Some configs specify kernel/initrd paths relative to a device (often
found in a variable). Assume the device is the /boot partition and
ignore the device specification.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Extract exclusion for unpartitioned block device of partitioned media
to gui_functions, and exclude them even if kernel hasn't listed the
partitions yet. (Fixes flash/USB boot prompts incorrectly trying to
use the whole device for partitioned media the first time.)
Ignore block devices of size 0, like empty USB SD card readers.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
- Have Talos II supported by detecting correctly size of mtd chip (not internal: different flashrom output needs to be parsed for chip size)
- Read SPI content only once: 66% speedup (TOCTOU? Don't think so, nothing should happen in parallel when flashing insingle user mode)
- Have the main flash_progress loop not break, but break in flash_rom state subcases (otherwise, verifying step was breaking)
- Change "Initializing internal Flash Programmer" -> "Initializing Flash Programmer"
- Apply changes suggested by @SergiiDmytruk under https://github.com/osresearch/heads/pull/1230#issuecomment-1295332539 to reduce userland wasted time processing flashrom -V output
patches/coreboot-4.15: remove patches for coreboot 4.15
No boards depend on it and is affected by CVE-2022-29264
Signed-off-by: Daniel Pineda <daniel.pineda@puri.sm>
Add patches for coreboot 4.17:
- show ME status even when device is disable (kept from 4.15)
- zero unused part of SMBIOS region
Signed-off-by: Daniel Pineda <daniel.pineda@puri.sm>
It specifies whitespace-separated list of console devices to run Heads
on in addition to the default one.
Example for board config:
export CONFIG_BOOT_EXTRA_TTYS="tty0 tty1"
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
This also involves splitting workspaces based on target architecture to
avoid severely degrading performance of CI.
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
To be used in board configuration. Expands to the path of the board's
build directory. Also simplifies main Makefile a bit.
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
This makes configs much less dependent on directory layout.
As of this commit the following variables are supported:
* @BOARD_BUILD_DIR@ - absolute path under build/
* @BLOB_DIR@ - absolute path to blobs/
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Enable virtio video and storage.
Enable serial console and tweak kernel command line to show logs.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Add qemu-coreboot-fbwhiptail-tpm1-hotp configuration, which has a 'run'
target to boot with a persistent TPM, disk, virtual USB disk, and USB-
forwarded token
Provide instructions for bootstrapping a complete working system in qemu
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
flashrom doesn't work in qemu, so the firmware isn't able to update its
keyring. Adding an already-provisioned key ahead of time works though.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Set ATA and SATA configs to y, not m - modules weren't being loaded. Other
configs also build these into kernel, so do the same for qemu. Remove relevant
configs from boards since modules no longer need to be in initrd.
Enable OHCI and UHCI. qemu forwards host USB devices over a UHCI controller.
This enables USB-forwarding a physical Librem Key or Nitrokey Pro to the VM.
Export CONFIG_LINUX_USB_COMPANION_CONTROLLER to have enable_usb() load the
modules - it wants both UHCI and OHCI modules, so build both.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Otherwise binary patches cannot be patched/created
Additional fixes needed
- flashrom patch was invalid and got catched by git apply. Correcting
- gpg2-2.2.21.patch was pointing to bad target. Correcting
