* Add isr.s assembler file:
The file declares an array of Interrupt Service Routines (ISR) to handle
the exception vectors from 0 to 19, see Intel SDM Vol. 3A, section
6.3.1.
* Add Idt class:
* The class Genode::Idt represents an Interrupt Descriptor Table as
specified by Intel SDM Vol. 3A, section 6.10.
* The setup function initializes the IDT with 20 entries using the ISR
array defined in the isr.s assembly file.
* Setup and load IDT in Genode::Cpu ctor:
The Idt::setup function is only executed once on the BSP.
* Declare ISRs for interrupts 20-255
* Set IDT size to 256
The boot modules assembled by the generated boot_modules.s file is
accessed from core using struct Bm_header. Unfortunately the assembler
.long directive is synonym to .int [1] and thus has the same size as the
C++ int type and *not* long. Use the matching assembly type .quad in
boot_modules.s when generating the file for 64-bit platforms such as
x86_64.
[1] - https://sourceware.org/binutils/docs/as/Long.html
This patch contains the initial code needed to build and bootstrap the
base-hw kernel on x86 64-bit platforms. It gets stuck earlier
because the binary contains 64-bit instructions, but it is started in
32-bit mode. The initial setup of page tables and switch to long mode is
still missing from the crt0 code.
On each execution the output buffer is overriden when run_genode_until
is executed multiple times. Run scripts, that depend on extracting
information after several execution steps, e.g. noux_net_netcat, will
fail to do so. Therefore, we append the newly captured log output to
the old output buffer.
Issue #1327.
A Nic::Session client can install a signal handler that is used to
propagate changes of the link-state by calling 'link_state_sigh()'.
The actual link state is queried via 'link_state()'.
The nic-driver interface now provides a Driver_notification callback,
which is used to forward link-state changes from the driver to the
Nic::Session_component.
The following drivers now provide real link state: dde_ipxe, nic_bridge,
and usb_drv. Currently, OpenVPN, Linux nic_drv, and lan9118 do not
support link state and always report link up.
Fixes#1327
If a client acknowledges the same packet more than once, the packet also
gets freed more than once. At the second attempt the underlaying
Bit_array will throw an 'Invalid_clear' exception, which results in an
uncaught exception that leads to an abort() call in the freeing
component.
Fixes#1462.
To ease debugging without the need to tweak the kernel every time, and to
support userland developers with useful information this commit extends several
warnings and errors printed by the kernel/core by which thread/application
caused the problem, and what exactly failed.
Fix#1382Fix#1406
The driver for the Freescale eSDHCv2 doesn't support the highest
available bus frequency by now and also the bus width may be set to a
higher value but that needs further checks on the capabilities of the
inserted card.
The commits provide a benchmark as it exists for the OMAP4 SDHC driver.
Fix#1458
The 'continue_hw_accelerated' assertion at the end of the recall handler
can fail in situations which are not problematic, for example if the
'Timer' thread has set the 'VMCPU_FF_TIMER' flag in the meantime and
requested a recall afterwards. Since we don't know for sure if a recall is
requested for the other flags as well, the assertion gets replaced by a
debug message, which gets printed if any of the 'not yet verified as safe'
flags is set.
Fixes#1426
The GUID partition table (GPT) is primarily used by systems using
(U)EFI and is a replacement for the legacy MBR. For now, the current
implementation is able to address up to 128 GUID partition entries
(GPE).
To enable the GPT support in 'part_blk' it has to be configured
accrodingly:
! <start name="part_blk">
! [...]
! <config use_gpt="yes">
! [...]
! </start>
If 'part_blk' is not able to find a valid GPT header it falls back
to using the MBR.
Current limitations:
Since no endian conversion takes place it only works on LE platforms
and of all characters in the UTF-16 encoded name field of an entry
only the ones included in the ASCII encoding are printed. It also
ignores all GPE attributes.
Issue #1429.
The hover reports provides information about the session currently
pointed-to, i.e., hovered session. It can be enabled by the 'hover'
attribute of nitpicker's 'report' configuration element
<report hover="yes" />
Fixes#1442
The bindings for 32bit did not consider that in the syscall_3 function
edx changes due to the assembly instructions and that in the syscall_4
function edx and ecx change. So, the compiler wrongly assumed that the
content of these registers stayed unchanged.
Fixes#1447
