gui-init: make sure that reseal_tpm_disk_decryption_key happens only on successful TOTP/HOTP sealing, reusing cached TPM Owner password
Signed-off-by: Thierry Laurion <insurgo@riseup.net>
We just set the TPM owner password, so there's no need to make the user
enter it again. Eliminates some failure modes if the user mistypes it
or enters the wrong password.
Allow optionally passing in the TPM owner password in tpmr seal,
check_tpm_counter(), seal-totp, and generate_totp_htop(). The user is
still prompted if the password is needed but was not provided, so
existing uses in other contexts continue to work unchanged.
Prompt for the password in reset_tpm() and pass it down to each of the
above.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
gui-init: do not consume two unseal attempt to unseal both totp and hotp + cosmetic changes (slow down TPM DA lockout)
kexec-seal-key: Add DEBUG statement for PCR precalc
seal-totp: add DEBUG statements regarding skipping of PCR5 and PCR6 involvement into TOTP/HOTP sealing ops
seal-hotpkey: Add DEBUG statements related to reuse of TOTP sealed secret
tpmr: add DO_WITH_DEBUG calls to output pcrread and extend calls
tpmr: typo correction stating TRACE calls for tpm2 where it was for tpm1
tpmr: add DO_WITH_DEBUG calls for calcfuturepcr
functions: Cosmetic fix on pause_recovery asking user to press Enter to go to recovery shell on host console when board defines CONFIG_BOOT_RECOVERY_SERIAL
Not so related but part of output review and corrections:
kexec-insert-key: cosmetic changes prepending "+++" to disk related changes
kexec-save-default: cosmetic changes prepending "+++" to disk related changes
config/coreboot-qemu-tpm*.config: add ccache support for faster coreboot rebuild times
Provide tpmr commands pcrread, pcrsize, calcfuturepcr, and seal for
both TPM1 and TPM2.
Combine seal logic for TPM1/TPM2 in seal-totp, kexec-seal-key. This is
essentially the TPM2 logic now that tpmr provides the same wrapped
commands for both TPM1 and TPM2.
Remove algorithm prefix from PCR list in tpmr unseal for consistency
with tpmr seal.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
Most logic throughout Heads doesn't need to know TPM1 versus TPM2 (and
shouldn't, the differences should be localized). Some checks were
incorrect and are fixed by this change. Most checks are now unchanged
relative to master.
There are not that many places outside of tpmr that need to
differentiate TPM1 and TPM2. Some of those are duplicate code that
should be consolidated (seal-hotpkey, unseal-totp, unseal-hotp), and
some more are probably good candidates for abstracting in tpmr so the
business logic doesn't have to know TPM1 vs. TPM2.
Previously, CONFIG_TPM could be variously 'y', 'n', or empty. Now it
is always 'y' or 'n', and 'y' means "any TPM". Board configs are
unchanged, setting CONFIG_TPM2_TOOLS=y implies CONFIG_TPM=y so this
doesn't have to be duplicated and can't be mistakenly mismatched.
There were a few checks for CONFIG_TPM = n that only coincidentally
worked for TPM2 because CONFIG_TPM was empty (not 'n'). This test is
now OK, but the checks were also cleaned up to '!= "y"' for robustness.
Signed-off-by: Jonathon Hall <jonathon.hall@puri.sm>
-coreboot support of TPM v2.0 (shared config for TPM2 support across all 4 previous variations)
-swtpm set to be launched under TPM v2.0 mode under board config
-Documentation file under each board.md softlinks to qemu-coreboot-fbwhiptail-tpm1.md (which has been generalized)
This is skeleton for TPM v2 integration under Heads
-------------
WiP
TODO:
- libcurl cannot be built as a tpm2-tools dependency as of now not sure why. curl currently needs to be added in board config to be built
- Note: tpm-reset (master and here) needs some review, no handle of no tpm use case. Caller is responsible to not call it otherwise does nothing
- init tries to bind fd and fails currently
- Note: Check if whiptail is different of fbwhiptail in clearing screen. As of now every clear seems to be removed, still whiptail clears previous console output
- When no OS' /boot can be mounted, do not try to TPM reset (will fail)
- seal-hotpkey is not working properly
- setting disk unlock key asks for TPM ownership passphrase (sealing in NV requires ownership, but text is misleading user as if reowning TPM)
- We should cache input, feed tpm behind the scene and wipe passphrase and state clearly that this is TPM disk unlock kye passphrase.
- primary key from TPM2 is invalid most of the time from kexec-select-boot and verifying global hashes but is setuped correctly at disk unlock key setup
- would be nice to take advantage of bash function tracing to understand where we are for debugging purposes, code takes ash in consideration only
- tpmr says it implements nv calls but actually doesn't. Removing those falsely wrapped functions would help.
- Implementing them would be better
- REVIEW TODOS IN CODE
- READD CIRCLECI CONFIG
Current state:
- TPM unseal works without disk unlock key and generates TOTP properly (was missing die condition at unseal to not produce always good TOTP even if invalid)
- TPM disk encryption key fails. Hypothesis is that sealing with USB drivers loaded and measures in inconsistent with sealed with/without.
- TPM disk unsealing happens without USB modules being loaded in non-HOTP setup. This fails.
- Current tests are with fbwhiptail (no clear called so having traces on command line of what happens)
- Testing with HOTP implementation for sealing/unsealing since that forces USB module loads on each boot to remove this from failing possibilities
- Add TRACE function tracing output under etc/functions, depending on CONFIG_ENABLE_FUNCTION_TRACING_OUTPUT enabled in board configs
- Replace current DEBUG to TRACE calls in code, reserving DEBUG calls for more verbose debugging later on (output of variables etc)
- add 'export CONFIG_ENABLE_FUNCTION_TRACING_OUTPUT=y' in qemu-coreboot(fb)whiptail-tpm1(-hotp) boards to see it in action
