k3ng_rotator_controller/rotator_pins.h

/* -------------------------------------   Pin Definitions ------------------------------------------ 

  You need to look at these and set them appropriately !

  Most pins can be disabled by setting them to 0 (zero).  If you're not using a pin or function, set it to 0.

  Pins > 99 = remote unit pin, for example: pin 109 = pin 9 on remote unit, pin A0+100 = pin A0 on remote unit

*/

/* azimuth pins --------------------- (use just the azimuth pins for an azimuth-only rotator) */

#define rotate_cw 6              // goes high to activate rotator R (CW) rotation - pin 1 on Yaesu connector
#define rotate_ccw 7             // goes high to activate rotator L (CCW) rotation - pin 2 on Yaesu connector
#define rotate_cw_ccw  0         // goes high for both CW and CCW rotation
#define rotate_cw_pwm 0          // optional - PWM CW output - set to 0 to disable (must be PWM capable pin)
#define rotate_ccw_pwm 0         // optional - PWM CCW output - set to 0 to disable (must be PWM capable pin)
#define rotate_cw_ccw_pwm 0      // optional - PWM on CW and CCW output - set to 0 to disable (must be PWM capable pin)
#define rotate_cw_freq 0         // optional - CW variable frequency output
#define rotate_ccw_freq 0        // optional - CCW variable frequency output
#define button_cw 0              // normally open button to ground for manual CW rotation (schematic pin: A1)
#define button_ccw 0             // normally open button to ground for manual CCW rotation (schematic pin: A2)
#define serial_led 0             // LED blinks when command is received on serial port (set to 0 to disable)
#define rotator_analog_az A0     // reads analog azimuth voltage from rotator - pin 4 on Yaesu connector
#define azimuth_speed_voltage 0  // optional - PWM output for speed control voltage feed into rotator (on continually unlike rotate_cw_pwm and rotate_ccw_pwm)
#define overlap_led 0            // line goes high when azimuth rotator is in overlap (> 360 rotators)
#define brake_az 0               // goes high to disengage azimuth brake (set to 0 to disable)
#define az_speed_pot 0           // connect to wiper of 1K to 10K potentiometer for speed control (set to 0 to disable)
#define az_preset_pot 0          // connect to wiper of 1K to 10K potentiometer for preset control (set to 0 to disable)
#define preset_start_button 0    // connect to momentary switch (ground on button press) for preset start (set to 0 to disable or for preset automatic start)
#define button_stop 0            // connect to momentary switch (ground on button press) for preset stop (set to 0 to disable or for preset automatic start)
#define rotation_indication_pin 0
#define blink_led 0
#define az_stepper_motor_pulse 44 //0



/*----------- elevation pins --------------*/
#ifdef FEATURE_ELEVATION_CONTROL
  #define rotate_up 8               // goes high to activate rotator elevation up
  #define rotate_down 9             // goes high to activate rotator elevation down
  #define rotate_up_or_down 0       // goes high when elevation up or down is activated
  #define rotate_up_pwm 0           // optional - PWM UP output - set to 0 to disable (must be PWM capable pin)
  #define rotate_down_pwm 0         // optional - PWM DOWN output - set to 0 to disable (must be PWM capable pin)
  #define rotate_up_down_pwm 0      // optional - PWM on both UP and DOWN (must be PWM capable pin)
  #define rotate_up_freq 0          // optional - UP variable frequency output
  #define rotate_down_freq 0        // optional - UP variable frequency output
  #define rotator_analog_el A1      // reads analog elevation voltage from rotator
  #define button_up 0               // normally open button to ground for manual up elevation
  #define button_down 0             // normally open button to ground for manual down rotation
  #define brake_el 0                // goes high to disengage elevation brake (set to 0 to disable)
  #define elevation_speed_voltage  0 // optional - PWM output for speed control voltage feed into rotator (on continually unlike rotate_up_pwm and rotate_down_pwm)
  #define el_stepper_motor_pulse 0
#endif //FEATURE_ELEVATION_CONTROL

// rotary encoder pins and options
#ifdef FEATURE_AZ_PRESET_ENCODER 
  #define az_rotary_preset_pin1 0                     // CW Encoder Pin
  #define az_rotary_preset_pin2 0                     // CCW Encoder Pin
#endif //FEATURE_AZ_PRESET_ENCODER

#ifdef FEATURE_EL_PRESET_ENCODER 
  #define el_rotary_preset_pin1 0                     // UP Encoder Pin
  #define el_rotary_preset_pin2 0                     // DOWN Encoder Pin
#endif //FEATURE_EL_PRESET_ENCODER

#ifdef FEATURE_AZ_POSITION_ROTARY_ENCODER
  #define az_rotary_position_pin1 0                     // CW Encoder Pin
  #define az_rotary_position_pin2 0                     // CCW Encoder Pin
#endif //FEATURE_AZ_POSITION_ROTARY_ENCODER

#ifdef FEATURE_EL_POSITION_ROTARY_ENCODER
  #define el_rotary_position_pin1 0                     // CW Encoder Pin
  #define el_rotary_position_pin2 0                     // CCW Encoder Pin
#endif //FEATURE_EL_POSITION_ROTARY_ENCODER

#ifdef FEATURE_AZ_POSITION_PULSE_INPUT
  #define az_position_pulse_pin 0                       // must be an interrupt capable pin!
  #define AZ_POSITION_PULSE_PIN_INTERRUPT 0             // Uno: pin 2 = interrupt 0, pin 3 = interrupt 1 ; Mega: pin 2 = interrupt 0, pin 3 = interrupt 1, pin 21 = interrupt 2, pin 20 = interrupt 3, pin 19 = interrupt 4, pin 18 = interrupt 5
#endif                                                // read http://arduino.cc/en/Reference/AttachInterrupt for details on hardware and interrupts

#ifdef FEATURE_EL_POSITION_PULSE_INPUT
  #define el_position_pulse_pin 1                       // must be an interrupt capable pin!
  #define EL_POSITION_PULSE_PIN_INTERRUPT 1             // Uno: pin 2 = interrupt 0, pin 3 = interrupt 1 ; Mega: pin 2 = interrupt 0, pin 3 = interrupt 1, pin 21 = interrupt 2, pin 20 = interrupt 3, pin 19 = interrupt 4, pin 18 = interrupt 5
#endif                                                // read http://arduino.cc/en/Reference/AttachInterrupt for details on hardware and interrupts

#ifdef FEATURE_PARK
  #define button_park 0
#endif

//classic 4 bit LCD pins
#define lcd_4_bit_rs_pin 12
#define lcd_4_bit_enable_pin 11
#define lcd_4_bit_d4_pin 5
#define lcd_4_bit_d5_pin 4
#define lcd_4_bit_d6_pin 3
#define lcd_4_bit_d7_pin 2


#ifdef FEATURE_JOYSTICK_CONTROL
  #define pin_joystick_x A0
  #define pin_joystick_y A1
#endif //FEATURE_JOYSTICK_CONTROL

#ifdef FEATURE_AZ_POSITION_HH12_AS5045_SSI
  #define az_hh12_clock_pin 11
  #define az_hh12_cs_pin 12
  #define az_hh12_data_pin 13
#endif //FEATURE_AZ_POSITION_HH_12

#ifdef FEATURE_EL_POSITION_HH12_AS5045_SSI
  #define el_hh12_clock_pin 53 //11
  #define el_hh12_cs_pin 52 //12
  #define el_hh12_data_pin 51 //13
#endif //FEATURE_EL_POSITION_HH_12

#ifdef FEATURE_PARK
  #define park_in_progress_pin 0  // goes high when a park has been initiated and rotation is in progress
  #define parked_pin 0            // goes high when in a parked position
#endif //FEATURE_PARK

#define heading_reading_inhibit_pin 0 // input - a high will cause the controller to suspend taking azimuth (and elevation) readings; use when RF interferes with sensors

#ifdef FEATURE_LIMIT_SENSE
  #define az_limit_sense_pin 0  // input - low stops azimuthal rotation
  #define el_limit_sense_pin 0  // input - low stops elevation rotation
#endif //FEATURE_LIMIT_SENSE

#ifdef FEATURE_AZ_POSITION_INCREMENTAL_ENCODER
  #define az_incremental_encoder_pin_phase_a 18 //3 must be an interrupt capable pin
  #define az_incremental_encoder_pin_phase_b 19 //3 // must be an interrupt capable pin
  #define az_incremental_encoder_pin_phase_z 22 //4
  #define AZ_POSITION_INCREMENTAL_ENCODER_A_PIN_INTERRUPT 5 //0             // Uno: pin 2 = interrupt 0, pin 3 = interrupt 1 ; Mega: pin 2 = interrupt 0, pin 3 = interrupt 1, pin 21 = interrupt 2, pin 20 = interrupt 3, pin 19 = interrupt 4, pin 18 = interrupt 5
  #define AZ_POSITION_INCREMENTAL_ENCODER_B_PIN_INTERRUPT 4 //1             // Uno: pin 2 = interrupt 0, pin 3 = interrupt 1 ; Mega: pin 2 = interrupt 0, pin 3 = interrupt 1, pin 21 = interrupt 2, pin 20 = interrupt 3, pin 19 = interrupt 4, pin 18 = interrupt 5
                                                                              // read http://arduino.cc/en/Reference/AttachInterrupt for details on hardware and interrupts
#endif //FEATURE_AZ_POSITION_INCREMENTAL_ENCODER

#ifdef FEATURE_EL_POSITION_INCREMENTAL_ENCODER
  #define el_incremental_encoder_pin_phase_a 2 //18 //2 // must be an interrupt capable pin
  #define el_incremental_encoder_pin_phase_b 3 //19 //3 // must be an interrupt capable pin
  #define el_incremental_encoder_pin_phase_z 5 //22 //4
  #define EL_POSITION_INCREMENTAL_ENCODER_A_PIN_INTERRUPT 0 //5 //0             // Uno: pin 2 = interrupt 0, pin 3 = interrupt 1 ; Mega: pin 2 = interrupt 0, pin 3 = interrupt 1, pin 21 = interrupt 2, pin 20 = interrupt 3, pin 19 = interrupt 4, pin 18 = interrupt 5
  #define EL_POSITION_INCREMENTAL_ENCODER_B_PIN_INTERRUPT 1 //4 //1             // Uno: pin 2 = interrupt 0, pin 3 = interrupt 1 ; Mega: pin 2 = interrupt 0, pin 3 = interrupt 1, pin 21 = interrupt 2, pin 20 = interrupt 3, pin 19 = interrupt 4, pin 18 = interrupt 5
                                                                              // read http://arduino.cc/en/Reference/AttachInterrupt for details on hardware and interrupts
#endif //FEATURE_EL_POSITION_INCREMENTAL_ENCODER

#ifdef FEATURE_YOURDUINO_I2C_LCD
  #define En_pin  2
  #define Rw_pin  1
  #define Rs_pin  0
  #define D4_pin  4
  #define D5_pin  5
  #define D6_pin  6
  #define D7_pin  7
#endif //FEATURE_YOURDUINO_I2C_LCD

#ifdef FEATURE_MOON_TRACKING
  #define moon_tracking_active_pin 0    // goes high when moon tracking is active
  #define moon_tracking_activate_line 0 // ground this pin to activate moon tracking (not for use with a button)
  #define moon_tracking_button 0        // use with a normally open momentary switch to ground
#endif //FEATURE_MOON_TRACKING

#ifdef FEATURE_SUN_TRACKING
  #define sun_tracking_active_pin 0    // goes high when sun tracking is active
  #define sun_tracking_activate_line 0 // ground this pin to activate sun tracking (not for use with a button)
  #define sun_tracking_button 0      // use with a normally open momentary switch to ground
#endif //FEATURE_SUN_TRACKING

#ifdef FEATURE_GPS
  #define gps_sync 0
#endif //FEATURE_GPS

#ifdef FEATURE_POWER_SWITCH
  #define power_switch 0             // use with FEATURE_POWER_SWITCH
#endif //FEATURE_POWER_SWITCH

#ifdef FEATURE_EL_POSITION_MEMSIC_2125
  #define pin_memsic_2125_x 0
  #define pin_memsic_2125_y 0
#endif //FEATURE_EL_POSITION_MEMSIC_2125

#ifdef FEATURE_ANALOG_OUTPUT_PINS
  #define pin_analog_az_out 0
  #define pin_analog_el_out 0
#endif //FEATURE_ANALOG_OUTPUT_PINS

#ifdef FEATURE_SUN_PUSHBUTTON_AZ_EL_CALIBRATION
  #define pin_sun_pushbutton_calibration 0             // normally HIGH, have button pull LOW
#endif //FEATURE_SUN_PUSHBUTTON_AZ_EL_CALIBRATION

#ifdef FEATURE_MOON_PUSHBUTTON_AZ_EL_CALIBRATION
  #define pin_moon_pushbutton_calibration 0            // normally HIGH, have button pull LOW
#endif //FEATURE_MOON_PUSHBUTTON_AZ_EL_CALIBRATION

//#define reset_pin 22 // if defined, goes HIGH to reset unit

#if defined(FEATURE_AZ_POSITION_A2_ABSOLUTE_ENCODER) || defined(FEATURE_EL_POSITION_A2_ABSOLUTE_ENCODER)
  #define pin_sei_bus_busy 24
  #define pin_sei_bus_send_receive 22  
#endif

#ifdef FEATURE_YWROBOT_I2C_DISPLAY
  #define ywrobot_address 0x3F
  #define ywrobot_pin_en 2
  #define ywrobot_pin_rw 1
  #define ywrobot_pin_rs 0
  #define ywrobot_pin_d4 4
  #define ywrobot_pin_d5 5
  #define ywrobot_pin_d6 6
  #define ywrobot_pin_d7 7
  #define ywrobot_pin_bl 3
  #define ywrobot_blpol POSITIVE             
#endif //FEATURE_YWROBOT_I2C_DISPLAY