MorseTrackerHWCode/ArduTracker.ino

// Sweep
// by BARRAGAN <http://barraganstudio.com> 
// This example code is in the public domain.


#include <Servo.h> 
 
Servo pan;  // pan servo
Servo tilt; // tilt servo

// Pin 13 has an LED connected on most Arduino boards.
int led = 13;
long lastTilt = 65L;
long lastPan = 50L;
int dir = 1;
int pos = 0;
int tiltDelay = 15;
long minPWM = 1000L;
long maxPWM = 2000L;
long panVal = 0L;
long tiltVal = 0L;
long interpVal = 0L;

String cmd = "";
String panStr = "";
String tiltStr = "";

void setup() 
{ 
  pan.attach(9);  
  tilt.attach(10);
  
  Serial.begin(57600);

  pinMode(led, OUTPUT);     

  // Origin for both servos
  tilt.write(lastTilt);
  pan.write(lastPan);
} 
 
 
void loop() 
{ 
  if (Serial.available()) 
  {
    char ch = Serial.read();

    if (ch == 10)
    {
      digitalWrite(led, HIGH);   // turn the LED on (HIGH is the voltage level)
      
      // Line feed is the command char
      if (cmd.startsWith("!!!PAN:"))
      {
        panStr = cmd.substring(7,11);
      
        if (cmd.substring(12,16) == "TLT:")
        {
          tiltStr = cmd.substring(16,20);
        }

        if (panStr != "")
        {
           panVal = panStr.toInt();
           if (panVal < minPWM)
           {
             panVal = minPWM;
           }        
         
           if (panVal > maxPWM)
           {
             panVal = maxPWM;
           }
       
           interpVal = ((panVal-minPWM) * 360) / (maxPWM-minPWM);  
         
            if (interpVal > 360)
            {
              interpVal = 360;
            }
        
            if (interpVal < 0)
            {
              interpVal = 0;
            }

            //Serial.print("Pan=");
            //Serial.println(interpVal);
      
            // This is the calibration constant for the pan which has a gear ratio
            interpVal = ((interpVal * 10) / 37) + 50;
            pan.write(interpVal);
            lastPan = interpVal;
        }
      
        if (tiltStr != "")
        {
           tiltVal = tiltStr.toInt();
           if (tiltVal < minPWM)
           {
             tiltVal = minPWM;
           }        
         
           if (tiltVal > maxPWM)
           {
             tiltVal = maxPWM;
           }
         
           interpVal = ((tiltVal-minPWM) * 90) / (maxPWM-minPWM);  
           
            if (interpVal > 90)
            {
              interpVal = 90;
            }
          
            if (interpVal < 0)
            {
              interpVal = 0;
            }
  
            //Serial.print("Tilt=");
            //Serial.println(interpVal);
            
            // This is the calibration constant
            interpVal = 150 - interpVal;
  
            dir = 1;
            if (interpVal < lastTilt)
            {
              dir = -1;
            }
          
            if (tiltDelay > 0)
            {
              // Slow down tilt by stepping to it's destination
              for (pos = lastTilt; pos != interpVal; pos += dir)
              {                                  
                tilt.write(pos);              
                delay(tiltDelay);                       
              } 
            }
            else
            {
              tilt.write(interpVal);
            }
         
            lastTilt = interpVal;
        }
      }
      else if (cmd.startsWith("!!!TLTDLY:"))
      {
        cmd = cmd.substring(10,14);
        tiltDelay = cmd.toInt();
      }
      
      panStr = "";
      tiltStr == "";
      cmd = "";

      digitalWrite(led, LOW);    // turn the LED off by making the voltage LOW         
    }
    else
    {
      cmd += ch;
    }
  }
}