boot the device with just initramfs image without additional effort as the initramfs image doesn't contain device tree. Fix it by producing FIT based image which could be booted with following commands: setenv bootargs earlyprintk console=ttyS0,115200 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin bootm ${kernel_addr_r} Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-01-30 12:32:43 +00:00
KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
DEVICE_PACKAGES := \
mkf2fs e2fsprogs kmod-fs-vfat kmod-nls-cp437 kmod-nls-iso8859-1 \
treewide: replace wpad-basic-wolfssl default The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-12-28 04:44:11 +00:00
wpad-basic-mbedtls kmod-ath9k kmod-ath10k-ct ath10k-firmware-qca988x-ct \
mvebu: Add kmod-turris-omnia-mcu Add support for the MCU driver on CZ.NIC's Turris Omnia. This adds the ability to do a true board poweroff, and to configure various features (for example the user may configure that after poweroff, the router should automatically wake up at a specific time). Signed-off-by: Marek Mojík <marek.mojik@nic.cz> Signed-off-by: Marek Behún <kabel@kernel.org> Link: https://github.com/openwrt/openwrt/pull/13799 Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-10-20 09:29:37 +00:00
kmod-mt7915-firmware partx-utils kmod-i2c-mux-pca954x kmod-leds-turris-omnia \
utils: Add the omnia-mcutool utility Add a new utility, omnia-mcutool, which main purpose is to upgrade the firmware on the microcontroller on the Turris Omnia router. Depends on omnia-mcu-firmware, and the upgrade process is pretty simple: omnia-mcutool --upgrade Besides firmware upgrade, the utility can be used to show and configure various firmware settings. Signed-off-by: Marek Mojík <marek.mojik@nic.cz> Signed-off-by: Marek Behún <kabel@kernel.org> Link: https://github.com/openwrt/openwrt/pull/13799 Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-10-26 11:46:11 +00:00
kmod-turris-omnia-mcu kmod-gpio-button-hotplug omnia-mcu-firmware omnia-mcutool
mvebu: stop building omnia-medkit Since August 2022, users of very old Turris Omnias have been encouraged to update U-Boot before OpenWrt installation [1]. The omnia-medkit (only useful for installation with U-Boot 2015.10-rc2) is not needed anymore. [1] https://openwrt.org/toh/turris/turris_omnia#installation Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
2022-02-26 08:37:26 +00:00
IMAGES := sysupgrade.img.gz
IMAGE/sysupgrade.img.gz := boot-scr | boot-img | sdcard-img | gzip | append-metadata
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
SUPPORTED_DEVICES += armada-385-turris-omnia
mvebu: Add turris-omnia.bootscript In contrast to the U-Boot version shipped with older versions of Turris Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019 (CZ11NIC23) relies on the existence of /boot.scr. Consequently, add a suitable boot script to the sysupgrade image. Flash instructions for Turris Omnia 2019: - Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting .img file to the root of a USB flash drive (FAT32 or ext2/3/4). - Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1 on LAN port 4, or via 7-LED reset and the serial console. - Insert the USB drive and mount it: mkdir /mnt; mount /dev/sda1 /mnt - Flash the OpenWrt image to eMMC: dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync - Reboot. Flash instructions using a temporary "medkit" installation were written for the older versions of Turris Omnia, and will *not* work on the Turris Omnia 2019. Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
2019-12-23 07:34:49 +00:00
BOOT_SCRIPT := turris-omnia
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
endef
TARGET_DEVICES += cznic_turris-omnia
mvebu: add common image definition for FortiGate devices Add a common definition of Fortinet FortiGate devices to image/cortexa9.mk for a preparation of adding support for other FortiGate 3xE/5xE devices. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-12-04 12:02:13 +00:00
define Device/fortinet
mvebu: add support for Fortinet FortiGate 30E Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 5x 10/100/1000 Mbps - Switch : Marvell 88E6176 - LEDs/Keys : 16x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Modex 5557-02R Flash instruction using initramfs image: 1. Power on FG-30E and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex)) WAN : 70:4C:A5:xx:xx:CF LAN 1 : 70:4C:A5:xx:xx:D0 LAN 2 : 70:4C:A5:xx:xx:D1 LAN 3 : 70:4C:A5:xx:xx:D2 LAN 4 : 70:4C:A5:xx:xx:D3 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-21 06:23:56 +00:00
DEVICE_VENDOR := Fortinet
SOC := armada-385
KERNEL := kernel-bin | append-dtb
KERNEL_SIZE := 6144k
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := kmod-hwmon-nct7802
endef
mvebu: add common image definition for FortiGate devices Add a common definition of Fortinet FortiGate devices to image/cortexa9.mk for a preparation of adding support for other FortiGate 3xE/5xE devices. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-12-04 12:02:13 +00:00
define Device/fortinet_fg-30e
$(Device/fortinet)
DEVICE_MODEL := FortiGate 30E
DEVICE_DTS := armada-385-fortinet-fg-30e
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FGT30E
endef
mvebu: add support for Fortinet FortiGate 30E Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 5x 10/100/1000 Mbps - Switch : Marvell 88E6176 - LEDs/Keys : 16x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Modex 5557-02R Flash instruction using initramfs image: 1. Power on FG-30E and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex)) WAN : 70:4C:A5:xx:xx:CF LAN 1 : 70:4C:A5:xx:xx:D0 LAN 2 : 70:4C:A5:xx:xx:D1 LAN 3 : 70:4C:A5:xx:xx:D2 LAN 4 : 70:4C:A5:xx:xx:D3 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-21 06:23:56 +00:00
TARGET_DEVICES += fortinet_fg-30e
mvebu: add support for Fortinet FortiGate 50E Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-50E and interrupt to show bootmenu 2. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 3. Prepare TFTP server with the parameters obtained above 4. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 6. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 7. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 7. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 8. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of WAN1/2 are connected to GPIO expander. There is no way to indicate link speed of networking device on Linux Kernel/OpenWrt, so those LEDs cannot be handled like stock firmware. On OpenWrt, use netdev(link) trigger instead. - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex)) WAN 1 : 70:4C:A5:xx:xx:7D WAN 2 : 70:4C:A5:xx:xx:7E LAN 1 : 70:4C:A5:xx:xx:7F LAN 2 : 70:4C:A5:xx:xx:80 LAN 3 : 70:4C:A5:xx:xx:81 LAN 4 : 70:4C:A5:xx:xx:82 LAN 5 : 70:4C:A5:xx:xx:83 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 12:54:14 +00:00
define Device/fortinet_fg-50e
mvebu: add common image definition for FortiGate devices Add a common definition of Fortinet FortiGate devices to image/cortexa9.mk for a preparation of adding support for other FortiGate 3xE/5xE devices. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-12-04 12:02:13 +00:00
$(Device/fortinet)
mvebu: add support for Fortinet FortiGate 50E Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-50E and interrupt to show bootmenu 2. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 3. Prepare TFTP server with the parameters obtained above 4. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 6. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 7. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 7. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 8. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of WAN1/2 are connected to GPIO expander. There is no way to indicate link speed of networking device on Linux Kernel/OpenWrt, so those LEDs cannot be handled like stock firmware. On OpenWrt, use netdev(link) trigger instead. - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex)) WAN 1 : 70:4C:A5:xx:xx:7D WAN 2 : 70:4C:A5:xx:xx:7E LAN 1 : 70:4C:A5:xx:xx:7F LAN 2 : 70:4C:A5:xx:xx:80 LAN 3 : 70:4C:A5:xx:xx:81 LAN 4 : 70:4C:A5:xx:xx:82 LAN 5 : 70:4C:A5:xx:xx:83 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 12:54:14 +00:00
DEVICE_MODEL := FortiGate 50E
mvebu: add common image definition for FortiGate devices Add a common definition of Fortinet FortiGate devices to image/cortexa9.mk for a preparation of adding support for other FortiGate 3xE/5xE devices. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-12-04 12:02:13 +00:00
DEVICE_DTS := armada-385-fortinet-fg-50e
mvebu: add support for Fortinet FortiGate 50E Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-50E and interrupt to show bootmenu 2. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 3. Prepare TFTP server with the parameters obtained above 4. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 6. Type "r" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 7. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 7. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 8. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of WAN1/2 are connected to GPIO expander. There is no way to indicate link speed of networking device on Linux Kernel/OpenWrt, so those LEDs cannot be handled like stock firmware. On OpenWrt, use netdev(link) trigger instead. - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex)) WAN 1 : 70:4C:A5:xx:xx:7D WAN 2 : 70:4C:A5:xx:xx:7E LAN 1 : 70:4C:A5:xx:xx:7F LAN 2 : 70:4C:A5:xx:xx:80 LAN 3 : 70:4C:A5:xx:xx:81 LAN 4 : 70:4C:A5:xx:xx:82 LAN 5 : 70:4C:A5:xx:xx:83 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 12:54:14 +00:00
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FGT50E
endef
TARGET_DEVICES += fortinet_fg-50e
mvebu: add support for Fortinet FortiGate 51E Fortinet FortiGate 51E (FG-51E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B)) - mode : SATA III 6Gbps - power : 3.3 VDC, 3.1 W (Max.) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2.5 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-51E and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "R" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 70:4C:A5:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex)) WAN 1 : 70:4C:A5:xx:xx:99 WAN 2 : 70:4C:A5:xx:xx:9A LAN 1 : 70:4C:A5:xx:xx:9B LAN 2 : 70:4C:A5:xx:xx:9C LAN 3 : 70:4C:A5:xx:xx:9D LAN 4 : 70:4C:A5:xx:xx:9E LAN 5 : 70:4C:A5:xx:xx:9F Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Tested-by: Raylynn Knight <rayknight@me.com>
2024-01-20 06:34:41 +00:00
define Device/fortinet_fg-51e
$(Device/fortinet)
DEVICE_MODEL := FortiGate 51E
DEVICE_DTS := armada-385-fortinet-fg-51e
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FGT51E
endef
TARGET_DEVICES += fortinet_fg-51e
mvebu: add support for Fortinet FortiGate 52E Fortinet FortiGate 52E (FG-52E) is a UTM, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - SSD : mSATA SSD 64 GB (2x A-DATA XM21E (AXM21ES3-32GM-B)) - mode : SATA III 6Gbps - power : 3.3 VDC, 3.1 W (Max.) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2.5 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FG-52E and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "R" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex)) WAN 1 : 90:6C:AC:xx:xx:99 WAN 2 : 90:6C:AC:xx:xx:9A LAN 1 : 90:6C:AC:xx:xx:9B LAN 2 : 90:6C:AC:xx:xx:9C LAN 3 : 90:6C:AC:xx:xx:9D LAN 4 : 90:6C:AC:xx:xx:9E LAN 5 : 90:6C:AC:xx:xx:9F Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-03-08 12:54:14 +00:00
define Device/fortinet_fg-52e
$(Device/fortinet)
DEVICE_MODEL := FortiGate 52E
DEVICE_DTS := armada-385-fortinet-fg-52e
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FGT52E
endef
TARGET_DEVICES += fortinet_fg-52e
mvebu: add support for Fortinet FortiWiFi 50E-2R Fortinet FortiWiFi 50E-2R (FWF-50E-2R) is a UTM with 2x WLAN, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Nanya NT5CC512M8EN-EK) - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - WLAN : Gemtek WMDQ-177ACN (Qualcomm Atheros QCA9892 (2T2R)) (2x) - interface : MiniPCIe - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2.5 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FWF-50E-2R and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "R" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex)) WAN 1 : 90:6C:AC:xx:xx:99 WAN 2 : 90:6C:AC:xx:xx:9A LAN 1 : 90:6C:AC:xx:xx:9B LAN 2 : 90:6C:AC:xx:xx:9C LAN 3 : 90:6C:AC:xx:xx:9D LAN 4 : 90:6C:AC:xx:xx:9E LAN 5 : 90:6C:AC:xx:xx:9F WLAN 1: 1C:49:7B:xx:xx:xx (MiniPCIe Card) WLAN 2: 1C:49:7B:xx:xx:xx (MiniPCIe Card) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Tested-by: Raylynn Knight <rayknight@me.com>
2023-03-08 12:54:14 +00:00
define Device/fortinet_fwf-50e-2r
$(Device/fortinet)
DEVICE_MODEL := FortiWiFi 50E-2R
DEVICE_DTS := armada-385-fortinet-fwf-50e-2r
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FW502R
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct \
wpad-basic-mbedtls
endef
TARGET_DEVICES += fortinet_fwf-50e-2r
mvebu: add support for Fortinet FortiWiFi 51E Fortinet FortiWiFi 51E (FWF-51E) is a UTM with 1x WLAN and 1x SSD, based on Armada 385 (88F6820). Specification: - SoC : Marvell Armada 385 88F6820 - RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ") - Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G) - SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B)) - mode : SATA III 6Gbps - power : 3.3 VDC, 3.1 W (Max.) - Ethernet : 7x 10/100/1000 Mbps - LAN 1-5 : Marvell 88E6176 - WAN 1, 2 : Marvell 88E1512 (2x) - WLAN : Fortinet EMP7618-FT (Atheros AR9382 (2T2R)) - interface : MiniPCIe - LEDs/Keys : 18x/1x - UART : "CONSOLE" port (RJ-45, RS-232C level) - port : ttyS0 - settings : 9600bps 8n1 - assignment : 1:NC , 2:NC , 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC , 8:NC - note : compatible with Cisco console cable - HW Monitoring: nuvoTon NCT7802Y - Power : 12 VDC, 2 A - plug : Molex 5557-02R Flash instruction using initramfs image: 1. Power on FWF-51E and interrupt to show bootmenu 2. Call "[I]: System information." -> "[S]: Set serial port baudrate." and set baudrate to 9600 bps 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and connect computer to "Image download port" in the parameters 4. Prepare TFTP server with the parameters obtained above 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP directory 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs image from TFTP server 7. Type "R" key when the following message is showed, to boot initramfs image without flashing to spi-nor flash "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?" 8. On initramfs image, backup mtd if needed minimum: - "firmware-info" - "kernel" - "rootfs" 9. On initramfs image, upload sysupgrade image to the device and perform sysupgrade 10. Wait ~200 seconds to complete flashing and rebooting. If the device is booted with stock firmware, login to bootmenu and call "[B]: Boot with backup firmware and set as default." to set the first OS image as default and boot it. Notes: - Both colors of Bi-color LEDs on the front panel cannot be turned on at the same time. - "PWR" and "Logo" LEDs are connected to power source directly. - The following partitions are added for OpenWrt. These partitions are contained in "uboot" partition (0x0-0x1fffff) on stock firmware. - "firmware-info" - "dtb" - "u-boot-env" - "board-info" Image header for bootmenu tftp: 0x0 - 0xf : ? 0x10 - 0x2f : Image Name 0x30 - 0x17f: ? 0x180 - 0x183: Kernel Offset* 0x184 - 0x187: Kernel Length* 0x188 - 0x18b: RootFS Offset (ext2)* 0x18c - 0x18f: RootFS Length (ext2)* 0x190 - 0x193: DTB Offset 0x194 - 0x197: DTB Length 0x198 - 0x19b: Data Offset (jffs2) 0x19c - 0x19f: Data Length (jffs2) 0x1a0 - 0x1ff: ? *: required for initramfs image MAC addresses: (eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex)) WAN 1 : 90:6C:AC:xx:xx:99 WAN 2 : 90:6C:AC:xx:xx:9A LAN 1 : 90:6C:AC:xx:xx:9B LAN 2 : 90:6C:AC:xx:xx:9C LAN 3 : 90:6C:AC:xx:xx:9D LAN 4 : 90:6C:AC:xx:xx:9E LAN 5 : 90:6C:AC:xx:xx:9F WLAN : 88:DC:96:xx:xx:xx (MiniPCIe Card) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Tested-by: Raylynn Knight <rayknight@me.com>
2023-03-08 12:54:14 +00:00
define Device/fortinet_fwf-51e
$(Device/fortinet)
DEVICE_MODEL := FortiWiFi 51E
DEVICE_DTS := armada-385-fortinet-fwf-51e
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FWF51E
DEVICE_PACKAGES += kmod-ath9k wpad-basic-mbedtls
endef
TARGET_DEVICES += fortinet_fwf-51e
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
define Device/globalscale_mirabox
$(Device/NAND-512K)
DEVICE_VENDOR := Globalscale
DEVICE_MODEL := Mirabox
SOC := armada-370
SUPPORTED_DEVICES += mirabox
endef
TARGET_DEVICES += globalscale_mirabox
mvebu: add support for IIJ SA-W2 Internet Initiative Japan Inc. (IIJ) SA-W2 is a network appliance with 11ac (Wi-Fi 5) wlan, based on 88F6810. Specification: - SoC : Marvell Armada 380 88F6810 - RAM : DDR3 256 MiB (Micron MT41K64M16TW-107:J x2) - Flash : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ) - WLAN : 2.4/5 GHz, Mini PCI-E - 2.4 GHz : Silex SX-PCEGN (Atheros AR9287 (2T2R)) - 5 GHz : Silex SX-PCEAC (Qualcomm Atheros QCA9880 (3T3R)) - Ethernet : 10/100/1000 Mbps x5 - Switch : Marvell 88E6172 - LEDs/Keys : 12x/1x - UART : "CONSOLE" port (RJ-45, RS-232C) - settings : 115200n8 - assignment: 1:NC, 2:NC, 3:TXD, 4:GND, 5:GND, 6:RXD, 7:NC, 8:NC - note : compatible with Cisco console cable - Power : DC Input or PoE - DC Input : 12 VDC, 3 A - PoE : 802.3af - module : Silvertel Ag9712-2BR - note : USB ports shouldn't be used when powered by PoE - Bootloader : PMON2000 based - Stock : NetBSD based Flash instruction using sysupgrade image: 1. Prepare TFTP server with IP address 192.168.0.10 and put sysupgrade image to TFTP directory 2. Connect PC to "GE0/PoE" port on SA-W2 3. Power on SA-W2, interrupt count-down by Esc and enter to bootloader CLI 4. Set IP address of the device address 192.168.0.1 5. Download sysupgrade image and flash to storage tftpload 192.168.0.10 <image name> firmwrite example: #tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin Loading openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin loaded 8127268 byte(s) #firmwrite Erasing FLASH block 32 Done 0x00200000. Erasing FLASH block 33 Done 0x00210000. ... Erasing FLASH block 155 Done 0x009b0000. Erasing FLASH block 156 Done 0x009c0000. Programming FLASH. Done. Verifying FLASH. No Errors found. 6. Check the flashed firmware firmcheck example: #firmcheck [Normal firmware] ident: 'SEIL2015' copyright: 'ARM OpenWrt Linux-5.15.93' version format: 1 version major: 9 version minor: 99 version release: 'r22060+36-5163bb5e54' body size: 3578524 checksum: 0x8a083cb8 [Rescue firmware] ident: 'SEIL2015' copyright: 'Copyright (c) 2017 Internet Initiative Japan Inc. All rights reserved.' version format: 1 version major: 3 version minor: 70 version release: 'Release' body size: 10152458 checksum: 0x8f9518c2 7. Boot with the flashed firmware boot Note: - The bootloader on this device is not U-Boot and it's environment space ("bootloader-env") has no compatibility with U-Boot tools. - eth1 is connected to port6 of 88E6172 switch, but multi-cpu port can't be handled on Linux Kernel and not defined. - Powering by PoE hasn't been tested yet. - This device has 2x OS images on flash and they can be switched by setting "BOOTDEV" variable on bootloader CLI. That variable supports the following values: - "flash" : primary image on flash ("firmware") - "rescue": secondary image on flash ("rescue") - "usb" : usb storage (broken?) - "lan0/1": network command to set: set BOOTDEV=<dev> example: set BOOTDEV=rescue This commit also supports booting from secondary partition. - To execute initramfs image on bootloader CLI, use "go" command. ("go" command is not listed on the output of "help", but available) example (download and execute): address 192.168.0.1 tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-initramfs-kernel.bin go MAC addresses: LAN : 00:E0:4D:xx:xx:19 (none) WAN : 00:E0:4D:xx:xx:18 (board_info, 0x6 (hex)) 2.4 GHz: 84:25:3F:xx:xx:xx (Mini PCI-E card) 5 GHz : 84:25:3F:xx:xx:xx (Mini PCI-E card) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-11-13 08:22:26 +00:00
define Device/iij_sa-w2
DEVICE_VENDOR := IIJ
DEVICE_MODEL := SA-W2
SOC := armada-380
KERNEL := kernel-bin | append-dtb | seil-header
DEVICE_DTS := armada-380-iij-sa-w2
IMAGE_SIZE := 15360k
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := kmod-ath9k kmod-ath10k-ct ath10k-firmware-qca988x-ct \
wpad-basic-mbedtls
endef
TARGET_DEVICES += iij_sa-w2
mvebu: add support for ipTIME NAS1dual ipTIME NAS1dual is a 1-bay NAS, based on Marvell Armada 385 SoC. Specifications: * SoC: 88F6820 * RAM: 2 GiB * Flash: SPI NOR 64 MiB * SATA: 1x 3Gb/s * Ethernet: 2x 1GbE * USB: 1x 3.0 * Fan: 2 speed level * UART: J11 (115200 8N1) * Pinout: [3V3] (TXD) (RXD) (GND) Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-01 14:47:43 +00:00
define Device/iptime_nas1dual
DEVICE_VENDOR := ipTIME
DEVICE_MODEL := NAS1dual
DEVICE_PACKAGES := kmod-hwmon-drivetemp kmod-hwmon-gpiofan kmod-usb3
SOC := armada-385
KERNEL := kernel-bin | append-dtb | iptime-naspkg nas1dual
KERNEL_SIZE := 6144k
IMAGES := sysupgrade.bin
IMAGE_SIZE := 64256k
IMAGE/sysupgrade.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
append-rootfs | pad-rootfs | check-size | append-metadata
endef
TARGET_DEVICES += iptime_nas1dual
mvebu: add Kobol Helios 4 device The Helios 4 is a NAS from Kobol that is powered by an Armada 38x MicroSOM from Solidrun, similarly to Clearfog. This device has: -Armada 38x CPU (dual core ARMv7 1.6 Ghz) -2 GB of ECC RAM -Gigabit ethernet (Marvell) -2x USB 3.0 ports -4x Sata 3.0 ports -i2c header (J9 |>GND|SDA|SCL|VCC) -2x 3-pin fan headers with PWM -micro-usb port is a TTL/UART to USB converter connected to TTL -MicroSD card slot -System, 4xSata and 1xUSB LEDs NOT WORKING: fan control Fan Control requires a kernel patch that is available in the Armbian project (the "default firmware" of this device) and named mvebu-gpio-remove-hardcoded -timer-assignment This patch isn't acceptable by OpenWrt, it should be upstreamed. I also have that patch in my own local OpenWrt builds, in case you want a more clean and less confusing patch for upstreaming. To install, write the disk image on a micro SD card with dd or win32 disk imager, insert the card in the slot. Check that the dip switch battery for boot selection is as follows Switch 1 and 2 down/off, switches 3, 4, 5 up/on. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-07-12 13:35:54 +00:00
define Device/kobol_helios4
DEVICE_VENDOR := Kobol
DEVICE_MODEL := Helios4
KERNEL_INSTALL := 1
KERNEL := kernel-bin
DEVICE_PACKAGES := mkf2fs e2fsprogs partx-utils
IMAGES := sdcard.img.gz
IMAGE/sdcard.img.gz := boot-scr | boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
SOC := armada-388
mvebu: cortexa9: use renamed U-boot binaries Due to upstream change in U-boot the binaries were renamed [1]. [1] https://source.denx.de/u-boot/u-boot/-/commit/87ac4b4b4ca5f00e2ddcdac41c9dc691ab2aecf1 Fixes: 2f83369e3e97 ("uboot-mvebu: update to version 2023.01") Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-19 08:10:41 +00:00
UBOOT := helios4-u-boot-with-spl.kwb
mvebu: add Kobol Helios 4 device The Helios 4 is a NAS from Kobol that is powered by an Armada 38x MicroSOM from Solidrun, similarly to Clearfog. This device has: -Armada 38x CPU (dual core ARMv7 1.6 Ghz) -2 GB of ECC RAM -Gigabit ethernet (Marvell) -2x USB 3.0 ports -4x Sata 3.0 ports -i2c header (J9 |>GND|SDA|SCL|VCC) -2x 3-pin fan headers with PWM -micro-usb port is a TTL/UART to USB converter connected to TTL -MicroSD card slot -System, 4xSata and 1xUSB LEDs NOT WORKING: fan control Fan Control requires a kernel patch that is available in the Armbian project (the "default firmware" of this device) and named mvebu-gpio-remove-hardcoded -timer-assignment This patch isn't acceptable by OpenWrt, it should be upstreamed. I also have that patch in my own local OpenWrt builds, in case you want a more clean and less confusing patch for upstreaming. To install, write the disk image on a micro SD card with dd or win32 disk imager, insert the card in the slot. Check that the dip switch battery for boot selection is as follows Switch 1 and 2 down/off, switches 3, 4, 5 up/on. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-07-12 13:35:54 +00:00
BOOT_SCRIPT := clearfog
endef
TARGET_DEVICES += kobol_helios4
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
define Device/linksys
$(Device/NAND-128K)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_VENDOR := Linksys
treewide: replace wpad-basic-wolfssl default The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-12-28 04:44:11 +00:00
DEVICE_PACKAGES := kmod-mwlwifi wpad-basic-mbedtls
mvebu: image: improve readability of device recipes Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:31 +00:00
IMAGES += factory.img
mvebu: move definition of factory.img out of Device/Default The Device/Default definition in mvebu defines an IMAGE/factory.img which is not included in IMAGES, and only used twice in the individual definitions. Move it out of the default definition to keep it closer to the reassignment of IMAGES and make it more consistent with respect to other values of IMAGE/factory.img Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-24 17:56:23 +00:00
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
append-ubi | pad-to $$$$(PAGESIZE)
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
KERNEL_SIZE := 6144k
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/linksys_wrt1200ac
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
$(call Device/linksys)
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
$(Device/dsa-migration)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_MODEL := WRT1200AC
DEVICE_ALT0_VENDOR := Linksys
DEVICE_ALT0_MODEL := Caiman
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
DEVICE_DTS := armada-385-linksys-caiman
DEVICE_PACKAGES += mwlwifi-firmware-88w8864
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-385-linksys-caiman linksys,caiman
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += linksys_wrt1200ac
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
define Device/linksys_wrt1900acs
$(call Device/linksys)
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
$(Device/dsa-migration)
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
DEVICE_MODEL := WRT1900ACS
DEVICE_VARIANT := v1
DEVICE_ALT0_VENDOR := Linksys
DEVICE_ALT0_MODEL := WRT1900ACS
DEVICE_ALT0_VARIANT := v2
DEVICE_ALT1_VENDOR := Linksys
DEVICE_ALT1_MODEL := Shelby
DEVICE_DTS := armada-385-linksys-shelby
DEVICE_PACKAGES += mwlwifi-firmware-88w8864
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-385-linksys-shelby linksys,shelby
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
endef
TARGET_DEVICES += linksys_wrt1900acs
mvebu: rename Linksys devices based on their common names The Linksys devices in mvebu target feature a mixed naming, where parts are based on the official product name (device node, image; e.g. WRT3200ACM) and parts are based on the internal code name (DTS file name, compatible, LED labels; e.g. rango). This inconsistent naming has been perceived as quite confusing. A recent attempt by Paul Spooren to harmonize this naming in kernel has been declined there. However, for us it still makes sense to apply at least a part of these changes locally. Primarily, this patch changes the compatible in DTS and thus the board name used in various scripts to have them in line with the device, model and image names. Due to the recent switch from swconfig to DSA, this allows us to drop SUPPORTED_DEVICES and thus prevent seamless upgrade between these incompatible setups. However, this does not include the LED label rename from Paul's initial patch: I don't think it's worth keeping the enormous diff locally for this case, as we can implement this much easier in 01_leds if we have to live with the inconsistency anyway. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, extend to all devices, drop DT LED changes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-10 10:14:21 +00:00
define Device/linksys_wrt1900ac-v1
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
$(call Device/linksys)
mvebu: mamba resize kernel to 4MB mamba has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. mamba uboot however as set from factory will load up to 4MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0xa00000, size 0x400000 4194304 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "pri_kern_size"; pri_kern_size=0x400000 Resize the root partitions from 37MB to 36MB to let kernel expand into it another 1MB. And set kernel target size to 4MB. Lastly add a compatibility version message: kernel-size-migration. And set it on mamba to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-02-06 03:38:03 +00:00
$(Device/kernel-size-migration)
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
DEVICE_MODEL := WRT1900AC
DEVICE_VARIANT := v1
DEVICE_ALT0_VENDOR := Linksys
DEVICE_ALT0_MODEL := Mamba
DEVICE_DTS := armada-xp-linksys-mamba
DEVICE_PACKAGES += mwlwifi-firmware-88w8864
mvebu: mamba resize kernel to 4MB mamba has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. mamba uboot however as set from factory will load up to 4MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0xa00000, size 0x400000 4194304 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "pri_kern_size"; pri_kern_size=0x400000 Resize the root partitions from 37MB to 36MB to let kernel expand into it another 1MB. And set kernel target size to 4MB. Lastly add a compatibility version message: kernel-size-migration. And set it on mamba to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-02-06 03:38:03 +00:00
KERNEL_SIZE := 4096k
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-xp-linksys-mamba linksys,mamba
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
endef
mvebu: only disable WRT1900AC v1 and WRT32X for buildbots Use "DEFAULT := n" to only disable devices for buildbots, but keep them available for manual build. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 09:05:25 +00:00
TARGET_DEVICES += linksys_wrt1900ac-v1
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
mvebu: rename Linksys devices based on their common names The Linksys devices in mvebu target feature a mixed naming, where parts are based on the official product name (device node, image; e.g. WRT3200ACM) and parts are based on the internal code name (DTS file name, compatible, LED labels; e.g. rango). This inconsistent naming has been perceived as quite confusing. A recent attempt by Paul Spooren to harmonize this naming in kernel has been declined there. However, for us it still makes sense to apply at least a part of these changes locally. Primarily, this patch changes the compatible in DTS and thus the board name used in various scripts to have them in line with the device, model and image names. Due to the recent switch from swconfig to DSA, this allows us to drop SUPPORTED_DEVICES and thus prevent seamless upgrade between these incompatible setups. However, this does not include the LED label rename from Paul's initial patch: I don't think it's worth keeping the enormous diff locally for this case, as we can implement this much easier in 01_leds if we have to live with the inconsistency anyway. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, extend to all devices, drop DT LED changes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-10 10:14:21 +00:00
define Device/linksys_wrt1900ac-v2
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
$(call Device/linksys)
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
$(Device/dsa-migration)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_MODEL := WRT1900AC
DEVICE_VARIANT := v2
DEVICE_ALT0_VENDOR := Linksys
DEVICE_ALT0_MODEL := Cobra
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
DEVICE_DTS := armada-385-linksys-cobra
DEVICE_PACKAGES += mwlwifi-firmware-88w8864
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-385-linksys-cobra linksys,cobra
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: rename Linksys devices based on their common names The Linksys devices in mvebu target feature a mixed naming, where parts are based on the official product name (device node, image; e.g. WRT3200ACM) and parts are based on the internal code name (DTS file name, compatible, LED labels; e.g. rango). This inconsistent naming has been perceived as quite confusing. A recent attempt by Paul Spooren to harmonize this naming in kernel has been declined there. However, for us it still makes sense to apply at least a part of these changes locally. Primarily, this patch changes the compatible in DTS and thus the board name used in various scripts to have them in line with the device, model and image names. Due to the recent switch from swconfig to DSA, this allows us to drop SUPPORTED_DEVICES and thus prevent seamless upgrade between these incompatible setups. However, this does not include the LED label rename from Paul's initial patch: I don't think it's worth keeping the enormous diff locally for this case, as we can implement this much easier in 01_leds if we have to live with the inconsistency anyway. Signed-off-by: Paul Spooren <mail@aparcar.org> [rebase, extend to all devices, drop DT LED changes] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-10 10:14:21 +00:00
TARGET_DEVICES += linksys_wrt1900ac-v2
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/linksys_wrt3200acm
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
$(call Device/linksys)
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
$(Device/dsa-migration)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_MODEL := WRT3200ACM
DEVICE_ALT0_VENDOR := Linksys
DEVICE_ALT0_MODEL := Rango
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
DEVICE_DTS := armada-385-linksys-rango
DEVICE_PACKAGES += kmod-btmrvl kmod-mwifiex-sdio mwlwifi-firmware-88w8964
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-385-linksys-rango linksys,rango
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += linksys_wrt3200acm
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/linksys_wrt32x
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
$(call Device/linksys)
mvebu: venom resize kernel to 6MB venom has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. venom uboot however as set from factory will load up to 6MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0x900000, size 0x600000 6291456 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "priKernSize"; priKernSize=0x0600000 Resize the root partitions from 120MB to 117MB to let kernel expand into it another 3MB. And set kernel target size to 6MB. Lastly set the kernel-size-migration compatibility version on venom to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-02-06 03:42:47 +00:00
$(Device/kernel-size-migration)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_MODEL := WRT32X
DEVICE_ALT0_VENDOR := Linksys
DEVICE_ALT0_MODEL := Venom
mvebu: add support for WRT32X (venom) Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-13 13:29:30 +00:00
DEVICE_DTS := armada-385-linksys-venom
DEVICE_PACKAGES += kmod-btmrvl kmod-mwifiex-sdio mwlwifi-firmware-88w8964
mvebu: venom resize kernel to 6MB venom has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. venom uboot however as set from factory will load up to 6MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0x900000, size 0x600000 6291456 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "priKernSize"; priKernSize=0x0600000 Resize the root partitions from 120MB to 117MB to let kernel expand into it another 3MB. And set kernel target size to 6MB. Lastly set the kernel-size-migration compatibility version on venom to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-02-06 03:42:47 +00:00
KERNEL_SIZE := 6144k
mvebu: add support for WRT32X (venom) Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-13 13:29:30 +00:00
KERNEL := kernel-bin | append-dtb
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-385-linksys-venom linksys,venom
mvebu: add support for WRT32X (venom) Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-13 13:29:30 +00:00
endef
mvebu: only disable WRT1900AC v1 and WRT32X for buildbots Use "DEFAULT := n" to only disable devices for buildbots, but keep them available for manual build. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 09:05:25 +00:00
TARGET_DEVICES += linksys_wrt32x
mvebu: add support for WRT32X (venom) Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-13 13:29:30 +00:00
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/marvell_a370-db
mvebu: image: improve readability of device recipes Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:31 +00:00
$(Device/NAND-512K)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_VENDOR := Marvell
DEVICE_MODEL := Armada 370 Development Board (DB-88F6710-BP-DDR3)
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
DEVICE_DTS := armada-370-db
mvebu: use device-tree board detection Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:34 +00:00
SUPPORTED_DEVICES += armada-370-db
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += marvell_a370-db
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/marvell_a370-rd
mvebu: image: improve readability of device recipes Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:31 +00:00
$(Device/NAND-512K)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_VENDOR := Marvell
DEVICE_MODEL := Armada 370 RD (RD-88F6710-A1)
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
DEVICE_DTS := armada-370-rd
mvebu: use device-tree board detection Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:34 +00:00
SUPPORTED_DEVICES += armada-370-rd
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += marvell_a370-rd
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
define Device/marvell_a385-db-ap
$(Device/NAND-256K)
DEVICE_VENDOR := Marvell
DEVICE_MODEL := Armada 385 Development Board AP (DB-88F6820-AP)
DEVICE_DTS := armada-385-db-ap
IMAGES += factory.img
mvebu: move definition of factory.img out of Device/Default The Device/Default definition in mvebu defines an IMAGE/factory.img which is not included in IMAGES, and only used twice in the individual definitions. Move it out of the default definition to keep it closer to the reassignment of IMAGES and make it more consistent with respect to other values of IMAGE/factory.img Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-24 17:56:23 +00:00
IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
append-ubi | pad-to $$$$(PAGESIZE)
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
KERNEL_SIZE := 8192k
SUPPORTED_DEVICES += armada-385-db-ap
endef
TARGET_DEVICES += marvell_a385-db-ap
define Device/marvell_a388-rd
DEVICE_VENDOR := Marvell
DEVICE_MODEL := Armada 388 RD (RD-88F6820-AP)
DEVICE_DTS := armada-388-rd
IMAGES := firmware.bin
IMAGE/firmware.bin := append-kernel | pad-to 256k | append-rootfs | pad-rootfs
SUPPORTED_DEVICES := armada-388-rd marvell,a385-rd
endef
TARGET_DEVICES += marvell_a388-rd
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/marvell_axp-db
mvebu: image: improve readability of device recipes Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:31 +00:00
$(Device/NAND-512K)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_VENDOR := Marvell
DEVICE_MODEL := Armada XP Development Board (DB-78460-BP)
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
DEVICE_DTS := armada-xp-db
mvebu: use device-tree board detection Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:34 +00:00
SUPPORTED_DEVICES += armada-xp-db
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += marvell_axp-db
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/marvell_axp-gp
mvebu: image: improve readability of device recipes Drop overly complex amount of defines wich are referenced in the same devices pool and move image recipes to common define, since devices not using them overwrite it. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:31 +00:00
$(Device/NAND-512K)
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_VENDOR := Marvell
DEVICE_MODEL := Armada Armada XP GP (DB-MV784MP-GP)
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
DEVICE_DTS := armada-xp-gp
mvebu: use device-tree board detection Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:34 +00:00
SUPPORTED_DEVICES += armada-xp-gp
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += marvell_axp-gp
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
define Device/plathome_openblocks-ax3-4
DEVICE_VENDOR := Plat'Home
DEVICE_MODEL := OpenBlocks AX3
DEVICE_VARIANT := 4 ports
SOC := armada-xp
SUPPORTED_DEVICES += openblocks-ax3-4
BLOCKSIZE := 128k
PAGESIZE := 1
IMAGES += factory.img
IMAGE/factory.img := append-kernel | pad-to $$(BLOCKSIZE) | append-ubi
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
TARGET_DEVICES += plathome_openblocks-ax3-4
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
define Device/solidrun_clearfog-base-a1
mvebu: split up DEVICE_TITLE DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-09-09 22:13:30 +00:00
DEVICE_VENDOR := SolidRun
DEVICE_MODEL := ClearFog Base
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
KERNEL_INSTALL := 1
KERNEL := kernel-bin
mvebu: sysupgrade: sdcard: keep user added partitons Currently sysupgrade overwrites whole disk and destroys partitions added by user. Sync the sysupgrade code with the one present in x86 target to remedy this behaviour. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-28 17:07:09 +00:00
DEVICE_PACKAGES := mkf2fs e2fsprogs partx-utils
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
IMAGES := sdcard.img.gz
mvebu: use ext4 for clearfog image bootfs This will allow to drop additional packages and shrink image size. Cc: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-28 17:07:06 +00:00
IMAGE/sdcard.img.gz := boot-scr | boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
mvebu: image: introduce BOOT_SCRIPT variable All of U-Boot scripts repeat the same pattern with only Device Tree blob name changing for respective device. Therefore create generic scripts which will be altered on demad by image build process, and create BOOT_SCRIPT variable which can be added to device recipe and will allow referencing the same script by many device recipes. This will allow to slim down the ammount of files in buildroot tree and avoid needlessly incrementing amount of boot scripts if new devices will be added. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:30 +00:00
DEVICE_DTS := armada-388-clearfog-base armada-388-clearfog-pro
mvebu: cortexa9: use renamed U-boot binaries Due to upstream change in U-boot the binaries were renamed [1]. [1] https://source.denx.de/u-boot/u-boot/-/commit/87ac4b4b4ca5f00e2ddcdac41c9dc691ab2aecf1 Fixes: 2f83369e3e97 ("uboot-mvebu: update to version 2023.01") Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-19 08:10:41 +00:00
UBOOT := clearfog-u-boot-with-spl.kwb
mvebu: image: introduce BOOT_SCRIPT variable All of U-Boot scripts repeat the same pattern with only Device Tree blob name changing for respective device. Therefore create generic scripts which will be altered on demad by image build process, and create BOOT_SCRIPT variable which can be added to device recipe and will allow referencing the same script by many device recipes. This will allow to slim down the ammount of files in buildroot tree and avoid needlessly incrementing amount of boot scripts if new devices will be added. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:30 +00:00
BOOT_SCRIPT := clearfog
mvebu: increase compat version for SolidRun ClearFog Base When changing the Pro variant to DSA, the ethernet interface rename script was dropped by all devices to keep them in sync: be309bfd7445 ("mvebu: drop 06_set_iface_mac preinit script") Therefore, network config will be broken after upgrade for the Base variant as well. Increase the compat version and provide a message to signal that to the users. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 09:21:34 +00:00
SUPPORTED_DEVICES += armada-388-clearfog-base
DEVICE_COMPAT_VERSION := 1.1
DEVICE_COMPAT_MESSAGE := Ethernet interface rename has been dropped
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: align device names to vendor_device format Add vendors in device names and also rename few device names, for easier identyfying potential firmware to flash. The vendor and device string is mainly derived from model/compatipble string in dts from particular device, but since not all devices are well described, some of the renames follow marketing names. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 17:37:33 +00:00
TARGET_DEVICES += solidrun_clearfog-base-a1
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
define Device/solidrun_clearfog-pro-a1
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
$(Device/dsa-migration)
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
DEVICE_VENDOR := SolidRun
DEVICE_MODEL := ClearFog Pro
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
KERNEL_INSTALL := 1
KERNEL := kernel-bin
mvebu: remove swconfig package Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-19 08:16:32 +00:00
DEVICE_PACKAGES := mkf2fs e2fsprogs partx-utils
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
IMAGES := sdcard.img.gz
IMAGE/sdcard.img.gz := boot-scr | boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
DEVICE_DTS := armada-388-clearfog-pro armada-388-clearfog-base
mvebu: cortexa9: use renamed U-boot binaries Due to upstream change in U-boot the binaries were renamed [1]. [1] https://source.denx.de/u-boot/u-boot/-/commit/87ac4b4b4ca5f00e2ddcdac41c9dc691ab2aecf1 Fixes: 2f83369e3e97 ("uboot-mvebu: update to version 2023.01") Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-19 08:10:41 +00:00
UBOOT := clearfog-u-boot-with-spl.kwb
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
BOOT_SCRIPT := clearfog
mvebu: implement compatibility version for DSA migration This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 14:11:22 +00:00
SUPPORTED_DEVICES += armada-388-clearfog armada-388-clearfog-pro
mvebu: Add subtarget for Cortex A9 build This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-07 21:10:01 +00:00
endef
mvebu: image: sort devices alphabetically This sorts the devices in image Makefiles alphabetically. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed sorting in one case, add commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-31 15:46:13 +00:00
TARGET_DEVICES += solidrun_clearfog-pro-a1
mvebu: add support for Synology DS213j The Synology DS213j is a rather dated dual-bay SATA NAS based on on the Marvell Armada-370 SoC. It has long been supported in vanilla Linux, however, flash partitioning there didn't match with reality (ie. the bootloaders expectations) and nobody cared to wrap up OpenWrt support for the device. CPU: Marvell Armada-370 ARMv7 SoC @ 1200 MHz RAM: 512 MB DDR3 Flash: 8 MB (Micron Technology N25Q064) Network: 1x 1000M/100M/10M Ethernet (Marvell 88E1510) SATA: 2x 3.0Gbps USB: 2x USB 2.0 As OS options are becoming limited on that still quite useful hardware, patch the flash partitions to be able to get the most out of it when using OpenWrt. The vendor firmware loads kernel and initrd from fixed addresses in the flash, not making use of a modifyable environment stored in flash which is stored at a location right in the middle of the vendor's zImage partition (at 0x100000). Stock firmware flash layout: 0x000000 ~ 0x0c0000 : "RedBoot" (actually U-Boot) 0x0c0000 ~ 0x390000 : "zImage" 0x390000 ~ 0x7d0000 : "rd.gz" 0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no) 0x7e0000 ~ 0x7f0000 : "RedBoot Config" (unused? legacy left-over) 0x7f0000 ~ 0x800000 : "FIS directory" (unused? legacy left-over) OpenWrt flash layout: 0x000000 ~ 0x0c0000 : "u-boot" 0x0c0000 ~ 0x100000 : "gap" 0x100000 ~ 0x110000 : "u-boot-env" 0x110000 ~ 0x7d0000 : "kernel" 0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no) 0x7e0000 ~ 0x800000 : "gap2" "kernel", "gap" and "gap2" are concatenated using the mtd-concat virtual MTD driver, resulting in a partition "firmware" used by OpenWrt for kernel, rootfs and rootfs-overlay, 0x720000 (7296kiB) in total. Installation: 1. Connect to internal serial console port and Ethernet port, providing a TFTP server at a static IPv4 address, e.g. 192.168.1.254/24. 2. Interrupt bootloader using CTRL+C 3. Configure bootloader to load OpenWrt on future boot: setenv bootcmd "bootm f4110000" saveenv 4. Load and boot initramfs image via TFTP: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.254 tftpboot openwrt-mvebu-cortexa9-synology_ds213j-initramfs-kernel.bin bootm 5. Use sysupgrade to load final image. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-19 22:01:47 +00:00
define Device/synology_ds213j
DEVICE_VENDOR := Synology
DEVICE_MODEL := DS213j
KERNEL_SIZE := 6912k
IMAGE_SIZE := 7168k
FILESYSTEMS := squashfs ubifs
KERNEL := kernel-bin | append-dtb | uImage none
KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
DEVICE_DTS := armada-370-synology-ds213j
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
check-size | append-metadata
DEVICE_PACKAGES := \
kmod-rtc-s35390a kmod-hwmon-gpiofan kmod-hwmon-drivetemp \
kmod-md-raid0 kmod-md-raid1 kmod-md-mod e2fsprogs mdadm \
mvebu: cortexa9: drop removal of firewall4 package Drop removal of firewall4 package for Synology DS213j device. With OPKG the firewall4 package was installed anyway as it's a dependency of luci-app-firewall and was silently installed again later in such condition. Drop it to fix support for APK. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-10-30 09:23:10 +00:00
-ppp -kmod-nft-offload -dnsmasq -odhcpd-ipv6only
mvebu: add support for Synology DS213j The Synology DS213j is a rather dated dual-bay SATA NAS based on on the Marvell Armada-370 SoC. It has long been supported in vanilla Linux, however, flash partitioning there didn't match with reality (ie. the bootloaders expectations) and nobody cared to wrap up OpenWrt support for the device. CPU: Marvell Armada-370 ARMv7 SoC @ 1200 MHz RAM: 512 MB DDR3 Flash: 8 MB (Micron Technology N25Q064) Network: 1x 1000M/100M/10M Ethernet (Marvell 88E1510) SATA: 2x 3.0Gbps USB: 2x USB 2.0 As OS options are becoming limited on that still quite useful hardware, patch the flash partitions to be able to get the most out of it when using OpenWrt. The vendor firmware loads kernel and initrd from fixed addresses in the flash, not making use of a modifyable environment stored in flash which is stored at a location right in the middle of the vendor's zImage partition (at 0x100000). Stock firmware flash layout: 0x000000 ~ 0x0c0000 : "RedBoot" (actually U-Boot) 0x0c0000 ~ 0x390000 : "zImage" 0x390000 ~ 0x7d0000 : "rd.gz" 0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no) 0x7e0000 ~ 0x7f0000 : "RedBoot Config" (unused? legacy left-over) 0x7f0000 ~ 0x800000 : "FIS directory" (unused? legacy left-over) OpenWrt flash layout: 0x000000 ~ 0x0c0000 : "u-boot" 0x0c0000 ~ 0x100000 : "gap" 0x100000 ~ 0x110000 : "u-boot-env" 0x110000 ~ 0x7d0000 : "kernel" 0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no) 0x7e0000 ~ 0x800000 : "gap2" "kernel", "gap" and "gap2" are concatenated using the mtd-concat virtual MTD driver, resulting in a partition "firmware" used by OpenWrt for kernel, rootfs and rootfs-overlay, 0x720000 (7296kiB) in total. Installation: 1. Connect to internal serial console port and Ethernet port, providing a TFTP server at a static IPv4 address, e.g. 192.168.1.254/24. 2. Interrupt bootloader using CTRL+C 3. Configure bootloader to load OpenWrt on future boot: setenv bootcmd "bootm f4110000" saveenv 4. Load and boot initramfs image via TFTP: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.254 tftpboot openwrt-mvebu-cortexa9-synology_ds213j-initramfs-kernel.bin bootm 5. Use sysupgrade to load final image. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-19 22:01:47 +00:00
endef
TARGET_DEVICES += synology_ds213j
Reference in New Issue Copy Permalink