This patch addresses corner cases not considered so far. In particular,
it avoids placing the Add/Options tabs of an unscrollable popup under
the panel. This could happen in the presence of many options. The patch
includes the panel height into the calculation to rule out such
situations. It also tightens the scrolling boundaries to the visible
content.
Issue #5183
This patch handles intermediate situations where the screen mode may
become 1 x 1 (absence of any capture clients). In this case, the
decoration of a maximized window would legitimately exceed the screen
boundary.
Thanks Johannes for the investigation.
Issue #5187
Issue #5180
The blanking state is evaluated by the intel_fb driver, which will switch
off all connectors. When done, the intel_fb driver will exit and the
sculpt_manager will continue with the next step, stopping all drivers.
Issue #5180
This commit adds missing routes to I2c for the framebuffer driver of the
MNT Reform. If build for this concrete board the Board_info::Soc variable
within the sculpt_manager is initialized according to the properties of
this device. The `update_soc` routine is called in the initialization of
the sculpt_manager, otherwise it won't be called at all, if no PCI devices
changes are detected. Missing driver binaries and device-tree-binaries are
add to the run-script.
Issue #5174
A network card can be provided by PCI, and the SoC as well. Therefore,
add an additional state variable in the Board_info::Soc, and check it
appropriatedly.
Issue #5174
Commit "sculpt: safeguard the offering of suspend/resume" was too lax
about the detection of acpi support. In situations where acpi support
is selected but not yet installed, the menu would offer the features
already. This patch restricts the condition such that acpi support must
be running, not merely selected.
Issue #5174
This patch retains the buffer size of the last capture client as mode as
long as no capture client exists. This avoids intermediate mode changes
in situations like suspend/resume where the display driver is restarted.
Issue #5187
In contrast to platforms, like the PC, where the fb driver selection
is a dynamic decision depending on the available hardware, on current
ARM-based SoC machines this configuration is part of the static board
information.
Issue #5174.
This patch disables latency warnings by default. The warnings can be
enabled by setting the 'warning_rate_ms` value to the desired
maximum rate.
Fixes#5186
Issue #5174
The USB host controller gets restarted during the suspend-resume cycle.
Hence, don't offer suspend while any USB storage device is in use, in
particular when deploying Sculpt from a USB stick.
Suspend/resume is not supposed to work with any framebuffer driver other
than intel_fb. Therefore, offer the suspend feature only when using intel_fb.
Issue #5174
The automatic restart of intel_fb got lost during the transition from
the driver manager. This commit restores the heartbeat monitoring of
this driver.
Issue #5174
This patch enhances the sculpt manager to drive the system state
and manage the lifecycle of driver components during suspend-
resume cycles.
The new Power options can be found in the System menu. The suspend
and power-off controls are presented only when the acpi-support
option is activated.
Note that the USB controller is hard restarted when resuming from
suspend. Hence, all components that depend on USB are restarted
implicitely.
Issue #5180
Issue #5174
on display client close (intel_fb). The former code constructed a
temporary object on the stack, which sets up the scratch pages for the
closed client. However, the scratch page backing store (dma_buffer) gets
freed on destruction of the temporary stack object, which leads to DMA faults
with visual noise on the screen. Instead, use the already in use ggtt object
and add the scratch pages explicitly.
Issue #5180
This disambiguates the boot images installed for base-hw from those
installed for base-nova.
Note that the image.elf file for other kernels (i.e., NOVA) is not
named image-<kernel>.elf at this point because this would prevent the
update from a pre-24.04 Sculpt system to a later one as the grub.cfg
is not touched by the old update mechanism. So after a system update,
grub would keep loading the last installed image.elf.
Issue #5182
This commits updates the contrib sources to version 8.7.1.
This version requires more random entropy as it queries OpenSSL
about the current random state and will bail if it is not sufficient.
Doubling the content of the '<inline>' VFS plugin as used in static
configurations seems satisfactory.
Furthermore DNS resolving needs a configured '<pipe>' plugin to work
properly.
Fixes#5184.
Instead of returning an invalid capability whenever an interface is
requested that does not exist, create a disconnected interface component.
It is also possible that a client requests an interface that got removed
at the same time. When an invalid capability gets returned, a client
can stumble about invoking it.
Moreover, this commit marks either invalid interface or device components
as disconnected objects to optimize their handling.
Ref genodelabs/genode#5021
This is an intermediate solution for accommodating overly long
text lines that can appear in report/runtime/usb/devices in the
presence of long product strings.
Issue #5174
In the scheduler's implementation preserve the consumed slack-time
over periods of activation/deactivation, but instead of appending
activated jobs to the end of the slack queue, insert it as new head.
Thereby, the extreme discrimination of threads with short execution
times and frequent blocking behaviour against long running computations
gets avoided.
Fixgenodelabs/genode#4796
