If a component is being destroyed just before it calls `exit()` at its
parent, the `exit()` call causes an `Ipc_error` exception, which leads to
an `abort()` loop with repeated error messages, because `abort()` calls
`exit()` too. Catching the exception in `Expanding_parent_client::exit()`
avoids this problem.
Fixes#3228
bus or device should be different (not both) when comparing a device to
already present devices. Because of this the second USB device was
marked as existent when the bus matched or the bus did not but the
device number.
This patch gives applications the ability to control the size of their
window whenever the window is floating, not tiled or maximized. See the
comment in the code for the rationale.
Fixes#3200
The default rate of 100 ms keeps Sculpt too busy because the menu that
displays the percentage values is drawn completely on each update.
Limiting the rate to 1/4 seconds relieves the effect.
By clicking on a yellow checkbox in the depot selection dialog, the
corresponding index files are removed. This way, index files can
be update by removing and downloading them again.
This patch also filters out sculpt-managed components from the graph to
avoid erratic graph-position changes while the '+' menu is open.
Fixes#3193
Without this patch, a version change of an already exited child would not
trigger the restart of the child because the version is evaluated as
late as the child configuration, but only if the child has not exited
yet.
This patch evaluates the version at the earlier stage where the identity
of the child (its name) is checked against the new configuration.
Fixes#3226
The disk image contains an extended partition table now that would
have been parsed incorrectly in the past. While there remove the unused
gpt BLOB (test-part_block_gpt has its own raw archive).
Issue #3223.
The fs_tool component performs file operations according to its
configuration. This initial version implements only the operation
<remove-file> as needed for Sculpt CE.
Issue #3222
Issue #3193
This patch refines the criterion of when the networking is considered as
ready to use. Until now, any IP reported by the NIC router was taken as
an indicator for connectivity. But as the NIC router reports an IP
0.0.0.0/32 when no network cable is plugged at the uplink, the condition
was too loose.
* Introduces pending_signal syscall to check for new signals for the
calling thread without blocking
* Implements pending_signal in the base-library specific for hw to use the
new syscall
Fix#3217
This patch improves the error handling of depot-download manager for the
case where a download is requested but the corresponding software
provider information is absent from the depot. Without this patch, the
update mechanism would get stuck in the failed depot-query step and
won't attempt to perform subsequent download jobs.
Fixes#3224
The storage dialog is folded when activating the runtime view (e.g., by
clicking on the Genode Logo). This should happen immediately as response
of the mouse click.
This patch improves the separation of the update and layout phases to
avoid superfluous geometry animations of its child widgets. Prior this
patch, 'Widget::geometry' was called in both phases, potentially
triggering geometry animations with intermediate values at the update
phase.
Related to issue #3221
The button widget already supported an animated transition between
hovered and unhovered states. This patch generalizes the mechanism to
allow animated transitions between arbitrary button states, including
style changes.
This way, the fade-out of non-TCB components in Sculpt CE happens not
abruptly but smooth.
Fixes#3221
This patch makes the application of color/alpha from the icon's texture
to the target surface customizable by replacing the formerly built-in
'_transfer_pixel' function by calls to the new 'Pixel_rgba::transfer'
interface.
Issue #3221
The new 'transfer' function interface defines how pixel/alpha values
sampled from texture are applied to a destination pixel, similar to the
role of a fragment shader in GPU-based rendering. The transfer function
can be customized by defining custom pixel types, which may be (but
don't need to be) derived from 'Pixel_rgba'.
Issue #3221
The default 'Rect' constructor constructs an invalid rectangle where the
p1 coordinates are lower than the p2 coordinates. In particular, p1 is
set to (1, 1). The 'Widget' implementation uses the points individually
as input into the 'Animated_rect' mechanism. This way, widgets end up
being positioned at (1, 1) initially and are moved to (0, 0) once the
first layout update is applied. By explicitly initializing the
'_geometry' to (0x0+0+0), we avoid this initial artifact.
When entering/leaving sub menus of Sculpt's '+' menu, some parts of the
menu sometimes remain unchanged, in particular the back button.
Originally, a click would reset the hovering on clicks in the
expectation that any click would eventually result in a completely new
situation where the old hovering information does not make sense and
would only (potentially) confuse the menu. But this was apparently
overzealous. With the patch a once hovered back button stays hovered
even when actitivated and the back button of the upper-level menu
happens to stay under the current pointer position.
Issue #3209
This patch improves the hover handling in situations where the dialog
changes under the pointer. Previously, hover changes were reported
as response to user input only, which failed to cover this case. This
became a problem with Sculpt CE's '+' menu, which changes on the fly
when entering/leaving sub menus.
The patch also cleanly separates the hover handling from the focus
handling. Originally, the hovering was reset when the menu view got
unfocused. In situations like Sculpt's '+' menu where the menu view
receives a transient focus only while clicked and gets unfocused on the
button-release event (aka clack), each clack would invalidate the hover
information until a new input event comes in.
Finally, the patch introduces the clear distinction between situations
where the entire dialog is hovered or not. Previously, this state was
somehow implicitly kept by issuing an invalid hover report whenever a
leave event was observed.
Issue #3209
When a window is moved, the virtual pointer position must be updated,
taking the changed input coordinate into account. This patch propagates
such changes via absolute motion events to the client.
Without this patch, Sculpt CE's '+' menu wouldn't update the hovered
item correctly when entering/leaving sub menus (which happen to trigger
the repositioning of the menu on screen).
Issue #3209
The site download.qt.io seems to apply some mirror-via-HTTP-redirect
scheme which, unfortunately, seems broken (and therefore annoyingly
slow) for non-SSL-secured URLs.
* Introduce 64-bit tick counter
* Let the timer always count when possible, also if it already fired
* Simplify the kernel syscall API to have one current time call,
which returns the elapsed microseconds since boot
When specifying the attribute 'dep_visible="false"' for a primary
dependency or the attribute 'visible="false"' for a secondary
dependency, the dependency is used for the layout calculation but not
displayed in the graph.
- Omit showing routes to uninteresting ROMs obtained from the parent,
i.e., the binaries requested by the sculpt-managed subsystems.
- Change the routes for the inspect subsystem such that the inspect-noux
instance is anchored at the config node (critical!) and the nit_fb
instance anchored at the used GUI.
The "schedule_post_signal_hook" method of the Genode::Entrypoint class
is problematic because the signal hook can be scheduled and replaced
multiple times during the signal dispatch cycle. Add an alternative to
this method with "register_io_progress_handler" and the "Post_signal_
hook" class with "Io_progress_handler". The difference being an
"Io_progress_handler" may be registered once during the lifetime of an
entrypoint to prevent arbitrary libraries from replacing a pending hook.
The "register_io_progress_handler" remains as a deprecated API, and is
now invoked for every I/O signal received and only for I/O signals
rather than for any signal.
Ref #3132