* The device XML information dataspace is only provided,
when the client's policy states `info="yes"`
* The device XM information gets changed to include the
physical resource names (I/O memory and IRQ addresses)
instead of virtual ids and page offset
Fix#4077
This API rework eases the access to memory-mapped I/O registers and
interrupts when using the platform driver. It introduces the notions of
- Platform::Device - one device obtained from a platform session
- Platform::Device::Mmio - locally-mapped MMIO registers of a device
- Platform::Device::Irq - interface for receiving device interrupts
The patch touches several drivers. Some drivers would require a
significant structural change to adopt the new API (e.g., net/virtio,
dde_linux drivers, imx gpio). In these cases, the patch adds
compatibility shims meant to be temporary. In other cases (e.g., imx
i2c), the adaptation was simple enough to carry through.
Fixes#4075
Note, OpenSSL now comes as one combined depot archive *openssl* that
replaces the former *libssl* and *libcrypto* archives. The libraries are
still separate binaries for compatibility with legacy software.
Issue #3773
In order to perform a smooth transition from NIC drivers that act only as NIC
session clients to NIC drivers that act only as Uplink session clients, this
commit introduces an intermediate state in which all NIC drivers support both
modes. That said, a NIC drivers mode is now statically determined through a new
optional 'mode' attribute in the drivers <config> tag that can be set to either
'nic_server' (default value) or 'uplink_client'. Reconfiguring this attribute
at a driver doesn't have any effects. Whithout this attribute being set, all
NIC drivers will behave the same as they did before the commit. When set to
'uplink_client', however, instead of providing a Nic service, they request
an Uplink session whenever their network interface becomes "UP" and close the
session whenever their network interface becomes "DOWN".
Ref #3961
By now, the enumeration of peripheral interrupts on Raspberry Pi 1 was
different in between base-hw kernel and Fiasco.OC. Therefore, hacks were
needed in every driver to request the correct interrupt number dependent
on the kernel. Before reproducing the same in the platform driver for rpi,
we can more easily use the same enumeration with base-hw.
Ref #3864
This commit applies the transition from the "Input" session to the "Event"
session to the event-filtering mechansim. The functionality of the
input_filter is now provided by the event_filter. The event filter
requests only one "Event" session as destination for the filter result,
which is usually routed to the nitpicker GUI server. It provides an
"Event" service to which any number of event sources can connect.
The configuration of the filter chain remains almost the same. Only the
declaration of the <input> nodes is no longer needed. Instead, the
configuration must specify <policy> nodes, which define the mapping of
"Event" clients (event sources) to the inputs used in the filter chain.
The patch adjusts all uses of the nitpicker GUI server accordingly such
that the event filter reports events to nitpicker's event service
instead of having nitpicker request an "Input" session. This dissolves
the dependency of nitpicker from input drivers.
Issue #3827
This patch replaces the use of the "Framebuffer" session interface by
the new "Capture" session interface in all framebuffer drivers. Thanks
to this change, those drivers have become mere clients of the nitpicker
GUI server now, and are no longer critical for the liveliness of the GUI
server.
The patch touches the following areas:
- The actual driver components. The new versions of all drivers have
been tested on the respective hardware. Generally, the drivers
have become simpler.
- The drivers_interactive packages for various boards. The drivers
subsystem no longer provides a "Framebuffer" service but needs a
valid route to the "Capture" service provided by nitpicker.
- The driver manager of Sculpt OS.
- This patch changes the role of the test-framebuffer component from a
framebuffer client to a capture server so that drivers (capture clients)
can be directly connected to the test component without the nitpicker
server.
- Framebuffer driver no longer support the unbuffered mode.
- The fb_bench.run script is no longer very meaningful because it
interplays solely with nitpicker, not with the driver directly.
- All run scripts for graphical scenarios and the related depot
archives got adapted to the change.
Fixes#3813
Until now, Genode's framebuffer session interface was based on the
RGB565 pixel format. This patch changes the pixel format to 32-bit
XRGB where the X part is ignored. It adapts all graphical applications
and device drivers accordingly.
The patch also adjusts the users of the drivers_interactive packages,
assigning 64 MiB RAM and 1500 caps to the drivers subsystem, which is
sufficient for covering high resolutions at 32 bits per pixel and to
accommodate multi-component USB HID input stacks.
Fixes#3784
