ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-22 15:02:32 +00:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
417b76b1f1
openwrt/target/linux/ipq807x/Makefile

22 lines
514 B
Makefile
Raw Normal View History

ipq807x: add Qualcomm Atheros IPQ807x target Qualcomm Atheros IPQ807x is a modern WiSoC featuring: * Quad Core ARMv8 Cortex A-53 * @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye * @ 1.4 GHz (IPQ8070A/1A) Codename Acorn * Dual Band simultaneaous IEEE 802.11ax * 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A) * 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A) * 5G: 2x2/80MHz (IPQ8070A) * 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A) * 2G: 2x2/40MHz (IPQ8070A/1A) * 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports) * 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye * 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn * DDR3L/4 32/16 bit up to 2400MT/s * SDIO 3.0/SD card 3.0/eMMC 5.1 * Dual USB 3.0 * One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane) * Parallel NAND (ONFI)/LCD * 6x QUP BLSP SPI/I2C/UART * I2S, PCM, and TDMA * HW PWM * 1.8V configurable GPIO * Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc) Note that only v2 SOC models aka the ones ending with A suffix are supported, v1 models do not comply to the final 802.11ax and have lower clocks, lack the Gen3 PCIe etc. SoC itself has two UBI32 cores for the NSS offloading system, however currently no offloading is supported. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-02-05 22:40:51 +00:00
include $(TOPDIR)/rules.mk
ARCH:=aarch64
BOARD:=ipq807x
BOARDNAME:=Qualcomm Atheros IPQ807x
ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2022-01-01 22:20:19 +00:00
FEATURES:=squashfs ramdisk fpu nand rtc emmc
ipq807x: add Qualcomm Atheros IPQ807x target Qualcomm Atheros IPQ807x is a modern WiSoC featuring: * Quad Core ARMv8 Cortex A-53 * @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye * @ 1.4 GHz (IPQ8070A/1A) Codename Acorn * Dual Band simultaneaous IEEE 802.11ax * 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A) * 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A) * 5G: 2x2/80MHz (IPQ8070A) * 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A) * 2G: 2x2/40MHz (IPQ8070A/1A) * 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports) * 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye * 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn * DDR3L/4 32/16 bit up to 2400MT/s * SDIO 3.0/SD card 3.0/eMMC 5.1 * Dual USB 3.0 * One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane) * Parallel NAND (ONFI)/LCD * 6x QUP BLSP SPI/I2C/UART * I2S, PCM, and TDMA * HW PWM * 1.8V configurable GPIO * Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc) Note that only v2 SOC models aka the ones ending with A suffix are supported, v1 models do not comply to the final 802.11ax and have lower clocks, lack the Gen3 PCIe etc. SoC itself has two UBI32 cores for the NSS offloading system, however currently no offloading is supported. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-02-05 22:40:51 +00:00
KERNELNAME:=Image dtbs
CPU_TYPE:=cortex-a53
SUBTARGETS:=generic
KERNEL_PATCHVER:=5.15
include $(INCLUDE_DIR)/target.mk
DEFAULT_PACKAGES += \
kmod-usb3 kmod-usb-dwc3 kmod-usb-dwc3-qcom \
kmod-leds-gpio kmod-gpio-button-hotplug \
ipq807x: move AQR driver from built-in to kmod ipq807x does not compile-in hwmon core, and this is leading to the hwmon code in AQR driver not being compiled due to IS_REACHABLE(CONFIG_HWMON) evaluating to false as hwmon is being built as a module. So, lets not compile-in Aquantia PHY driver so it can be included as kmod instead to have functioning hwmon. This allows using the thermal sensors in AQR-s as thermal zones for cooling devices like fans. Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-02-15 16:05:30 +00:00
kmod-phy-aquantia kmod-qca-nss-dp \
ipq807x: include ath11k-ahb by default All of the IPQ807x devices support having 2 radios, so lets include the required driver as well. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-16 10:41:02 +00:00
ath11k-firmware-ipq8074 kmod-ath11k-ahb \
treewide: replace wpad-basic-wolfssl default The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-12-28 04:44:11 +00:00
wpad-basic-mbedtls uboot-envtools
ipq807x: add Qualcomm Atheros IPQ807x target Qualcomm Atheros IPQ807x is a modern WiSoC featuring: * Quad Core ARMv8 Cortex A-53 * @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye * @ 1.4 GHz (IPQ8070A/1A) Codename Acorn * Dual Band simultaneaous IEEE 802.11ax * 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A) * 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A) * 5G: 2x2/80MHz (IPQ8070A) * 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A) * 2G: 2x2/40MHz (IPQ8070A/1A) * 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports) * 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye * 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn * DDR3L/4 32/16 bit up to 2400MT/s * SDIO 3.0/SD card 3.0/eMMC 5.1 * Dual USB 3.0 * One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane) * Parallel NAND (ONFI)/LCD * 6x QUP BLSP SPI/I2C/UART * I2S, PCM, and TDMA * HW PWM * 1.8V configurable GPIO * Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc) Note that only v2 SOC models aka the ones ending with A suffix are supported, v1 models do not comply to the final 802.11ax and have lower clocks, lack the Gen3 PCIe etc. SoC itself has two UBI32 cores for the NSS offloading system, however currently no offloading is supported. Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-02-05 22:40:51 +00:00
$(eval $(call BuildTarget))
Reference in New Issue Copy Permalink