Instead of bailing out if the channel list is incorrect check config
node attributes and default settings first.
Being there also fix flawed LOG messages.
Fixes#1794.
* enable i915 driver from Linux 3.14.5
* tested for generation 5 till 8 GPUs
The driver can be configured at run-time via the config ROM. Every
connector of the graphic card can be configured separately using the
following syntax
<config>
<connector name="LVDS-11" width="1280" height="800" enabled="true"/>
</config>
Also, when enabled within the intel framebuffer driver configuration like
the following
<config buffered="yes"/>
a simple ram dataspace is propagated to the client and the driver
itselfs copies from that buffer to the framebuffer triggered via refresh
calls. This option is useful to alleviate tearing effects.
The driver distributes all available connectors of the graphic card and
their supported resolutions via a report. It looks like follows
<connectors>
<connector name="LVDS-11" connected="1">
<mode width="1280" height="800" hz="60"/>
...
</connector>
...
</connectors>
The driver distributes the report only if this is stated within its
configuration, like the following
<config>
<report connectors="yes"/>
</config>
Fix#1764
This patch unifies the mechanism of selecting server-side policies and
taking session-routing decisions based on session labels. In both cases,
XML nodes are scored against session labels. The score depends on the
XML attributes 'label' (exact match), 'label_prefix', and
'label_suffix'.
Issue #1766
* Provide paravirtualized block API for accessing the second partition
of the block device that is provided by the ESDHC driver.
* Provide paravirtualized serial API for sending log-output over Genodes
serial port.
* Use the latest Linux suggested in the USB Armory Wiki [1] when on USB Armory
while still using the older vendor Linux when on i.MX53 QSB. I.e.,
provide a device tree through RAM and a rootfs through the paravirtualized
block device when on USB Armory while providing ATAGs and Initrd when on
i.MX53 QSB.
* Switch on the LED on the USB Armory when the VMM catches a VM-exception
and switch it off again when as soon as the exception is handled. This
merely show-cases the ability to instrument the LED for such purposes. In an
ideal world, the LED is switched on as long as we're on the "Secure Side"
and switched off as long as we're not.
* For further information see repos/os/run/tz_vmm.run
[1] https://github.com/inversepath/usbarmory/wiki/Preparing-a-bootable-microSD-imageFixes#1497
On the USB Armory, we want to secure different devices than on other i.MX53
implementations. Thus, add a board specific configuration that is interpreted
by the kernel Trustzone initialization.
Ref #1497
Enhance the VM state, that can be accessed by a VMM, by a member
'unsigned irq_injection'. In Kernel::Vm::proceed check, whether
irq_injection is set. If so, check whether irq_injection is a
non-secure IRQ. If so, let the PIC raise this IRQ in the VM and reset
irq_injection.
Ref #1497
This enables installation of the bootloader image without wiping the
partition table which is needed at least for the tz_vmm tutorial with
hw_usb_armory.
Ref #1497
Move ADMA2 stuff to extra header and unit. Move ESDHCv2 implementations to
extra unit. Use exceptions instead of error codes. Clean-up documentation.
Ref #1497
The manual termination of multi-block writes via "Stop Transmission" commands
seems to leave the card in a busy state sometimes. This causes errors on
subsequent commands. Thus, we have to synchronize manually with the
card-internal state via "Send State" commands. Additionally, the method
for issuing the manual "Stop Transmission" commands was refined.
Ref #1497
We have to issue a data synchronization barrier after writing a ADMA2
table to ensure that the corresponding write commands were actually
executed before issuing the SD command.
Ref #1497
On i.MX53 QSB, a "Send Op Cond" command during the driver initialization
returns another response value than on the USB Armory. As the check for
this response seems to have no relevance for the driver functionality (Linux
reads the value from MMIO but I can't find a place in the source code where
it is used), we simply remove it.
Ref #1497
Previously, it was not necessary to acknowledge an IRQ initially before using
it. However, since the IRQ framework changed lately it is. Adapt to this.
Ref #1497
Notify client initially to enforce a client-side ROM update. Otherwise,
a server-side ROM update between session creation and signal-handler
registration would go unnoticed.
Issue #1788
This patch changes the decorator to always apply stacking-order changes
immediately instead of deferring the re-stacking of the nitpicker views
to the next call of 'update_nitpicker_views'. The deferred application
did not always work when more then one windows changed their stacking
position at once because the cached '_neighbor' values interfered with
each other.
The eager re-stacking should not have negative effects on the user
experience because, in contrast to re-positioning, re-stacking a rare
operation.
