The new API emphasizes control over the vCPU data by granting access
through the Vcpu::with_state() method, which makes sure that the vCPU is
stopped, invokes the supplied function with a reference to the VM state
and resumes the vCPU if the function returns true.
The old Vcpu::run(), Vcpu::pause() and Vcpu::state() methods are removed
in favor of the new API. Execution of the vCPU is now interrupted by
sending a native Genode Signal to its Vcpu_handler, which will run the
VMM's exit handling method. When this method retrieves the vCPU state by
calling Vcpu::with_state(), the outside interruption is detected and on
x86 a recall exit is injected into the state to signal the vCPU
interruption / pause request to the VMM's vCPU handler.
Ref #4968
instead via the hardware registers of the FPU. On Genode all components and
so VMMs are built such, that the compiler may generate optimized code by
using the FPU at any time. We had to make sure to save the
FPU state as early as possible before the VMM component touches the FPU,
to avoid corrupting & losing guest FPU state. This caused headache again
and again. To avoid the uncertainty, we remove this feature and explicitly
transfer the FPU state via the UTCB.
Depending on the client and use-case the current minimal timeout
value of 5 ms could be too high, lowering it to 1 ms stays within
the limit imposed by most timer drivers.
Issue #4990.
When the wait value is too small the HALT attempt turnes into
busy-polling in the VMM. To prevent that always wait a minimal
amount of time.
Issue #4990.
This patch removes the obsolete 'io_progress_elem', which was wrongly
enqueued to the 'read_ready_waiters' fifo and not dequeued at
destruction time.
Fixes#4987
GNU Make 4.4 will pass TARGET to the sub-make of UNDEF_REFS where it can
be later used as link TARGET by Genode's build system. Before 4.4 TARGET
was undefined in the sub-make leading to the correct result.
Remove 'usb_hid', 'usb_net', 'usb_modem' from dde_linux port. These
versions have been updated to Linux 6.1.20 which uses the 'linux.port'
file.
issue #4958
The driver is superseded by the USB network driver (usb_net) which also
contains MBIM support for LTE modems previously provided by this
driver.
issue #4958
The drivers uses the 'virt_linux' api and the current lx_kit
implementation. It is a drop-in replacement for the Linux 4.16.3 based
version.
issue #4958
NCM tries to batch TX packets using timeouts (500us) and does not send packets
before 3 packets are in the submit queue. Timeouts take milliseconds on
dde_linux which leads to delayed ACKs and poor performance for the RX case.
Therefore, we send small packets (<100 Bytes) immediately without batching (it
might be an ACK or last packet of a larger transfer).
issue #4958
The PinePhone Modems' CDC Ethernet Interface does not respond if RX/TX queue size
is greater 12 (experimentally determined), the default would be 60, meaning 60
RX Bulk URBs are sent at once to the device.
issue #4958
A WRITE_ERR_WOULD_BLOCK may occur when large reports are written to a file
system because this fills up the submit queue of the packet-stream interface.
Fixesgenodelabs/genode#4988
This commits introduces changes to test number 4, so it must keep
more than one PKG. Also, it introduces a 5th test to verify that the
<remove_all/> functionality does delete everything in the depot.
Issue genodelabs#4866
This commits introduces improvements to the test functions to avoid
code duplication, and renames these functions to reflect better what they
are used for.
Issue genodelabs#4866
The last character should only be skipped if a `\0` or `\n` is found. If
the string ends without such a character or the maximum line length is
hit, we do not skip the last character.
Fixesgenodelabs/genode#4985
