open-source IEEE 802.11 WiFi baseband FPGA (chip) design: driver, software
Go to file
2021-04-06 18:04:47 +02:00
adi-linux@b6e379910a track openwifi-hw 2020-12-17 22:27:11 +01:00
adi-linux-64@b6e379910a track openwifi-hw 2020-12-17 22:27:11 +01:00
doc doc/README.md udpate 2021-04-06 10:06:49 +02:00
driver fix the bug when retry_limit_raw==0 in sdr.c (0 is the abnormal number encountered in the monitor mode. normally it should >= 1). the bug causes 15 times transmissions for a packet if no ack is received 2021-04-05 21:53:29 +02:00
kernel_boot Update build_zynqmp_boot_bin.sh 2021-02-03 15:46:02 +01:00
LICENSES Update AGPL-3.0-or-later.txt 2021-02-03 16:33:45 +01:00
openwifi-hw@f8eb553a71 track the updated openwifi-hw 2021-04-05 21:35:52 +02:00
user_space add libpcap-dev into the post_config.sh. it is needed by packet injection program compiling 2021-04-05 21:56:17 +02:00
.gitmodules track correct openwifi-hw 2020-06-12 11:15:34 +02:00
CONTRIBUTING.md Update CONTRIBUTING.md 2021-02-03 15:28:13 +01:00
LICENSE Add LICENSE file. Just for github to recognize 2021-02-03 16:32:32 +01:00
openwifi-arch.jpg update openwifi architecture to have more details 2020-08-18 10:13:37 +02:00
openwifi-arch.jpg.license Update openwifi-arch.jpg.license 2021-02-03 15:17:44 +01:00
README.md Update README.md 2021-04-06 18:04:47 +02:00

openwifi

openwifi: Linux mac80211 compatible full-stack IEEE802.11/Wi-Fi design based on SDR (Software Defined Radio).

This repository includes Linux driver and software. openwifi-hw repository has the FPGA design. It is YOUR RESPONSIBILITY to follow your LOCAL SPECTRUM REGULATION or use CABLE to avoid potential interference over the air.

[Quick start] [Project document] [Application notes] [Videos] [Papers] [maillist] [Cite openwifi project]

Openwifi code has dual licenses. AGPLv3 is the opensource license. For non-opensource license, please contact Filip.Louagie@UGent.be. Openwifi project also leverages some 3rd party modules. It is user's duty to check and follow licenses of those modules according to the purpose/usage. You can find an example explanation from Analog Devices for this compound license conditions. [How to contribute].

Features:

  • 802.11a/g/n [IEEE 802.11n (Wi-Fi 4)]
  • 20MHz bandwidth; 70 MHz to 6 GHz frequency range
  • Mode tested: Ad-hoc; Station; AP, Monitor
  • DCF (CSMA/CA) low MAC layer in FPGA (10us SIFS is achieved)
  • 802.11 packet injection and fuzzing
  • CSI (Channel State Information, freq offset, equalizer to computer) [CSI notes]
  • IQ capture (real-time AGC, RSSI, IQ sample to computer) [IQ notes][IQ notes for dual antenna]
  • Configurable channel access priority parameters:
    • duration of RTS/CTS, CTS-to-self
    • SIFS/DIFS/xIFS/slot-time/CW/etc
  • Time slicing based on MAC address (time gated/scheduled FPGA queues)
  • Easy to change bandwidth and frequency:
    • 2MHz for 802.11ah in sub-GHz
    • 10MHz for 802.11p/vehicle in 5.9GHz
  • 802.11ax under development

Performance (AP: openwifi at channel 44, client: TL-WDN4200 N900 USB Dongle):

  • AP --> client: 30.6Mbps(TCP), 38.8Mbps(UDP)
  • client --> AP: 17.0Mbps(TCP), 21.5Mbps(UDP)

Supported SDR platforms: (Check Porting guide for your new board if it isn't in the list)

board_name board combination status SD card img Vivado license
zc706_fmcs2 Xilinx ZC706 dev board + FMCOMMS2/3/4 Done 32bit img Need
zed_fmcs2 Xilinx zed board + FMCOMMS2/3/4 Done 32bit img NO need
adrv9364z7020 ADRV9364-Z7020 + ADRV1CRR-BOB Done 32bit img NO need
adrv9361z7035 ADRV9361-Z7035 + ADRV1CRR-BOB/FMC Done 32bit img Need
zc702_fmcs2 Xilinx ZC702 dev board + FMCOMMS2/3/4 Done 32bit img NO need
zcu102_fmcs2 Xilinx ZCU102 dev board + FMCOMMS2/3/4 Done 64bit img Need
zcu102_9371 Xilinx ZCU102 dev board + ADRV9371 Future Future Need
  • board_name is used to identify FPGA design in openwifi-hw/boards/
  • Don't have any boards? Or you like JTAG boot instead of SD card? Check our test bed w-iLab.t tutorial.

[Quick start] [Basic operations] [Update FPGA] [Update Driver] [Update sdrctl] [Easy Access and etc]

[Build openwifi Linux img from scratch] [Special note for 11b] [Porting guide] [Project document] [Application notes]

Quick start

  • Burn openwifi board specific img file (from the table) into a SD card ("Open With Disk Image Writer". Or "dd" command after unzip). The SD card has two partitions: BOOT and rootfs. You need to config the correct files in the BOOT partition according to the board you have by operation on your computer:

    • Copy files in openwifi/board_name to the base directory of BOOT partition.
    • Copy openwifi/zynqmp-common/Image (zcu102 board) or openwifi/zynq-common/uImage (other boards) to the base directory of BOOT partition
  • Connect two antennas to RXA/TXA ports. Config the board to SD card boot mode (check the board manual). Insert the SD card to the board. Power on.

  • Login to the board from your PC (PC Ethernet should have IP 192.168.10.1) with password openwifi.

    ssh root@192.168.10.122
    
  • On board, run openwifi AP and the on board webserver

    ~/openwifi/fosdem-11ag.sh
    
  • After you see the "openwifi" SSID on your device (Phone/Laptop/etc), connect it. Browser to 192.168.13.1 on your device, you should see the webpage hosted by the webserver on board.

    • Note 1: If your device doesn't support 5GHz (ch44), please change the hostapd-openwifi.conf on board and re-run fosdem.sh.
    • Note 2: After ~2 hours, the Viterbi decoder will halt (Xilinx Evaluation License). Just power cycle the board if it happens. (If output of "./sdrctl dev sdr0 get reg rx 20" is always the same, it means the decoder halts)
  • To give the Wi-Fii client internet access, configure routing/NAT on the PC:

    sudo sysctl -w net.ipv4.ip_forward=1
    sudo iptables -t nat -A POSTROUTING -o NICY -j MASQUERADE
    sudo ip route add 192.168.13.0/24 via 192.168.10.122 dev ethX
    

    ethX is the PC NIC name connecting the board ethernet. NICY is the PC NIC name connecting internet (WiFi or another ethernet).

    If you want, uncommenting "net.ipv4.ip_forward=1" in /etc/sysctl.conf to make IP forwarding persistent on PC.

  • To monitor real-time CSI (Chip State Information), such as timestamp, frequency offset, channel state, equalizer, please refer to [CSI notes].

Basic operations

The board actually is an Linux/Ubuntu computer which is running hostapd to offer Wi-Fi AP functionality over the Wi-Fi Network Interface (NIC). The NIC is implemented by openwifi-hw FPGA design. We use the term "On board" to indicate that the commands should be executed after ssh login to the board. "On PC" means the commands should run on PC.

  • Bring up the openwifi NIC sdr0:
    service network-manager stop
    cd ~/openwifi && ./wgd.sh
    
  • Use openwifi as client to connect other AP (Change wpa-connect.conf on board firstly):
    route del default gw 192.168.10.1
    wpa_supplicant -i sdr0 -c wpa-connect.conf &
    dhclient sdr0
    
  • Use openwifi in ad-hoc mode: Please check sdr-ad-hoc-up.sh and sdr-ad-hoc-join.sh.
  • Use openwifi in monitor mode: Please check monitor_ch.sh.
  • The Linux native Wi-Fi tools/Apps (iwconfig/ifconfig/iwlist/iw/hostapd/wpa_supplicant/etc) can run over openwifi NIC in the same way as commercial Wi-Fi chip.
  • sdrctl is a dedicated tool to access openwifi driver/FPGA, please check doc directory for more information.

Update FPGA

Since the pre-built SD card image might not have the latest bug-fixes/updates, it is recommended to update the fpga bitstream on board.

  • Install Vivado/SDK 2018.3 (If you don't need to generate new FPGA bitstream, WebPack version without license is enough)
  • Setup environment variables (use absolute path):
    export XILINX_DIR=your_Xilinx_directory
    export OPENWIFI_DIR=your_openwifi_directory
    export BOARD_NAME=your_board_name
    
  • Get the latest FPGA bitstream from openwifi-hw, generate BOOT.BIN and transfer it on board via ssh channel:
    $OPENWIFI_DIR/user_space/get_fpga.sh $OPENWIFI_DIR
    
    For Zynq 7000:
    $OPENWIFI_DIR/user_space/boot_bin_gen.sh $OPENWIFI_DIR $XILINX_DIR $BOARD_NAME
    
    For Zynq MPSoC (like zcu102 board):
    $OPENWIFI_DIR/user_space/boot_bin_gen_zynqmp.sh $OPENWIFI_DIR $XILINX_DIR $BOARD_NAME
    
    scp $OPENWIFI_DIR/kernel_boot/boards/$BOARD_NAME/output_boot_bin/BOOT.BIN root@192.168.10.122:
    
  • On board: Put the BOOT.BIN into the BOOT partition.
    mount /dev/mmcblk0p1 /mnt
    cp ~/BOOT.BIN /mnt
    umount /mnt
    
    Power cycle the board to load new FPGA bitstream.

Update Driver

Since the pre-built SD card image might not have the latest bug-fixes/updates, it is recommended to update the driver on board.

  • Prepare Analog Devices Linux kernel source code (only need to run once):
    $OPENWIFI_DIR/user_space/prepare_kernel.sh $OPENWIFI_DIR $XILINX_DIR ARCH_BIT
    (For Zynq 7000, ARCH_BIT should be 32, for Zynq MPSoC, ARCH_BIT should be 64)
    
  • Compile the latest openwifi driver
    $OPENWIFI_DIR/driver/make_all.sh $OPENWIFI_DIR $XILINX_DIR ARCH_BIT
    (For Zynq 7000, ARCH_BIT should be 32, for Zynq MPSoC, ARCH_BIT should be 64)
    
  • Copy the driver files to the board via ssh channel
    scp `find $OPENWIFI_DIR/driver/ -name \*.ko` root@192.168.10.122:openwifi/
    
    Now you can use wgd.sh on board to load the new openwifi driver.

Update sdrctl

  • Copy the sdrctl source files to the board via ssh channel
    scp `find $OPENWIFI_DIR/user_space/sdrctl_src/ -name \*` root@192.168.10.122:openwifi/sdrctl_src/
    
  • Compile the sdrctl on board:
    cd ~/openwifi/sdrctl_src/ && make && cp sdrctl ../ && cd ..
    

Easy Access and etc

  • FPGA and driver on board update scripts
    • Setup ftp server on PC, allow anonymous and change ftp root directory to $OPENWIFI_DIR.
    • On board:
    ./sdcard_boot_update.sh $BOARD_NAME
    (Above command downloads uImage, BOOT.BIN and devicetree.dtb, then copy them into boot partition. Remember to power cycle)
    ./wgd.sh remote
    (Above command downloads driver files, and brings up sdr0)
    
  • Access the board disk/rootfs like a disk:
    • On PC: "File manager --> Connect to Server...", input: sftp://root@192.168.10.122/root
    • Input password "openwifi"

Build openwifi Linux img from scratch

  • Download 2019_R1-2020_02_04.img.xz from Analog Devices Wiki. Burn it to a SD card.

  • Insert the SD card to your Linux PC. Find out the mount point (that has two sub directories BOOT and rootfs), and setup environment variables (use absolute path):

    export SDCARD_DIR=sdcard_mount_point
    export XILINX_DIR=your_Xilinx_directory
    export OPENWIFI_DIR=your_openwifi_directory
    export BOARD_NAME=your_board_name
    
  • Run script to update SD card:

    $OPENWIFI_DIR/user_space/update_sdcard.sh $OPENWIFI_DIR $XILINX_DIR $BOARD_NAME $SDCARD_DIR
    
  • Config your board to SD card boot mode (check the board manual). Insert the SD card to the board. Power on.

  • Login to the board from your PC (PC Ethernet should have IP 192.168.10.1) with one time password analog.

    ssh root@192.168.10.122
    
  • Setup routing/NAT on the PC for your board -- this internet connection is important for post installation/config.

    sudo sysctl -w net.ipv4.ip_forward=1
    sudo iptables -t nat -A POSTROUTING -o NICY -j MASQUERADE
    sudo ip route add 192.168.13.0/24 via 192.168.10.122 dev ethX
    

    ethX is the PC NIC name connecting the board ethernet. NICY is the PC NIC name connecting internet (WiFi or another ethernet).

    If you want, uncommenting "net.ipv4.ip_forward=1" in /etc/sysctl.conf to make IP forwarding persistent on PC.

  • Run one time script on board to complete post installation/config (After this, password becomes openwifi)

    cd ~/openwifi && ./post_config.sh
    
  • Now you can start from Quick start (Skip the image download and burn step)

Special note for 11b

Openwifi only applies OFDM as its modulation scheme and as a result, it is not backward compatible with 802.11b clients or modes of operation. This is usually the case during beacon transmission, connection establishment, and robust communication.

As a solution to this problem, openwifi can be fully controlled only if communicating with APs/clients instantiated using hostapd/wpa_supplicant userspace programs respectively.

For hostapd program, 802.11b rates can be suppressed using configuration commands (i.e. supported_rates, basic_rates) and an example configuration file is provided (i.e. hostapd-openwifi.conf). One small caveat to this one comes from fullMAC Wi-Fi cards as they must implement the NL80211_TXRATE_LEGACY NetLink handler at the device driver level.

On the other hand, the wpa_supplicant program on the client side (commercial Wi-Fi dongle/board) cannot suppress 802.11b rates out of the box in 2.4GHz band, so there will be an issue when connecting openwifi (OFDM only). A patched wpa_supplicant should be used at the client side.

sudo apt-get install libssl1.0-dev
$OPENWIFI_DIR/user_space/build_wpa_supplicant_wo11b.sh $OPENWIFI_DIR

Porting guide

This section explains the porting work by showing the differences between openwifi and Analog Devices reference design. openwifi is based on 2019_R1 of HDL Reference Designs.

  • Open the fmcomms2 + zc706 reference design at hdl/projects/fmcomms2/zc706 (Please read Analog Devices help)
  • Open the openwifi design zc706_fmcs2 at openwifi-hw/boards/zc706_fmcs2 (Please read openwifi-hw repository)
  • "Open Block Design", you will see the differences between openwifi and the reference design. Both in "diagram" and in "Address Editor".
  • The address/interrupts of FPGA blocks hooked to the ARM bus should be put/aligned to the devicetree file openwifi/kernel_boot/boards/zc706_fmcs2/devicetree.dts. Linux will parse the devicetree.dtb when booting to know information of attached device (FPGA blocks in our case).
  • We use dtc command to get devicetree.dts converted from devicetree.dtb in Analog Devices Linux image, then do modification according to what we have added/modified to the reference design.
  • Please learn the script in [Build openwifi Linux img from scratch] to understand how we generate devicetree.dtb, BOOT.BIN and Linux kernel uImage and put them together to build the full SD card image.

Videos

Papers

Openwifi was born in ORCA project (EU's Horizon2020 programme under agreement number 732174).

Cite openwifi project

Any use of openwifi project which results in a publication should include a citation via (bibtex example):

@electronic{openwifigithub,
            author = {Xianjun, Jiao and Wei, Liu and Michael, Mehari},
            title = {open-source IEEE802.11/Wi-Fi baseband chip/FPGA design},
            url = {https://github.com/open-sdr/openwifi},
            year = {2019},
}

License

This project is available as open source under the terms of the AGPL 3.0 Or later. However, some elements are being licensed under GPL 2-0 or later and BSD 3 license . For accurate information, please check individual files.