5.8 KiB
IMPORTANT pre-conditions:
- Install Vivado 2021.1. Make sure install Vitis as well. You should have this directory: your_Xilinx_install_directory/Vitis (NOT Vitis_HLS!)
- If the Vitis is not installed, you can add it by running "Xilinx Design Tools --> Add Design Tools for Devices 2021.1" from Xilinx program group/menu in your OS start menu, or Help menu of Vivado.
- SD card at least with 16GB
- Install packages:
sudo apt install flex bison libssl-dev device-tree-compiler u-boot-tools -y
[Use openwifi prebuilt img] [Build SD card from scratch] [Use existing SD card on new board]
Use openwifi prebuilt img
Download openwifi pre-built img (see Quick start), and extract it to .img file.
Use dd command to flash the SD card. (Or other software like Startup Disk Creator in Ubuntu)
sudo dd bs=512 count=31116288 if=openwifi-xyz.img of=/dev/your_sdcard_dev
To have correct count value, better to check the .img file actual situation by "fdisk -l img_filename".
Then start from the 2nd step of the Quick start in README.
Build SD card from scratch
Download image_2022-08-04-ADI-Kuiper-full.zip from https://wiki.analog.com/resources/tools-software/linux-software/kuiper-linux?redirect=1
Extract it to .img file.
Use dd command to flash the SD card. (Or other software like Startup Disk Creator in Ubuntu)
sudo dd bs=512 count=24018944 if=2022-08-04-ADI-Kuiper-full.img of=/dev/your_sdcard_dev
(To have correct count value, better to check the .img file actual situation by "fdisk -l img_filename". While making .img from SD card, check the SD card dev instead)
Mount the BOOT and rootfs partition of SD card to your computer.
Change the SD card file: Add following into rootfs/etc/network/interfaces
# The loopback interface
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
#your static IP
address 192.168.10.122
#your gateway IP
gateway 192.168.10.1
netmask 255.255.255.0
#your network address "family"
network 192.168.10.0
broadcast 192.168.10.255
Change the SD card file: Add following into rootfs/etc/sysctl.conf
net.ipv4.ip_forward=1
Change the SD card file: Add following into rootfs/etc/systemd/system.conf
DefaultTimeoutStopSec=2s
Put the openwifi/kernel_boot/10-network-device.rules into rootfs/etc/udev/rules.d/
Run update_sdcard.sh from openwifi/user_space directory to further prepare the SD card. The last argument $SDCARD_DIR of the script is the directory (mounting point) on your computer that has BOOT and rootfs directories/partitions.
The script will build and put following things into the SD card:
- Linux kernel image file (Update Driver):
- adi-linux-64/arch/arm64/boot/Image (64bit)
- adi-linux/arch/arm/boot/uImage (32bit)
- devicetree file:
- openwifi/kernel_boot/boards/zcu102_fmcs2/system.dtb (64bit)
- openwifi/kernel_boot/boards/$BOARD_NAME/devicetree.dtb (32bit)
- BOOT.BIN (Update FPGA):
- openwifi/kernel_boot/boards/$BOARD_NAME/output_boot_bin/BOOT.BIN
- openwifi driver (Update Driver).
- openwifi/user_space files and openwifi/webserver files
After update_sdcard.sh finishes, please do the 2nd step "Config the correct files ..." in Quick start. Then power on the board with the SD card, connect the board to your host PC (static IP 192.168.10.1) via ethernet, and ssh to the board with password "analog"
ssh root@192.168.10.122
Then change password to "openwifi" via "passwd" command onbard.
Enlarge the onboard SD disk space, and reboot (https://github.com/analogdevicesinc/adi-kuiper-gen/releases)
raspi-config --expand-rootfs
reboot now
Setup routing/NAT on the PC for your board -- this internet connection is important for post installation/config.
sudo sysctl -w net.ipv4.ip_forward=1
sudo iptables -t nat -A POSTROUTING -o NICY -j MASQUERADE
sudo ip route add 192.168.13.0/24 via 192.168.10.122 dev ethX
ethX is the PC NIC name connecting the board ethernet. NICY is the PC NIC name connecting internet (WiFi or another ethernet).
If you want, uncommenting "net.ipv4.ip_forward=1" in /etc/sysctl.conf to make IP forwarding persistent on PC.
Test the connectivity. Run on board (in the ssh session):
route add default gw 192.168.10.1
ping IP_YOU_KNOW_ON_YOUR_NETWORK
If there is issue with the connectivity (ping can not reach the target), it needs to be solved before going to the next step.
Do misc configurations/installations in the ssh session onboard:
sudo apt update
chmod +x /root/openwifi/*.sh
# install and setup dhcp server
sudo apt-get -y install isc-dhcp-server
cp /root/openwifi/dhcpd.conf /etc/dhcp/dhcpd.conf
# install hostapd and other useful tools
sudo apt-get -y install hostapd
sudo apt-get -y install tcpdump
sudo apt-get -y install webfs
sudo apt-get -y install iperf
sudo apt-get -y install iperf3
sudo apt-get -y install libpcap-dev
sudo apt-get -y install bridge-utils
# build on board tools
sudo apt-get -y install libnl-3-dev
sudo apt-get -y install libnl-genl-3-dev
cd /root/openwifi/sdrctl_src
make clean
make
cp sdrctl ../
cd /root/openwifi/side_ch_ctl_src/
gcc -o side_ch_ctl side_ch_ctl.c
cp side_ch_ctl ../
cd /root/openwifi/inject_80211/
make clean
make
cd ..
Run openwifi in the ssh session onboard:
/root/openwifi/setup_once.sh (Only need to run once for new board)
cd /root/openwifi
./wgd.sh
ifconfig sdr0 up
iwlist sdr0 scan
./fosdem.sh
Use existing SD card on new board
Just operate the existing/working SD card of the old board on your computer starting from the 2nd step of the Quick start in README. Then start using the SD card on the new board.